Instrukcja obsługi PAC RPK5-GM4101

PAC zestaw samochodowy RPK5-GM4101

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC RPK5-GM4101 (9 stron) w kategorii zestaw samochodowy. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/9
Page 1
PAC® | 866-931-8021 | support@pac-audio.com
©2016 Pacic Accessory Corporation
www.pac-audio.com Rev. 113016
P ifi A C ti
PAC is an AAMP power brand
RPK5-GM4101
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2010-2015 Chevrolet Camaro
Removing the factory radio from the vehicle
1.1 - Apply the parking brake. Move the transmission shift
assembly to the most rearward position possible. Use a
at bladed plastic trim tool and release the retainer tabs
securing the front oor console front cover to the console
assembly. Lift the cover (1) up and rearward making sure that
the accessory power receptacle and the electronic traction
control switch clears the transmission shift assembly. It may be
necessary to pop them loose from the underside to achieve
clearance. Disconnect the electrical connections.
1.2 - Remove the 2 x 7mm bolts (1) securing the radio
control assembly (2) into the dash. Then use a at-
bladed plastic trim tool in order to release the retainer
clips securing the radio control assembly (2) to the
instrument panel. Disconnect the electrical connections.
Parts List
The RPK5-GM4101 includes everything you need for a professional installation of an aftermarket radio in your Camaro.
This kit contains:
1. Dash Kit
• (x1) PAC HVAC Control Panel (Transfer of the factory HVAC knobs is required. See instructions below)
• (x2) Radio Mounting Brackets (One left and one right)
• (x1) Pocket (For single din applications)
• (x8) Radio Mounting Screws
2. RP5-GM4101 (Camaro specic radio replacement module)
3. Camaro specic antenna adapter (BAA-DIN22).
4. Rear camera retention cable for vehicles equipped with the MyLink system.
5. USB retention cable. This cable is compatible with vehicles equipped with the MyLink radios and vehicles equipped with the
standard non-touchscreen radios. It will require that the cable be ran to the back of the center console.
6. AUX retention cable for 2010-2012 vehicles equipped with the standard non-touchscreen radios also equipped with a USB port.
Overview
The RPK5-GM4101 is a complete radio replacement kit with integrated climate control retention for the 2010-2015 Chevrolet
Camaro. This kit utilizes the factory HVAC control knobs for a more factory look and experience. To add to the factory look
and experience the exterior temperature display is retained by a small OLED display at the top of the kit retaining this valuable
vehicle feature. This kit also includes all of the modules and cables needed to retain all of the important features of the factory
system such as OnStar, factory warning chimes, factory Bluetooth, steering wheel mounted radio controls, factory reverse
camera, factory amplier (if equipped), AM/FM reception, factory AUX jack (if equipped) and the factory USB port (if equipped).
Table of Contents: Page:
1. Factory Radio Removal ------------------------------------------------------ 1-2
2. Disassembly of the factory HVAC control module --------------------- 2-3
3. Assembly of the PAC HVAC control module ---------------------------- 3-4
4. RP5-GM4101 Instructions --------------------------------------------------- 4-6
5. AUX & USB Cable Installation ------------------------------------------------ 7
6. Temperature Display Settings ------------------------------------------------- 7
7. Sub-Dash Preparation ----------------------------------------------------------- 7
8. Kit Assembly Instructions ------------------------------------------------------- 8
9. Installation of the PAC HVAC control module --------------------------- 8-9
Page 2
RPK5-GM4101
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2010-2015 Chevrolet Camaro
PAC® | 866-931-8021 | support@pac-audio.com
©2016 Pacic Accessory Corporation
www.pac-audio.com Rev. 113016
P ifi A C ti
PAC is an AAMP power brand
Disassembly of the factory HVAC control panel
