Instrukcja obsługi Panamax MR5100

Panamax Niesklasyfikowane MR5100

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Panamax MR5100 (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

Speciﬁcations subject to change due to product upgrades and improvements.

*Go to www.panamax.com for detailed noise ﬁltering information.

Español - Para la versión en español de este documento, vaya a www.panamax.com/products

Français - Pour la version espagnole de ce document, allez à www.panamax.com/products

DIN-00017 - REV. D

OUTLET BANKS 1, 2 and 3

INDICATOR LEDS

POWER ON / OFF

ON / OFF, CONTROL FOR

DECORATIVE BLUE LIGHTS AND VOLTMETER

(Voltmeter and blue lights can be illuminated when power is off)

SAFE POWER AND

VOLTAGE INDICATOR

UNSAFE VOLTAGE

INDICATOR

LINE FAULT

INDICATOR

FRONT PANEL

CONVENIENCE OUTLET

(SWITCHED)

USB CHARGER

5VDC, 500mA

10 ft. POWER

CORD,

NEMA 5-15

GROUND LUG

15 AMP CIRCUIT

BREKAER

RESETTABLE

OUTLET BANK 3

(DELAYED CURRENT)

OUTLET BANK 2

(SWITCHED)

OUTLET BANK 1

(ALWAYS ON)

LAN SURGE

PROTECTION

1 PAIR OF

RJ-45 IN/OUT

CONNECTORS

COAXIAL SURGE

PROTECTION

2 PAIRS

UNIVERSAL

IN/OUT

CONNECTORS

TELCO SURGE PROTECTION

1 PAIR OF RJ-11 IN/OUT CONNECTORS

Note to CATV Installers:

This reminder is provided to call attention to Article 820-40 of the NEC. That article provides

speciﬁc guidelines for proper grounding.It speciﬁes that the cable ground shall be connected

to the grounding system of the building and as close to the point of entry as practical.

Front Panel Features

MR5100 Features and Speciﬁcations

Panamax LLC, 1800 South McDowell Blvd., Petaluma, CA 94954 • 707-283-5900 • 800-472-5555 • www.panamax.com

Model MR5100 Reference Guide

AC PROTECTION

Protect or Disconnect Circuitry_________________________________________________Yes

Patented Power Management Circuit____________________________________________Yes

Overvoltage Shutoff____________________________________________________ 140V ±3V

Undervoltage Shutoff___________________________________________________ 100V ±1V

Thermal Fusing___________________________________________________________Yes

Line Voltage___________________________________________________120VAC, 50/60HZ

Initial Clamping Level__________________________________________ 200V Peak, 141VRMS

Voltage Protection Rating (UL 1449 3rd Edition, 3,000A)____________________________400V

Protection Modes_________________________________________________ L-N, L-G, N-G

Maximum Current Rating_____________________________________________15A (1800W)

EMI/RFI Noise Filtration______________________________ Panamax Level 3 Noise Filtration*

Response Time__________________________________________________________< 1ns

Single Pulse Energy Dissipation_________________________________________2025 Joules

Peak Impulse Current___________________________________________________52,000 A

LAN PROTECTION

Clamping Level____________________________________________________ 62±6V @ 1 mA

Compatibility___________________________________________________10/100/1000bT

Wires Protected _______________________________________________________8-Wires

Connectors____________________________________________________________RJ-45

TEL PROTECTION

Fuseless/Auto-Resetting________________________________________________Yes

Clamping Level__________________________________________________________260V

Wires Protected _________________________________________________ 2 wire, 1 pair (4, 5)

Connectors_________________________________________________________RJ-11

UNIVERSAL COAX PROTECTION

HD 1080 i/p Ready_________________________________________________________Yes

Bidirectional__________________________________________________________Yes

Shielded____________________________________________________________Yes

Clamping Level___________________________________________________________75V

Frequency Range_________________________________________________OMHz - 2.2 GHz

Insertion Loss_________________________________________________________ <0.5 dB

Connections______________________________________________ Female “F”, Gold Plated

Key Features

Exclusive Automatic Voltage Monitoring (AVM)

Panamax’s patent pending power monitoring

circuitry constantly monitors the AC line voltage

for unsafe voltage conditions such as momentary

spikes, prolonged over-voltages and under-volt-

ages (brownouts). These unsafe conditions pose

a very dangerous threat to all electronic equip-

ment within the home. If the MR5100 senses

an unsafe power condition, it will automatically

disconnect power from your equipment to pro-

tect equipment from damage. The front panel

indicator will also alert users to the power condi-

tion. Once the voltage returns to a safe level, the

MR5100 will automatically reconnect the power

to the outlets.

