Instrukcja obsługi Paradigm BX-12SQ

Paradigm subwoofer BX-12SQ

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Paradigm BX-12SQ (2 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
INSTALLATION INSTRUCTIONS FOR BX-12SQ BACKBOX AND RVC-12SQ SUBWOOFER
STEP 2
PARADIGM DOES NOT SUPPLY SCREWS FOR MOUNTING BACKBOX
TO WALL. CHOOSE SCREWS APPROPRIATE FOR WALL COMPOSITION
AND WEIGHT OF BACKBOX WITH SUBWOOFER.
BX-12SQ BACKBOX: 26.4 lb / 12.0 kg
RVC-12SQ SUBWOOFER: 14.3 lb / 6.5 kg
TOTAL WEIGHT: 40.7 lb / 18.5 kg
IF YOU ARE NOT COMFORTABLE PERFORMING THE FOLLOWING PROCEDURE,
CONTACT A PROFESSIONAL INSTALLER.
NOTE: The required amount of damping material is included and correctly positioned in backbox. DO NOT remove, compact or add additional damping material. DO NOT add
damping material to wall directly behind backbox.
PARTS INCLUDED:
• 1 – Backbox • 2 – Mounting Brackets
• 1 – Wire Loop with screw • 1 – Removable MDF cover with 4 screws
• 4 – Gasket Tape Strips • 1 – Mounting Template
PARTS NOT INCLUDED:
• Minimum of 16 – #6 Drywall Screws (8 to attach brackets to box;
8 to attach box to wall) 3˝ Drywall nails may also be used to attach box to wall
NOTE: DO NOT PUNCTURE OR REMOVE THE PROTECTIVE PLASTIC THAT
COVERS PORT HOLES UNTIL READY TO INSTALL SUBWOOFER
60 in / 152.4 cm
TIP: Paint subwoofer before installing.
To prevent stray resonances from coloring output, backbox should
not touch studs—center it between studs.
INSTALLING BACKBOX
CAUTION: Mounting brackets are made of
galvanized steel. Edges may be sharp.
INSTALLING BRACKETS
NOTE: Wire loop to harness speaker wire must
be attached with screw provided.
BACKBOX DIMENSIONS
14 in / 35.6 cm
3-3/8 in
8.6 cm
WARNING! Ports run vertically inside
backbox. To avoid damage, position
installation brackets as shown.
STEP 1
FOR USE WITH 5/8˝ OR 1/2˝ DRYWALL ONLY
STEP 4
INSTALLING SUBWOOFER
Remove protective cover. To prevent air leaks, before installing subwoofer, a
pply gasket tape
(included with subwoofer)
along
all 4 outer edges of box, overlapping tape at corners.
Remove port covers by pressing them out
(as shown)
.
Holding subwoofer firmly, push it into backbox being careful to align top holes in subwoofer with top holes in backbox.
Screw in until firm but not fully tightened. Continue holding subwoofer firmly and line up all bottom holes. Again, screw
in until firm but not fully tightened. Insert remaining screws. Tighten all screws.
RED (+) BLACK (–)
INSTALLING GRILLE
STEP 3
STEP 7 STEP 8
8 – #8-32 Machine Screws (to attach subwoofer
to backbox) and gasket tape strips are included
with subwoofer.
MAN1001006 | 2009.2
Snake wire through wire loop then along wall to amplifier location before drywalling.
WIRING
STEP 5
When cutting opening in drywall use the
dimensions provided below as a guide.
IMPORTANT! When laying drywall over
backbox, center hole cutout over MDF
cover, allowing an even gap on all sides.
DRYWALLING
Apply a strip of gasket tape along all 4 sides, overlapping tape at corners.
APPLYING GASKET TAPE
For subwoofer to
function correctly
and avoid damage
to amplifier or subwoofer, the
Impedance Matching Switch
must be correctly positioned.
Move the switch position to
reflect designated amplifier.
Refer to the Owners Manual
included with the amplifier
for more information.
NOTE: Dimensions
shown are for the
inside cutout.
12-5/8 in / 32.0 cm
16-7/16 in / 41.7 cm
IMPORTANT! To prevent dust and dirt
from entering backbox, do not remove
cover until ready to install subwoofer.
IMPORTANT! Port gaskets have
been factory-installed on your
Paradigm®RVC-12SQ backbox. If
you find additional gaskets packaged
with your subwoofer, please note
they are no longer required.

Specyfikacje produktu

Marka: Paradigm
Kategoria: subwoofer
Model: BX-12SQ

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Paradigm BX-12SQ, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje subwoofer Paradigm

Paradigm

Paradigm Defiance V8 Instrukcja

29 Września 2024
Paradigm

Paradigm Defiance V12 Instrukcja

29 Września 2024
Paradigm

Paradigm UltraCube 10 Instrukcja

29 Września 2024
Paradigm

Paradigm Defiance X12 Instrukcja

29 Września 2024
Paradigm

Paradigm UltraCube 12 Instrukcja

29 Września 2024
Paradigm

Paradigm SUB 1 Instrukcja

29 Września 2024
Paradigm

Paradigm SUB 15 Instrukcja

29 Września 2024
Paradigm

Paradigm SUB 2 Instrukcja

29 Września 2024
Paradigm

Paradigm Cinema SUB Instrukcja

29 Września 2024
Paradigm

Paradigm RVC-12SQ Instrukcja

27 Września 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

ETON

ETON Graphit 8-2 Instrukcja

19 Marca 2025
ETON

ETON Graphit 8-4 Instrukcja

19 Marca 2025
ETON

ETON Graphit 10-4 Instrukcja

19 Marca 2025
ETON

ETON MW 10 FLAT Instrukcja

19 Marca 2025
ETON

ETON PW 8 Instrukcja

19 Marca 2025
ETON

ETON USB 6 AR Instrukcja

19 Marca 2025
Morel

Morel Ultimo Powerslim 124D Instrukcja

12 Marca 2025
Morel

Morel Ultimo Powerslim 104D Instrukcja

12 Marca 2025
Rockustics

Rockustics OneSub Instrukcja

9 Marca 2025
Phase Technology

Phase Technology PL-10s Instrukcja

5 Marca 2025