The following steps will aide you in the disassembly of the HVAC control panel so that the factory
HVAC control knobs and supports can be reused in the PAC RPK5-GM4101 Integrated Kit.
2.6 - Be sure to keep the screws
separated as there are different lengths
and diameters.
2.5 - Using a at bladed pry tool remove two
of the white fasteners off of the black plastic
backing.
2.4 - Remove the 10 Phillips head screws
shown below and remove the black plastic
backing.
2.2 - Pry outwards on the clips on either side
of the plastic trim that surrounds the white
connector.
2.3 - Once the plastic trim is removed, locate
the 16 pin connector shown below. Using a
at bladed tool, press in the grooves on both
sides, pry upward and away from the circuit
board, to release the connector.
2.1 - Remove the 2 Phillips head screws
shown below.
1.3 - Remove the 4 x 7mm bolts (1) securing the radio
(2) into the dash. Slide the radio (2) to the rear and
disconnect all electrical connections.
You can set the radio aside as it will not be used fur-
ther. For the next section, you will be working with
the factory HVAC control panel to utilize the HVAC
knobs allowing for more of a factory experience
when using the PAC RPK5-GM4101.
Proceed to the next section to begin disassembly of
the factory radio control assembly.
Removing the factory radio from the vehicle (cont.)
Page 3
PAC® | 866-931-8021 | support@pac-audio.com
©2016 Pacic Accessory Corporation
www.pac-audio.com Rev. 113016
P ifi A C ti
PAC is an AAMP power brand
RPK5-GM4101
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2010-2015 Chevrolet Camaro
Disassembly of the factory radio control assembly (cont.)
2.7 - Remove the 12 Phillips head screws
shown below.
2.8 - Be sure to keep the screws separated
as they will be used during the assembly
stage later.
2.9 - After the screws have been removed,
remove the HVAC knobs by pulling them
from the front of the faceplate being careful
not to bend the contacts on either end of the
contact swiper on the backside of each of
the knobs.
2.10 - Look inside the opening where the
knobs were removed. Remove the 2 Phillips
screws shown below. Do this for both
openings.
2.11 - Remove the 2 support brackets and
keep handy as they will be used in the next
step.
Assembly of the PAC HVAC control assembly
3.2 - Secure the 2 support brackets to
the circuit board using the same screws
removed from Disassembly step # 9. The
screws will pass through the board and
thread into the brackets via the holes dened
below. Be sure that the alignment tabs are
seated properly.
3.1 - Secure the 2 support brackets to the
PAC HVAC control assembly using 4 of the
same screws shown in disassembly step #
7. Do this to the back of each side. Be sure
that the alignment tabs are seated properly
in the circuit board to the front.
3.3 - Position the knobs in the proper opening
so that the buttons are straight and insert
them into the opening. With VERY LITTLE
force rotate them slightly left and right while
pushing them towards the PCB. Once the
alignment tabs are lined up they should click
and lock into place. Use extra caution as the
contacts could bend while rotating.

Specyfikacje produktu

Marka: PAC
Kategoria: zestaw samochodowy
Model: RPK5-GM4101

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PAC RPK5-GM4101, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje zestaw samochodowy PAC

PAC

PAC RPK4-CH4103 Instrukcja

16 Września 2024
PAC

PAC RPK5-GM4101 Instrukcja

12 Września 2024

Instrukcje zestaw samochodowy

Najnowsze instrukcje dla zestaw samochodowy

Metra

Metra 99-7367HG Instrukcja

8 Października 2024
Metra

Metra 99-8223 Instrukcja

8 Października 2024
Metra

Metra 99-7422 Instrukcja

8 Października 2024
Metra

Metra 99-7875 Instrukcja

8 Października 2024
Metra

Metra 99-3302 Instrukcja

8 Października 2024
Metra

Metra 99-5802 Instrukcja

8 Października 2024
Metra

Metra 99-7874 Instrukcja

8 Października 2024
Metra

Metra 99-5832G Instrukcja

8 Października 2024
Metra

Metra 99-9011 Instrukcja

8 Października 2024
Metra

Metra 99-6000 Instrukcja

8 Października 2024