Protect or Disconnect™ Technologies

In the event of a catastrophic surge such as light-

ning, it completely disconnects AC power to con-

nected equipment.

Front Panel Outlet

MR5100 features a protected and noise ﬁltered

convenience outlet located on the front panel.

Perfect for temporary gaming systems, por-

table electronics (such as music players or smart

phones), or other personal electronics.

Front Panel Decorative Lights

Blue decorative lights add an attractive look at feel

to your equipment rack or TV cabinet.

Antenna, Cable, Sat and LAN Signal protection

Coaxial protection circuits prevent damaging

surges from entering through signal paths and

have the smallest signal loss on the market - less

than 0.5 db of attenuation from 0Hz to 2.2GHz.

Our coaxial protection has been speciﬁcally

designed to virtually eliminate signal loss. The

clamping level of 75V will meet and exceed the

demands of both cable and satellite voltages

while minimizing exposure to damaging spikes

and surges. LAN protection allows for 10/100

base-T Ethernet equipment to integrate into an

audio/video system without the risk of upstream

surge damage from a gateway, switch, router or

other network device.

Eleven Protected and Filtered Power Outlets

(see speciﬁcations)

Ten Foot Power Cable with Straight Plug

NEMA 5-15P, ﬁxed starin relief, unshielded,

straight plug.

TO GET STARTED

1. With MR5100 disconnected from the wall outlet, plug the equipment to be protected into the MR5100

AC outlets.

2. Connect any LAN, TELEPHONE and COAX lines to be protected to the appropriate connectors on the

MR5100.

3. Plug the MR5100 into the wall outlet and verify that the LINE FAULT INDICATOR LED is NOT lit, indicat

ing that the wall outlet is properly wired and grounded. If it is LIT, call a licensed electrician to inspect and

implement proper and safe wiring.

4. Turn on MR5100 by pressing the POWER ON button and proceed to turn on your connected equipment.

IMPORTANT SAFETY POINTS

Panamax surge protectors and the connected equipment must be indoors, in a dry location and in the same

building. Although your Panamax protector is very durable, its internal components are not isolated from the

environment. Do not install any Panamax product near heat emitting appliances such as a radiator or heat register.

Do not install this product where excessive moisture is present; for example near a bath tub, sink, pool basement

ﬂoor, ﬁsh tank, etc. It is not uncommon for a building to be improperly grounded. In order to protect your equipment,

Panamax products must be plugged into a properly wired and grounded 3-wire outlet. Additionally, building wiring

and grounding must conform to applicable NEC (USA) or CEC (Canada) codes for the Panamax protection policy to

be valid. Do not use 2-blade adapters or any other “power strips” with this product. Use only Panamax extension

cord, or a UL / CSA recognized power cord.

Back Panel Features

BANK 1 ON

INDICATOR LIGHT

BANK 1 BANK 2 BANK 3

MR5100

CATV / SAT 1

UNIVERSAL COAX PROT ECT IO N

CATV / SAT 2

TEL

OUT

LAN

OUT

TEL

LAN

OUT

BANK 3

HIGH CURRENT

DELAYED

OUT LET S

BANK 1

FILTERED / LIFT

ALWAYS ON

OUT LET S

BANK 2

FILTERED / LIFT

SWITCHED OUT LET S BANK 1 ON

GROUND

LUG

15 AMP

CIRCUIT

BREAKER

MAIN POWER 120 VAC/15A

LAN PROTECTION

TEL PROT ECT IO N

MR5100 Limited Product Warranty and Connected Equipment Policy Information

CAUTION!

All Panamax Warranties and Connected Equipment Policies are valid only in the United States and Canada.

CAUTION!

Audio/Video, computer and/or telephone system installations can be very complex systems, consisting of many interconnected components.

Due to the nature of electricity and surges, a single protector may not be able to completely protect complex installations. In those cases, a systematic approach using multiple protectors must be

employed. Systematic protection requires professional design. AC power, satellite cables, CATV cables, telephone/network lines, signal lines or any other electrical conductors, entering the system

that do not pass through this surge protector may invalidate the Panamax Connected Equipment Protection Policy. For additional information on how to protect your system, please contact Panamax

before connecting your equipment to the surge protector.

CAUTION!

