Instrukcja obsługi PAC RP4-MZ11

PAC Niesklasyfikowane RP4-MZ11

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC RP4-MZ11 (7 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/7
RP4-MZ11
Radio Replacement & Steering Wheel Control Interface
for MazdaVehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2012 Pacic Accessory Corporation
www.pac-audio.com
Rev. 081612
C
Page 1
Introduction & Features
Important Notes
The RP4-MZ11 interface allows the replacement of a factory radio in select Mazda vehicles with MS-CAN radios. Using
this interface will retain factory features such as steering wheel controls (SWC), programming of the clock on the OEM
LCD screen, vehicle information on the OEM LCD screen and the BOSE amplier when the original radio is removed. The
RP4-MZ11 also provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS),
illumination, reverse trigger and parking brake.
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see below for setting chart).
2. If using this interface in a Mazda CX-5, all vehicle settings must be nalized before removing the factory radio.
3. When the interface is rst plugged into the vehicle the LED will ash indicating that it is initializing. Once initialization is complete
the LED will illuminate and should be on at all times when the interface is on.
4. The following vehicles will not provide a VSS signal as this information is not on the data bus: RX-8, 2007-2009 CX-9 w/non-nav
radio, Miata
5. The following vehicles will not provide a reverse output as this information is not on the data bus: RX8, 2007-2009 CX7, 2010
Mazda 5, Miata
6. The following vehicles will not provide a parking brake output as this information is not on the data bus: RX-8, Miata
7. The following vehicles have a speed based parking brake wire that will provide a negative trigger until the vehicle is going at
least 4 mph: 2007-2009 CX-9, 2007-2009 CX-7
8. The LED will also ash whenever a SWC button is pressed
9. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing
and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
10. The LED will ash whenever a SWC button is pressed.
Wiring Connection Chart
Red / White P.B. Output (-)
Purple / White VSS Output
Red Acc. Output (1 amp)
Green/ White 2nd SWC Input
(Connect to blue
wire in vehicle con-
nector in Mazda
CX-5, not used in
other applications)
Green Reverse Output (+)
Orange Illumination
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
(connect to Green/
White wire in inter-
face connector in
the Mazda CX-5)
Orange/White Illumination
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector SWC Connector
Blu/Yel Kenwwod, Newer
JVC, OEM or
Blaupunkt
3.5mm Jack Alpine, JVC,
Clarion, Pioneer,
Sony, Fusion, Valor,
Boyo, Dual, Visteon
or Advent
RP4-MZ11
Radio Replacement & Steering Wheel Control Interface
for Mazda Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2012 Pacic Accessory Corporation
www.pac-audio.com
C
Rev. 081612
Page 2
Installation Steps
1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle.
2. Make all connections as described in the chart on page 1. Connect the blue wire in the 24 pin vehicle harness to the 2013+ Mazda CX5 -
green/white wire in the 16-pin RP harness. This is necessary for the Bluetooth SWC to function with the aftermarket radio. This vehicle must
also use the orange/white wire in the Interface Connector.
3. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input).
4. If you wish to reassign the SWC buttons to different functions follow the programming instructions in the next section.
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Fusion OEMClarion JVC Kenwood Pioneer Valor
1 7 8 9 2 3 6 7 54
1
2
3
4
5
6
7
8
9
0
Illustration / Schematic
Pacific Accessory Corporation
Interface Connector
See above chart for
wire color descriptions.
Vehicle Connector
See above chart for
wire color description.
SWC Connection
See above chart for
different radio type
connections
Wiring SWC Connection
The interface comes pre-programmed for the functions listed in the chart below and does not require programming unless you
wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing the
program button on the side of the interface once and waiting for the LED to ash four times.
Alpine JVC Kenwood Clarion
V
alo
r
OEM Sony/Pionee
r
Fusion Blaupunkt
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Mode Source Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Next Track + Track + Track +
Track - Track - Track - Track - Search - Track - Previous Track - Track - Track -
V
oice/Mute Mute Mute Mute Mute Mute Mute Mute Mute Mute
Answe
r
Receive Receive Answer Send Cursor + Answer Answer Audio Disc +
End End Selec
t
Pla
y
End OK Hang Up Phone Menu Powe
r
OK
Optional Steering Wheel Control Programming
Default SWC Button Assignments
RP4-MZ11
Radio Replacement & Steering Wheel Control Interface
for MazdaVehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2012 Pacic Accessory Corporation
www.pac-audio.com
Rev. 081612
C
Page 3
Radio Alpine JVC Kenwood Clarion Valor OEM
Advent, Boyo, Dual,
Visteon, Sony Pioneer Blaupunkt Fusion
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
3 Mute Mute Mute Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Source Source Preset + Preset + Source Source
5 Preset - Track + Play Search + Track + Next Preset - Preset - Track + Track +
6 Source Track - Track + Search - Track - Previous Source Source Track - Track -
7 Track + Band/Disc + Track - Band Up Cursor Play/Ok Track + Track + Disc + Audio
8 Track - Preset/Disc - Disc/FM + Send/End Down Cursor Band Track - Track - Disc - Power
9 Power Select Disc/AM - Send Ok Up Cursor Band Band Ok
10 Enter/Play Attenuation Answer End Down Cursor Phone Menu
11 Band/Program Phone Receive BT Answer Answer Call
12 Receive Phone Reject BT Hangup End Call
13 End Voice Dial Voice Activation
14 Power
SET RADIO SELECT SWITCH
1
2
3
4
5
6
7
8
9
0
If you wish to re-assign the SWC functions, the interface must be programmed in the specic order shown in the chart below. If you
come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release the
program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have successfully
skipped that function and are ready to proceed to the next one.
Optional Programming Order
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Fusion OEMClarion JVC Kenwood Pioneer Valor
1 7 8 9 2 3 6 7 54
Optional Steering Wheel Control Programming (Cont)

Specyfikacje produktu

Marka: PAC
Kategoria: Niesklasyfikowane
Model: RP4-MZ11

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PAC RP4-MZ11, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane PAC

PAC

PAC RP4-GM31 Instrukcja

8 Października 2024
PAC

PAC NU-GM51 Instrukcja

8 Października 2024
PAC

PAC NAV-1129 Instrukcja

8 Października 2024
PAC

PAC LP7-2R Instrukcja

8 Października 2024
PAC

PAC LP7-4 Instrukcja

8 Października 2024
PAC

PAC GMK367B Instrukcja

8 Października 2024
PAC

PAC CP1-FRD1 Instrukcja

8 Października 2024
PAC

PAC C2A-CHY5 Instrukcja

8 Października 2024
PAC

PAC NU-GM3 Instrukcja

8 Października 2024
PAC

PAC CP1-TSL1 Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024