Instrukcja obsługi PAC OnStar OS-3

PAC Niesklasyfikowane OnStar OS-3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC OnStar OS-3 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Pacifi c Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com Page 1
10-15-07
The OS-3 is a plug and play interface that allows replacement of a General Motors GMLAN factory radio. It will maintain
operation of the OnStar® system. The OS-3 has on board switching and audio amplifi ers which allow audio from the
OnStar® system to play through the two front factory speakers when OnStar® is active. This interface retains all warning
chimes, the audible turn signal indicators, rear seat radio control buttons (when optional SWI interface is used) and the
Vehicle Rear Parking Assist System (if equipped).
Step 1- Pre wire the OS-3RAD wire harness to the aftermarket stereo wire harness.
Step 2- After connecting the OS-3RAD and OS-GM14 wire harness to the OS-3 main interface, connect the OS-GM14 connector to the
factory harness.
The Following General Motors Vehicles using the GMLAN Data Bus WITHOUT a Bose® Amplifi er.
Pontiac: Torrent (2007)
Saturn: Outlook (2007)
GMC: Acadia (2007) Yukon Denali (2007) Yukon (2007) Sierra - not classic (2007) Sierra Denali - not classic (2007)
Cadillac: Escalade - including ESV and EXT (2007) SRX (2007) DTS (2007)
Buick: Lucerne (2006-2007)
Chevrolet: Suburban (2007) Tahoe (2007) Avalanche (2007) Monte Carlo (2006-2007) Silverado - not classic (2007) Impala (2006-2007)
Equinox (2007)
1. The OS-3 does not retain the factory XM receiver. You will lose the XM option when the factory radio is replaced with an aftermarket
radio.
2. If you are not retaining the OnStar® system, use the C2R-GM29 instead of this OS-3 interface.
3. Built in Smart Mute Circuitry will play OnStar® audio through the front speakers while muting the radio or turning the radio off if a mute
input circuit is not present
• OnStar® active LED and Ignition on LED.
• Provides +12v switched accessory output. No more searching for switched +12v in fuse box or kick panel.
• Steering wheel radio controls can be retained to control the new radio by using the SWI - X, JACK, ECL2 or PS.
• New radio will operate with the vehicle RAP (Retained Accessory Power) circuit. The radio stays on after the key is turned off and stays on
for approximately 10 minutes or until the drivers door is opened.
Note: Connect the Purple/White wire (pin 18) from the OS-3RAD to the radios mute input. If a mute input is not available, connect the
Purple/White wire (pin 18) to the Red/White wire (pin 16) of the OS-3RAD connector. The Lt. Green wire is a SWC output wire. Do not con-
nect this wire to anything other than the green interface wire of a SWI - X, JACK, ECL, or PS. Program the SWC interface for version #2 and
DO NOT CUT the Brown SWI interface loop. When pushing the steering wheel buttons during programming, a simple press and release
of the button will do just fi ne, no need to hold. The rear controls (if equipped) will perform the same functions as the steering wheel buttons
without any additional programming necessary. If steering wheel controls are not retained or present, isolate this wire and do not use!
Wire locations and Description
WIRE COLOR CIRCUIT CIRCUIT WIRE COLOR
9 18
8 17
7 16
6 15
5 14
4 13
3 12
2 11
1 10
PIN NUMBER
SWC Output
Chime Module
White/Black
Grey/Black
Green/Black
Purple/Black
Black
Lt. Green
Orange
Blue/White
Red
Left Front(-)
Right Front (-)
Left Rear (-)
Right Rear(-)
Ground
Illumination
Amp Turn On
+12v Accessory Output
Left Front (+)
Right Front (+)
Left Rear (+)
Chime Module
Right Rear (+)
+12v Constant
White
Grey
To CM - X
Green
To CM - X
Purple
Yellow
Purple/White
Red/White
Mute Sense
Mute Output
WIRE COLOR CIRCUIT CIRCUIT WIRE COLOR
Orange Illumination
8 16
Purple/White GMLan
7 15
+12v Constant Yellow
Black Ground
6 14
Amplifier Turn On Blue
Purple/Black Right Rear (-)
5 13
Right Rear (+) Purple
Green/Black Left Rear (-)
4 12
Left Rear (+) Green
OnStar Mono(-)
3 11
OnStar Mono(+)
Grey/Black Right Front (-)
2 10
Right Front (+) Grey
White/Black Left Front (-)
1 9
Left Front (+) White
PIN NUMBER
Purple/WhiteWhite/Brown
Amp Control Black
OS-3RAD
OS-GM14
Notes
Supported Vehicles
Installation
1
1
0 0
0
0
0
0
1
1
1
0
0
1
1
1 0
0
0
0
0 0
0
1
1
0
0
1
0
0
0
1
0
1
