Instrukcja obsługi PAC OS-5

PAC Niesklasyfikowane OS-5

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC OS-5 (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

OS-5

Radio Replacement Interface with

Telematics Retention

For select General Motors Vehicles

With 29 Bit Data Systems

PAC-audio.com

Rev: V1

Date: 12/17/2021 Page 1

Introduction and Features

Important Notes

1. Aftermarket radio must have an auxiliary input in order to retain RSE audio.

2. If the vehicle chimes when the radio is removed, the CMX is not necessary. In order to get the best possible sound out of the

CMX, please mount it in a place free and clear of any obstructions, preferably as close as possible to the bottom of the dash

pointing down toward the oor of the vehicle.

Module Layout

Programming Button

USB Port

Radio Select DIP switches

Interface Connector 4

Adjustment Dial

Module Status LED

USB Status LED

Interface Connector 1

Not Used

Interface Connector 2

Amplied Audio Output Connector 3

Non-Amplied Audio Output

The OS-5 interface allows the replacement of a factory radio in select General Motors vehicles with 29 Bit Data-Bus. Using this

interface will retain factory features such as Warning Chimes, Bose Amplier, Rear Seat Entertainment (RSE), and Rear Seat

Controls (RSC) when the original radio is removed. The OS-5 provides data bus driven outputs such as retained accessory power

(RAP), vehicle speed signal (VSS), illumination, reverse trigger and parking brake.

OS-5

Radio Replacement Interface with

Telematics Retention

For select General Motors Vehicles

With 29 Bit Data Systems

PAC-audio.com

Rev: V1

Date: 12/17/2021 Page 2

Installation Steps

1. Wire your aftermarket radio to the OS-5’s harness according to the wiring connections chart below.

2. The Brown mute loop in Interface Connector 4 (if not cut) will turn the OS-5’s accessory output off when any OnStar

function is active. If the aftermarket radio has a mute input, cut this loop and connect the Brown wire in pin 23 to it. This pin

is located in the top row next to the solid blue wire. (The top of the connector has the locking tab on it).

3. Plug Interface Connectors 1 and 2 into the appropriate ports on the OS-5 interface (using the diagram on Page 1 or the

label on the bottom of the interface).

4. The Connector 3 connection will be dependent upon whether or not the vehicle has a factory amplied system. Plug this

connector into the appropriate port on the OS-5 (using the diagram on Page 1 or the label on the bottom of the interface).

5. If the aftermarket radio is equipped with an auxiliary input and you wish to retain the factory RSE audio, you must use the

part# GMRVD (Sold Separately).

6. Remove the factory radio and plug in the OS-5’s Vehicle and Vehicle Connector 1 Connector 2 into the factory vehicle

harness.

7. Plug the 2-Pin connector into the CMX Chime Module (If the vehicle chimes when the radio is removed, the CMX is not

necessary). PLEASE NOTE: In order to get the best possible sound out of the CMX, please mount it in a place free and clear

of any obstructions, preferably as close as possible to the bottom of the dash pointing down toward the oor of the vehicle.

Interface Connector 1

(3-pin)

Interface Connector 2

(20-pin)

Interface Connector 4

(24-pin)

Interface Connector 3

(12-pin)

Yellow 12v+

Red Accessory Output

(10 amp)

Black Ground

Brown Loop Mute Output

Blue Not Used

Blue / White Remote On Input

Orange Not Used

Orange / White Illumination Output

Purple / White Reverse Output (+)

Light Green Parking Brake Output (-)

Pink Vehicle Speed Signal

(VSS) Output

Blue / Yellow SWC Output / Key 1

Brown SWC Output / Key 2

3.5 mm Jack SWC Output

Purple Rear R + input

Purple / Black Rear R - input

Green Rear L + input

Green / Black Rear L - input

Gray Front R + input

Gray / Black Front R - input

White Front L + input

White / Black Front L - input

Wiring Connections

CMX Chime Module

Vehicle Connector 1

(14-pin)

Vehicle Connector 2

(16-pin)

OS-5

Radio Replacement Interface with

Telematics Retention

For select General Motors Vehicles

With 29 Bit Data Systems

PAC-audio.com

Rev: V1

Date: 12/17/2021 Page 3

Programming Button and Adjustment Dial Functions

You can press and hold the programming button on the side of the interface to access different programming modes. Once the

LED is lit to the mode you desire (see below for modes), immediately release the programming button to access that mode.

PLEASE NOTE:

• This process must be done with the interface in the vehicle and the key in the ignition position.

A. LED 1 ash red: Master reset. This does a master reset of the interface and restores the following settings to factory

defaults:

• SWC Mapping

• SWC Calibration

SWI-DIRECT Steering Wheel Control Output Connector

If you are using the SWI-RC-1 or SWI-CP2 please follow the steps below.

Refer to the gure to the right to set the bank of eight Dip-Switches.

Refer to the guide below for setting the bank of four Dip-Switches based on your radios manufacturer.

Set DIP-Switches that correspond with your radio to the ON position.

Set all other DIP-Switches to the OFF position.

If your brand is not listed above, please use “ALL OTHER BRANDS.”

Alpine JVC

Kenwood /

Lightning

Audio

Stinger Clarion /

Nakamichi

All Other

Brands Pioneer Sony Fusion

1 2 1 & 2 3 3 1, 2, & 3 1, 2, & 3 4 1 & 4

Testing and Verication

1. Turn the ignition on. LED 1 will illuminate red and the +12v accessory wire will turn on.

2. Turn on the radio and check chimes, volume, balance, and fader.

3. In vehicles equipped with Premium Bose (Y91 / UQA): If the overall volume is too low, use the adjustment dial on the side of

the interface to set it to the desired level. The best way to do this is to turn the volume on the radio to 3/4 volume, then turn the

adjustment dial on the OS-5 clockwise until some distortion is heard, then

counter-clockwise a little.

4. To adjust OnStar volume, press the OnStar button on the mirror then use the

volume buttons on the SWC, or the adjustment dial on the side of the module

to adjust the level. When you hear a chime during this process it means you

have reached the farthest minimum / maximum level.

5. Pressing the OnStar button on the rearview mirror will turn off the rear speakers

and allow the OnStar audio to be heard in the two front speakers. The OnStar

active LED will also turn on. When OnStar disconnects, the radio will un-mute

or turn back on and the OnStar LED will turn off. Pressing the VR / OnStar

button on the steering wheel will also activate OnStar.

6. Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes or until any door is opened.

7. The LED and radio will turn off when RAP turns off or until any door is opened.

8. Use the 4-position selector switch located on the side of the CMX chime module to select the best chime output volume for your

specic installation. Setting 1 being loudest and 4 being softest.

CMX

chime module

OnStar Volume Adjustment for Vehicles without SWC

Adjustment Dial

1. When OnStar is active use the adjustment dial on the side

of the module to raise or lower the OnStar volume to the

desired level.

Specyfikacje produktu

Marka:	PAC
Kategoria:	Niesklasyfikowane
Model:	OS-5

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PAC OS-5, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane PAC

PAC RP4-GM31 Instrukcja

8 Października 2024

PAC NU-GM51 Instrukcja

8 Października 2024

PAC NAV-1129 Instrukcja

8 Października 2024

PAC LP7-2R Instrukcja

8 Października 2024

PAC LP7-4 Instrukcja

8 Października 2024

PAC GMK367B Instrukcja

8 Października 2024

PAC CP1-FRD1 Instrukcja

8 Października 2024

PAC C2A-CHY5 Instrukcja

8 Października 2024

PAC NU-GM3 Instrukcja

8 Października 2024

PAC CP1-TSL1 Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024