Instrukcja obsługi Panduit CT-100B

Panduit nieskategoryzowany CT-100B

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Panduit CT-100B (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 20 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

WARNING:

El Shoectric ck Hazar d:

Do NOT use this tool

on live wire.

Verify power is “OFF” before

working on wiring with this tool.

The plastic grips are for the user’s comfort,

and are not intended to insulate against

electrical shock while working on

live electrical circuits.

NON-INSULATED AND INSULATED

PARALLEL SPLICE INSTRUCTIONS

1. Insert stripped wire into each end of the

parallel splice. (See product packaging for

proper strip lengths.)

2. Locate parallel splice in proper crimp

pocket.

3. Position crimp pocket on the center of the

metal barrel.

4. Squeeze handles firmly.

OPERATION INSTRUCTIONS

CT-100B PA29563A01

REV: 0 0 -21 2 024

See product packaging or contact Customer Service for UL/CSA

approved tooling/product combination.

NOTE: In the interest of higher quality and value, Panduit products are continually

being improved and updated. Consequently, pictures may vary from the

enclosed product.

Page: 1 of 2

E-mail:

techsupport@panduit.com

Technical Support:

1-800-777-3300

CRIMP POCKET

WIRE CUTTER for No. 10

AWG and smaller copper wire.

CRIMPING DIES for Pan-Term

insulated terminals, disconnects,

splices and wire joints on No. 22 to

10 AWG stranded wire.

CUTTERS for machine screws

of sizes shown, open handles,

thread in this side. Closing handles

cuts screw approx. 5/32" below surface.

CRIMPING DIE for Pan-Term

non-insulated terminals, disconnects,

splices and wire joints on No. 22 to

10 AWG solid or stranded wire.

CRIMP POCKETS A and B for

additional terminals and disconnects

per instructions on product packaging.

WIRE LOOP HOLES (2)

WIRE STRIPPER for removing plastic

or rubber wire insulation. Strip length

should allow a minimum of 1/32" of

conductor to extend beyond

terminal barrel.

red dot

blue dot

yellow dot

This tool is made

of hardened steel

and is protected

with a light coat

of oil.

OPERATION

INSTRUCTIONS

CT-100B

CRIMPING TOOL

www.panduit.com

Page: 2 of 2

NON-INSULATED

TERMINAL AND DISCONNECT

INSTRUCTIONS

1. Insert stripped wire into terminal or

disconnect until a minimum of 1/32" of

conductor extends beyond barrel. (See

product packaging for proper strip lengths.)

2. Locate terminal or disconnect in proper non-

insulated crimp pocket.

3. Position crimp pocket on the center of the

metal barrel.

4. Squeeze handles firmly.

INSULATED

TERMINAL AND DISCONNECT INSTRUC-

TIONS

1. Insert stripped wire into terminal or

disconnect until a minimum of 1/32" of

conductor extends beyond barrel. (See

product packaging for proper strip lengths.)

2. Locate terminal or disconnect in proper

insulated crimp pocket.

3. Position crimp pocket on the center of the

metal barrel.

4. Squeeze handles firmly.

5. Close insulation if desired.

NON-INSULATED WIRE JOINT

INSTRUCTIONS

1. Twist ends of stripped wire together, trim

and insert into wire joint. (See product

packaging for proper strip lengths and

trimming instructions.)

2. Locate wire joint in proper non-insulated

crimp pocket.

3. Position crimp pocket on the center of the

metal barrel.

4. Squeeze handles firmly.

INSULATED WIRE JOINT

INSTRUCTIONS

1. Twist ends of stripped wire together, trim and

insert into wire joint. (See product packaging

for proper strip lengths and trimming

instructions.)

2. Locate wire joint in proper insulated crimp

pocket.

3. Position crimp pocket on the center of the

metal barrel.

4. Squeeze handles firmly.

5. Close insulation if desired.

CRIMP POCKET

CRIMP POCKET CRIMP POCKET

INSULATED BUTT SPLICE

INSTRUCTIONS

1. Insert stripped wire into end of the butt

splice to internal wire stop. (See product

packaging for proper strip lengths.)

2. Locate butt splice in proper insulated crimp

pocket.

3. Position crimp pocket on the center of the

metal barrel half with wire inserted.

4. Squeeze handles firmly.

5. Close insulation if desired.

6. Repeat for other end of butt splice.

CRIMP POCKET

NON-INSULATED BUTT SPLICE

INSTRUCTIONS

1. Insert stripped wire into end of the butt

splice to internal wire stop. (See product

packaging for proper strip lengths.)

2. Locate butt splice in proper non-insulated

crimp pocket.

3. Position crimp pocket on the center of the

metal barrel half with wire inserted.

4. Squeeze handles firmly.

5. Repeat for other end of butt splice.

CRIMP POCKET CRIMP POCKET

OPERATION INSTRUCTIONS

Specyfikacje produktu

Marka:	Panduit
Kategoria:	nieskategoryzowany
Model:	CT-100B
Kolor produktu:	Czarny
Wysokość produktu:	16 mm
Szerokość produktu:	52.75 mm
Waga produktu:	253 g
Model:	Narzędzie do zaciskania
Materiały:	Stal
Długość produktu:	234.21 mm
Materiał uchwytu:	Plastik
AWG przekrój przewodu (min):	22
AWG przekrój przewodu (max):	10