Instrukcja obsługi PAC APSUB-TY13

PAC Niesklasyfikowane APSUB-TY13

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC APSUB-TY13 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev: 2
Date: 052721
®
Advanced Subwoofer Amplier Interface
for Select Toyota and Lexus Applications
APSUB-TY13
The APSUB-TY13 provides a 2-channel non-fading output for use with an aftermarket amplier and subwoofer. Using the
full range, xed level head unit output, in conjunction data bus messages, the APSUB-TY13 delivers a variable 5v RMS
pre-amp output with bass equalization and level control capabilities. The signal has a 350Hz / 24dB Linkwitz-Riley low
pass lter applied. A data controlled remote amplier turn on wire is also provided by the APSUB-TY13.
Introduction and Features
Important Notes
1. Only compatible in vehicles equipped with a data bus controlled premium sound system. To verify compatibility in Toyota,
look for a JBL logo on the radio. In Lexus, compatible applications will have a center channel or factory subwoofer.
2. Toyota Safety Connect / Lexus Enform (SOS) audio mute can be retained. See the page 3 for detailed instructions.
3. The factory radio's speed controlled volume, DSP, and surround sound mode are not supported by the APSUB outputs.
4. Thefactoryampliermustremainconnected,andinthevehicleaftertheAPSUBhasbeeninstalled.
5. The radio's minimum volume level is set to 0 dB by default. If you are happy with this level in your particular application,
additionaladjustmentisnotrequired.PleaserefertotheSetupandCongurationsectiononpage3formoredetails.
6. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.
7. The subwoofer channels are non-fading outputs. The output level of subwoofer channels can be controlled using the
supplied level control knob.
Wiring Connection Chart
To Aftermarket
Amplier
Subwoofer Outputs
Non-Fading
Level Control
Knob
Remote Turn On Output (2A Max)
SOS Mute ( - Trigger Input )
GRAY GRAY
BLACK BLACK
28-pin
10-pin
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 2
Rev: 2
Date: 052721
®
Advanced Subwoofer Amplier Interface
for Select Toyota and Lexus Applications
APSUB-TY13
Installation
1. Remove the factory radio.
2. Disconnect the 28-pin harness and the 10-pin connectors from the
radio.
3. Ensure that you only remove the 28-pin connector that is closest
to the 10-pin connector, the correct 28-pin connector will be either
gray or white depending on the vehicle. There is another 28-pin
connector on the radio that will not be used. See Figure 1.
4. Connect the APSUB harnesses to the vehicle harnesses.
5. Connect the APSUB harnesses to the factory radio.
6. Set any feature DIP switches that apply to your install:
a DIP switch 1 is not used and should remain off (up).
b. Set DIP switch 2 on (down) to lower the RCA output voltage to 4v.
Leave DIP switch 2 off (up) to keep the RCA output voltage at 5v.
c. *Set DIP switch 3 on (down) to increase the input gain for the
vehicles listed on Page 3. All others, leave DIP switch 3 off (up)
to keep the input gain at the default value.
d. DIP switch 4 is not used and should remain off (up).
7. Connect the APSUB harness to the module.
8. Connect the level control knob to the module and install in an
accessible location.
9. Connect the signal cables and remote input from the aftermarket
amplier.
10. The Yellow / Black "SOS Mute" wire will be used in conjunction with
the Safety Connect / Lexus Enform (SOS) Retention. See Page 3
for more details.
DIP
1234
ON
Not Used 5v / 4v Preout Input Gain Setting* Not Used
1 2 3 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
Module Layout
LED 1
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection
Subwoofer Outputs
LED 2
Fig.1
10-pin 28-pin NOT USED
The aftermarket amplier must have a very solid ground and the amplier power/ground
connections should be made before connecting the RCA's or Remote Turn On
to the APSUB-TY13
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 3
Rev: 2
Date: 052721
®
Advanced Subwoofer Amplier Interface
for Select Toyota and Lexus Applications
APSUB-TY13
Installation (cont.)
DIP Switch 3 Conguration
For the vehicle models listed below, DIP switch 3 should be set to ON (down). These vehicle models have been found to have
a lower audio voltage output from the radio than that of other model vehicles. Setting DIP Switch 3 to ON (down) will increase
the input gain of the APSUB to accommodate this lower audio voltage from the radio and enable the APSUB to produce the
proper 5v of audio output when installed into these model vehicles.
Safety Connect / Lexus Enform (SOS) Retention
In order to retain the factory feature of muting the radio's audio while
an SOS call is taking place, the Yellow / Black "SOS Mute" must be
connected to the Telematics Mute Trigger wire in the vehicle. The
Telematics Mute trigger wire is in the white 24pin connector at the
factoryamplier(referenceconnectorimageandpinlocation).A
military splice connection to this wire will be adequate.
12 11 10 9 8 7 6 5 4 3 2 1
24 23 22 21 20 19 18 17 16 15 14 13
WIRE SIDE
WHITE
NOTE! Do not set DIP switch 3 ON (down) if your vehicle model is not listed above. Doing so will cause the APSUB's audio
output to clip at all volume levels.
Toyota 4Runner
Toyota Camry
Toyota Tundra
Toyota Sequoia
SetupandConguration
1. Prior to testing, cycle the ignition on and off to properly initialize the APSUB-TY13.
2. Turn the ignition on. LED 1 on the interface will turn on and the +12v remote output will turn on.
3. Set the amp gain(s) to the desired level. We recommend using an oscilloscope and test tones to set the amp gain(s).
Please refer to the MECP Advanced study guide if you are unfamiliar with this process.
4. Check volume, balance, fade and EQ settings.
5. If you would like to adjust the radio's minimum volume, do so using one of the methods outlined below. If you are happy with
the default levels, no adjustments are necessary.
Manually Setting the Minimum Volume
If the minimum volume of the radio (factory radio volume level 1) is too loud, you can manually set the level of the minimum
volume using the programming button. If you would like to set the minimum volume using the AmpPRO app, please proceed to
the AmpPRO App section.
PLEASE NOTE: Level control knob must be connected to the module in order to set the Minimum Volume.
Setting the minimum volume using the programming button
1. Set the amp gains to the desired level.
2. Start with the level control knob turned all the way down (counter-clockwise).
3. Set the volume on the factory radio to 1.
4. Press the programming button on the side of the interface once.
5. LED 1 will turn amber.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
DIP
1 2 3 4
ON