WARRANTY LIMITATION FOR INTERNET PURCHASERS

Panamax products purchased through the Internet do not carry a valid Product Warranty or Connected Equipment Protection Policy unless purchased from an Authorized Panamax Internet Dealer

and the original factory serial numbers are intact (they must not have been removed, defaced or replaced in any way). Purchasing from an Authorized Panamax Internet Dealer insures that the product

was intended for consumer use, has passed all quality inspections and is safe. Buying through auction sites or unauthorized dealers may result in the purchase of salvaged, failed and/or products not

intended for use in the US. In addition, Authorized Panamax Internet dealers have demonstrated sufﬁcient expertise to insure warranty compliant installations. For a list of Authorized Panamax Internet

Dealers go to www.panamax.com. If you have any questions regarding these requirements, please contact Panamax Customer Relations.

Product Upgrade Program

If your Panamax power conditioner sacriﬁces it-

self while protecting your connected equipment,

you have an option to upgrade to the latest tech-

nology. Please go to our web site www.panamax.

com or contact Panamax Customer Relations at

800-472-5555 for details.

Panamax Power

Conditioner Limited

Product Warranty

Panamax warrants to the purchaser of this Pan-

amax audio/video component style power condi-

tioner, for a period of three (3) years from the

date of purchase, that the unit shall be free of

defects in design, material or workmanship, and

Panamax will repair or replace any defective unit.

For product replacement see “NOTIFICATION”

section (3).

Panamax Power Conditioner

Limited Connected Equipment

Protection Policy

It is the policy of Panamax that it will, at its elec-

tion, either replace, pay to replace at fair market

value, or pay to repair, up to the dollar amount

speciﬁed below, equipment that is damaged by

an AC power, cable, telephone, or lightning surge

while connected to a properly installed Panamax

power conditioner. To be eligible for compensa-

tion, repair and or replacement, the power condi-

tioner must shows signs of surge damage or that

it is operating outside of design speciﬁcations,

relative to its surge protection capability, and un-

der all of the circumstances failed to protect your

connected equipment.

MR5100: $5,000,000

THE CONNECTED EQUIPMENT POLICY IS

SUBJECT TO THE FOLLOWING CONDITIONS

AND LIMITATIONS

1. ORIGINAL OWNERSHIP REQUIREMENT:

Panamax’s connected equipment policy extends

to the original purchaser of the Panamax product

only and is non-transferable. Original purchase

receipts must accompany any product return or

claim for connected equipment damage.

2. PROPER INSTALLATION: Panamax AC protec-

tors must be directly plugged into a properly

grounded 3-wire AC outlet. Extension cords*,

non-grounded two prong adapters, or other

non-Panamax surge products must not be used.

Building wiring and other connections to protect-

ed equipment must conform to applicable codes

(NEC or CEC). No other ground wires or ground

connections may be used. All wires (including,

e.g., AC power lines, telephone lines, signal/

data lines, coaxial cable, antenna lead-ins) lead-

ing into the protected equipment must ﬁrst pass

through a single Panamax protector designed for

the particular application. The protector and the

equipment to be protected must be indoors in a

dry location, and in the same building. Panamax

installation instructions and diagrams must be

followed

3. NOTIFICATION: You must notify Panamax with-

in ten days of any event precipitating request for

product replacement or payment for connected

equipment damage. A return authorization (RA)

number must ﬁrst be obtained from the Pan-

amax Customer Relations Department at www.

panamax.com** before returning the protector

Panamax. At this time, you must notify Panamax

if you believe you have a claim for damaged con-

nected equipment. Once you obtain an RA num-

ber, please mark the number on the bottom of

the unit and pack it in a shipping carton/box with

enough packing material to protect it during tran-

sit. The RA number must also be clearly marked

on the outside of the carton. Ship the unit Pan-

amax. Please note that you are responsible for

any and all charges related to shipping the unit to

Panamax. If connected equipment damage was

indicated on your RA request, Panamax will mail

you claim kit to be completed and returned within

30 days. A connection diagram of your system

will be required as part of the claim kit. Be sure to

note its conﬁguration before disconnecting your

equipment.

4. DETERMINATION OF FAILURE: Panamax will

evaluate the protector for surge damage. The

Panamax protector must show signs of surge

damage or must be performing outside (>10%)

of design speciﬁcations relative to its surge

protection capability. Opening the enclosure,

tampering with, or modifying the unit in any way

shall be grounds for an automatic denial your

request for payment. Panamax, after evaluating

all information provided, will determine whether

or not your request is eligible for payment. If the

surge protector shows no signs of AC power or

signal line surge damage and is working within

design speciﬁcations, Panamax will return the

unit to you with a letter explaining the test results

Exceptions: If a dealer or installer replaces the

protector for the customer, replacement will be

returned to the dealer installer; or if the protec-

tor is a pre-1996 model, it will be replaced; or,

for a Canadian customer, the protector will be

replaced. Panamax reserves the right to inspect

the damaged connected equipment, parts, or cir-

cuit boards. Please note that you are responsible

for any and all charges related to shipping the

damaged equipment to Panamax. Panamax also

reserves the right to inspect the customer’s facil-

ity. Damaged equipment deemed uneconomical

to repair must remain available for inspection by

Panamax until the claim is ﬁnalized.