0 0
0 0
1
0
1 0
1
0 0
1
C
l
C
a
1
0
OS-3
General Motors OnStar®
Interface Installation Instructions
for GMLAN Vehicles Without Bose®
Pacifi c Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com Page 2
Step 3- The CM-X should be plugged into the white 2-pin connector and permanently mounted. This module will retain all warning chimes
and audible turn signal indications. There is no volume adjustment for this feature so keep that in mind when choosing a mounting
location.
Step 4- The OnStar volume is controlled from the adjustment screw on the interface. Make sure this is set to the desired level before ®
mounting the interface and reassembling the dash. The OS-3RAD speaker inputs will not be used
Note - This confi guration is used when aftermarket amplifi er(s) are installed to power new or existing speakers. You can also use this con-
fi guration when the Bose® amplifi er is “Bypassed” in the vehicle.
Step 3- The CM-X should be plugged into the white 2-pin connector and permanently mounted. This module will retain all warning chimes
and audible turn signal indications. There is no volume adjustment for this feature so keep that in mind when choosing a mounting
location.
Step 4- The OnStar volume is controlled from the adjustment screw on the interface. Make sure this is set to the desired level before ®
mounting the interface and reassembling the dash.
102.7 FM
Aftermarket stereo
30
8586
87
87a
Red wire to accessory
input of radio
c2
c1
OS - GM14 Harness
OnStar
Active
®
Volume
Adjust
OS - 3
General Motors GMLan OnStar Interface®
Factory Radio Replacement
Retention the OnStar Option®
Ignition
On LED
Pacific Accessory Corporation Santa Ana, Ca 92705
OS-3RAD
CM-X
O
Chime Module
SWC output wire
Connect to SWI - X green wire
Program for Version # 2
L
t
G
r
e
e
n
W
i
r
e
Connecting to the Vehicle’s Factory Speakers
Connecting to External Speakers
102.7 FM
Aftermarket stereo
30
85
86
87
87a
Red wire to accessory
input of radio
c2
c1
OS - GM14 Harness
OnStar
Active
®
Volume
Adjust
OS - 3
General Motors GMLan OnStar Interface®
Factory Radio Replacement
Retention the OnStar Option®
Ignition
On LED
Pacific Accessory Corporation Santa Ana, Ca 92705
OS-3RAD
(-)(+) (-)(+)
White
White/Black Grey
Grey/Black
High Power
Speaker Outputs
Are Not Used
CM-X
O
Chime Module
SWC output wire
Connect to SWI - X green wire
Program for Version # 2
L
t
G
r
e
e
n
W
i
r
e
Audio Signal
to new amp(s)
Testing and Verifying Operation
1. Turn ignition on. The red ignition On LED inside the interface will turn on and the +12v accessory wire will turn on.
2. Turn on the radio and check balancing and fading.
3. Pressing the OnStar® button will turn off the radio (or mute it depending on the connections made) and allow the OnStar® audio to be
heard in the two front speakers. The OnStar® active red LED will also turn on. When OnStar® disconnects, the radio will un-mute or turn
back on and the OnStar® LED will turn off.
4. Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes or until the drivers door is opened.
5. The red LED and the radio will turn off when RAP turns off or the drivers door is opened.
6. Pressing the Mute/OnStar® button on the steering wheel for 1.5 seconds will activate Onstar®.
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the OS-3 be held liable for consequential damages sustained
in connection with the OS-3. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to
assume obligation or liability in relation to the OS-3 other than its replacement.
OnStar® is a registered trademark of OnStar® Corporation.
Bose® is a registered trademark of Bose®

Specyfikacje produktu

Marka: PAC
Kategoria: Niesklasyfikowane
Model: OnStar OS-3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PAC OnStar OS-3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane PAC

PAC

PAC RP4-GM31 Instrukcja

8 Października 2024
PAC

PAC NU-GM51 Instrukcja

8 Października 2024
PAC

PAC NAV-1129 Instrukcja

8 Października 2024
PAC

PAC LP7-2R Instrukcja

8 Października 2024
PAC

PAC LP7-4 Instrukcja

8 Października 2024
PAC

PAC GMK367B Instrukcja

8 Października 2024
PAC

PAC CP1-FRD1 Instrukcja

8 Października 2024
PAC

PAC C2A-CHY5 Instrukcja

8 Października 2024
PAC

PAC NU-GM3 Instrukcja

8 Października 2024
PAC

PAC CP1-TSL1 Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024