Specyfikacje produktu

Marka: PAC
Kategoria: Niesklasyfikowane
Model: APSUB-TY13

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PAC APSUB-TY13, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane PAC

PAC

PAC APSUB-TY13 Instrukcja

28 Grudnia 2024
PAC

PAC RP4-GM31 Instrukcja

8 Października 2024
PAC

PAC NU-GM51 Instrukcja

8 Października 2024
PAC

PAC NAV-1129 Instrukcja

8 Października 2024
PAC

PAC LP7-2R Instrukcja

8 Października 2024
PAC

PAC LP7-4 Instrukcja

8 Października 2024
PAC

PAC GMK367B Instrukcja

8 Października 2024
PAC

PAC CP1-FRD1 Instrukcja

8 Października 2024
PAC

PAC C2A-CHY5 Instrukcja

8 Października 2024
PAC

PAC NU-GM3 Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

GBC

GBC ThermaBind T500Pro Instrukcja

15 Stycznia 2025
Da-Lite

Da-Lite Parallax 29850 Instrukcja

15 Stycznia 2025
Crivit

Crivit IAN 290909 Instrukcja

15 Stycznia 2025
Tripp Lite

Tripp Lite SmartRack SRW12US Instrukcja

15 Stycznia 2025
Powerfix

Powerfix IAN 280221 Instrukcja

15 Stycznia 2025
AGM

AGM Rattler TC35-640 Instrukcja

15 Stycznia 2025
AGM

AGM Wolf-7 Pro Instrukcja

15 Stycznia 2025
AGM

AGM Anaconda TC50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Secutor Pro TS50-640 Instrukcja

15 Stycznia 2025
Microchip

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025