5. REQUEST PAYMENTS: Once Panamax has de-

termined that you are entitled to compensation,

Panamax will, at its election, either pay you the

present fair market value of the damaged equip-

ment, or pay for the cost of the repair, or send

you replacement equipment, or pay the equiva-

lence of replacement equipment.

6. OTHER INSURANCE/WARRANTIES: This cover-

age is secondary to any existing manufacturer’s

warranty, implied or expressed, or any insurance

and/or service contract that may cover the loss.

7. EXCLUSIONS: THE PANAMAX CONNECTED

EQUIPMENT PROTECTION POLICY DOES NOT AP-

PLY TO: Service charges, installation costs, rein-

stallation costs; setup cost; diagnostic charges;

periodic checkups; routine maintenance; loss of

use of the product; costs or expenses arising out

of reprogramming or loss of programming and/

or data; shipping charges or fees; service calls;

loss or damage occasioned by ﬁre, theft, ﬂood,

wind, accident, abuse or misuse, and products

subject to manufacturer’s recall or similar event.

8. DISPUTE RESOLUTION: Any controversy or

claim arising out of or relating to Panamax’s

Connected Equipment Protection Policy, or the

alleged breach thereof, shall be settled by arbitra-

tion administered by the American Arbitration As-

sociation under its Commercial Arbitration Rules.

You may ﬁle for arbitration at any AAA location in

the United States upon the payment of the appli-

cable ﬁling fee. The arbitration will be conducted

before a single arbitrator, and will be limited

solely to the dispute or controversy between you

and Panamax. The arbitration shall be held in any

mutually agreed upon location in person, by tele-

phone, or online. Any decision rendered in such

arbitration proceedings will be ﬁnal and binding

on each of the parties, and judgment may be en-

tered thereon in a court of competent jurisdiction.

The arbitrator shall not award either party special,

exemplary, consequential, punitive, incidental or

indirect damages, or attorney’s fees. The parties

will share the costs of arbitration (including the

arbitrator’s fees, if any) in the proportion that

the ﬁnal award bears to the amount of the initial

claim.

9. GENERAL: If you have any questions regarding

the product warranty or the connected equip-

ment protection policy, please contact the Pan-

amax Customer Relations Department at www.

panamax.com. The Limited Product Warranty

and Connected Equipment Policy herein super-

sede all previous warranties and/or Connected

Equipment repair/replacement policies.

THE LIMITED PRODUCT WARRANTY IS THE

ONLY WARRANTY PROVIDED WITH THIS PAN-

AMAX PRODUCT AND ANY OTHER IMPLIED

OR EXPRESSED WARRANTIES ARE NON-EX-

ISTENT.

This warranty may not be modiﬁed except in

writing, signed by an ofﬁcer of the Panamax

Corporation.

* The use of a Panamax extension cord or

equivalent (UL or CSA listed, minimum

14AWG, 3-wire grounded) will not invalidate

the warranty.

** Forms are available on the Panamax web

site for requesting RAs and opening a claim

for connected equipment damage.

MODEL - MR5100

DOC. NO. DWS-00007-D

Effective Date 7/1/12

Contacting Panamax

Panamax, Inc.

1800 South McDowell Blvd.

Petaluma, CA 94954

Phone - 707-283-5900 or 800-472-5555

Fax - 707-283-5901

Web - www.panamax.com

Customer Relations

7:30 AM – 4:30 PM, M-F

Email - custrelations@panamax.com

www.panamax.com

1800 South McDowell Blvd., Petaluma, CA 94954 800-472-5555 707-283-5900 Fax 707-283-5901 www.panamax.com

MODEL UNIT DIMENSIONS WEIGHT CARTON DIMENSIONS WEIGHT UPC MASTER PACK QTY MASTER PACK UPC

MR5100 12”l x 17”w x 3.5”h 13.5 lbs 20” x 24” x 10.3” 18 lbs 050616008945 1 50050616008940

4”h with feet

Part# L655 Rev.G

6SHFLÀFDOO\GHVLJQHGDQGHQJLQHHUHGWRSURYLGHSURWHFWLRQÀOWUDWLRQDQG

SRZHUPRQLWRULQJIRU\RXUKRPHWKHDWHUV\VWHP

Speciﬁcations subject to change due to product upgrades and improvements

Go to www.panamax.com for detailed noise ﬁltering information.

