Instrukcja obsługi PAC RP4-CH11

PAC Niesklasyfikowane RP4-CH11

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC RP4-CH11 (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Rev. 112811
Introduction & Features
Important Notes
Wiring Connection Chart
Illustration / Schematic
The RP4-CH11 interface allows the replacement of a factory radio in select Chrysler/Dodge/Jeep vehicles with MSCAN or
LSFT-CAN databus radios. Using this interface will retain factory features such as steering wheel controls (SWC) vehicle
entertainment system (VES) and the factory audio amplier whenever the original radio is removed. The RP4-CH11 also
provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination,
reverse trigger and parking brake.
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see next page for setting chart).
2. When the interface is rst plugged into the vehicle the LED will ash indicating the auto detect sequence. Once the CAN-BUS
speed is detected the LED will illuminate and should be on at all times when the interface is on. The LED will also ash whenever
a SWC button is pressed
3. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing
and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
Red / White P.B. Output (-)
Purple / White VSS Output
Blue / White Amp Turn On Input
Red Acc. Output (1 amp)
Orange / White Illum. Output (+)
Green Reverse Output (+)
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector SWC Connector
Blu/Yel Kenwwod, Newer
JVC, OEM or
Blaupunkt
3.5mm Jack Alpine, JVC,
Clarion, Pioneer,
Sony, Valor, Boyo,
Dual, Visteon or
Advent
Accessory Output
+12volts 1amp max.
Interface Connector
See above chart for
wire color descriptions.
Vehicle Connector
See above chart for
wire color description.
SWC Connection
See above chart for
different radio type
connections
Wiring SWC Connection
Page 1
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Rev. 112811
Optional Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming
unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by
pressing the program button on the side of the interface once and waiting for the timeout.
SET RADIO SELECT SWITCH
Installation Steps
1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle (see page 2 for setting chart).
2. Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your
particular vehicle.
3. Make all connections as described in the connection chart on page 1. Vehicles without a factory amplier: Connect the aftermarket radio’s
front and rear speaker wires to the vehicle connector. Vehicles with a factory amplier: The factory amplier only accepts two channels
of audio input (left and right). Connect the front outputs of the aftermarket radio to the rear inputs of the vehicle connector. This will allow
navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used. Fading is not
supported in this application. The factory amplier’s fading is controlled by data communication from the factory radio. Neither the aftermarket
radio or the RP interface have the ability to control the amplier’s fader.
4. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input)
5. If you wish to reassign functions to the SWC follow the programming instructions in the next section.
If you wish to re-assign the SWC functions, the interface must be programmed in the specic order shown in the chart on the next
page. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have
successfully skipped that function and are ready to proceed to the next one.
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
Default SWC Button Assignments
Alpine JVC Kenwood Clarion
V
alo
r
OEM Sony/Pionee
r
Blaupunkt
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Source Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Next Track + Track +
Track - Track - Track - Track - Search - Track - Previous Track - Track -
Preset + Preset + Preset Disc/Radio + Band Mute Band Preset + Disc +
V
oice Mute Mute Mute Mute Cursor - Answer Mute Mute
Phone Receive Receive
A
nswe
r
Send/End Cursor + Hang Up
A
nswe
r
OK
Page 2
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Rev. 112811
Alpine JVC Kenwood Clarion Valor OEM
A
dvent, Boyo, Dual,
Visteon, Sony Pioneer Blaupunkt
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
3 Mute Mute Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Source Source Preset + Preset + Source
5 Preset - Track + Play Search + Track + Next Preset - Preset - Track +
6 Source Track - Track + Search - Track - Previous Source Source Track -
7 Track + Band/Disc + Track - Band Up Cursor Play/Ok Track + Track + Disc +
8 Track - Preset/Disc - Disc/FM + Send/End Down Cursor Band Track - Track - Disc -
9 Power Select Disc/AM - Send Ok Up Cursor Band Band Ok
10 Enter/Play Attenuation Answer End Down Cursor Phone Menu
11 Band/Program Phone Receive BT Answer Answer Call
12 Receive Phone Reject BT Hangup End Call
13 End Voice Dial Voice Activation
14 Powe
r
Optional Programming Order
Optional Steering Wheel Control Programming (cont.)
Step B.
Press and
hold the
programming
button.
Step C.
Release the
programming
button. The
LED will turn
back on.
LED will turn off.
Step A.
Turn the vehicle ignition to
the ON position.
OFF
ACC
IGN
STRT
Step E.
Release the button.
The LED will turn on
back on.
Step D.
Within 7 seconds,
press and release the
button that is to be
learned on the steering
wheel.
The LED will
turn off during
this process.
VOL
VOL
Step F.
If you need to program more buttons,
repeat steps D & E for each additional
audio function on the steering wheel.
Program
remaining buttons
x4
Once programming is
completed, wait 7 seconds.
The LED will ash four
times indicating the end of
programming.
Step G.
After all buttons are
programmed
Page 3

Specyfikacje produktu

Marka: PAC
Kategoria: Niesklasyfikowane
Model: RP4-CH11

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PAC RP4-CH11, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane PAC

PAC

PAC APSUB-TY13 Instrukcja

28 Grudnia 2024
PAC

PAC RP4-GM31 Instrukcja

8 Października 2024
PAC

PAC NU-GM51 Instrukcja

8 Października 2024
PAC

PAC NAV-1129 Instrukcja

8 Października 2024
PAC

PAC LP7-2R Instrukcja

8 Października 2024
PAC

PAC LP7-4 Instrukcja

8 Października 2024
PAC

PAC GMK367B Instrukcja

8 Października 2024
PAC

PAC CP1-FRD1 Instrukcja

8 Października 2024
PAC

PAC C2A-CHY5 Instrukcja

8 Października 2024
PAC

PAC NU-GM3 Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

GBC

GBC ThermaBind T500Pro Instrukcja

15 Stycznia 2025
Da-Lite

Da-Lite Parallax 29850 Instrukcja

15 Stycznia 2025
Crivit

Crivit IAN 290909 Instrukcja

15 Stycznia 2025
Tripp Lite

Tripp Lite SmartRack SRW12US Instrukcja

15 Stycznia 2025
Powerfix

Powerfix IAN 280221 Instrukcja

15 Stycznia 2025
AGM

AGM Rattler TC35-640 Instrukcja

15 Stycznia 2025
AGM

AGM Wolf-7 Pro Instrukcja

15 Stycznia 2025
AGM

AGM Anaconda TC50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Secutor Pro TS50-640 Instrukcja

15 Stycznia 2025
Microchip

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025