HOME THEATER POWER MANAGEMENT

• 11 Protected & Filtered Power Outlets

• Exclusive Automatic Voltage Monitoring (AVM)

C US

• Antenna, Cable, or Satellite, TEL and LAN Signal Protection

• 10 ft. Power Cable with Straight Plug

SPECIFICATIONS

FEATURES

WEIGHTS, DIMENSIONS AND UPC CODES

0RGHO MR5100

AC PROTECTION

Protect or Disconnect Circuitry__________________________________________Yes

Patented Power Management Circuit_____________________________________Yes

Overvoltage Shutoff____________________________________________140V ±3V

Undervoltage Shutoff___________________________________________100V ±/-1V

Thermal Fusing____________________________________________________Yes

Line Voltage____________________________________________120VAC, 50/60HZ

Initial Clamping Level__________________________________200V Peak, 141VRMS

Voltage Protection Rating (UL 1449 3rd Edition, 3,000A)____________________400V

Protection Modes___________________________________________ L-N, L-G, N-G

Maximum Current Rating______________________________________15A (1800W)

EMI/RFI Noise Filtration__________________________Panamax Level 4 Noise Filtration*

Response Time___________________________________________________< 1ns

Single Pulse Energy Dissipation__________________________________2025 Joules

Peak Impulse Current____________________________________________52,000 A

TEL PROTECTION

Fuseless / Auto-Resetting______________________________________________Yes

Clamping Level __________________________________________________ 260V

Wires Protected _________________________________________ 2 Wire, 1 Pair (4, 5)

Connectors_________________________________________________RJ-11

LAN PROTECTION

Clamping Level___________________________________________62±6V @ 1 mA

Compatibility___________________________________________10/100/1000bT

Wires Protected_________________________________________________8-Wires

Connectors_____________________________________________________RJ-45

UNIVERSAL COAX PROTECTION

HD 1080 i/p Ready_________________________________________________Yes

Bidirectional_____________________________________________________Yes

Shielded_______________________________________________________Yes

Clamping Level____________________________________________________75V

Frequency Range__________________________________________OMHz - 2.2 GHz

Insertion Loss__________________________________________________<0.5 dB

Connections________________________________________Female “F”, Gold Plated

POWER ON / OFF ON / OFF, CONTROL FOR

DECORATIVE BLUE LIGHTS

(Blue lights can be illuminated when power is off)

SAFE POWER AND

VOLTAGE INDICATOR

UNSAFE VOLTAGE

INDICATOR

LINE FAULT

INDICATOR

FRONT PANEL

CONVENIENCE OUTLET

OUTLET BANKS 1, 2 and 3

INDICATOR LEDS USB CHARGER

ALL AC OUTLETS (FRONT AND BACK) INCLUDE SURGE PROTECTION AND POWER FILTRATION

LAN SURGE PROTECTION

1 PAIR OF RJ-45 IN/OUT

CONNECTORS

COAXIAL SURGE PROTECTION

2 PAIRS UNIVERSAL IN/OUT

CONNECTORS

RACK MOUNTABLE

(RACK EARS INCLUDED)

TELCO SURGE PROTECTION

1 PAIR OF RJ-11 IN/OUT

CONNECTORS

GROUND LUG

FT STRAIGHT PLUG

15 AMP CIRCUIT

BREKAER

RESETTABLE

OUTLET BANK 3 (HIGH CURRENT) OUTLET BANK 2 (SWITCHED) OUTLET BANK 1 (ALWAYS ON) with INDICATOR LIGHT

• Protect or Disconnect™ Technology

• Linear Level 4 Noise Filtration

10 F

Specyfikacje produktu

Marka:	Panamax
Kategoria:	Niesklasyfikowane
Model:	MR5100
Kolor produktu:	Czarny
Wbudowany wyłącznik:	Tak
Częstotliwość wejściowa AC:	50 - 60 Hz
Wysokość produktu:	88.9 mm
Szerokość produktu:	431.8 mm
Głębokość produktu:	304.8 mm
Waga produktu:	6123.497 g
Długość kabla:	- m
Ilość:	1 szt.
Ilość portów Ethernet LAN (RJ-45):	2
Czas odpowiedzi (typowy):	1 ms
Możliwości montowania w stelażu:	Tak
Częstotliwość (MHz):	0 - 22000 MHz
Wartość znamionowa udaru energii:	2025 J
Ilość gniazd sieciowych:	11 x gniazdo sieciowe
Wartość nominalna napięcia wejściowego:	120 V
Filtr EMI/RFI:	Tak
Napięcie przebicia (clamping voltage):	200 V
Pobór szczytowy, tryb powszechny:	15 A