Instrukcja obsługi PAC GM1A-RT

PAC Niesklasyfikowane GM1A-RT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC GM1A-RT (5 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/5
GM1A-RT
Radio Replacement Interface with
Telematics Retention
for select General Motors Vehicles
with Class II Data-Bus
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: V6
Date: 0 18927
Page 1
Important Notes
Module Layout
Programming Button
USB PortInterface Connector 4
Adjustment Dial
Interface Connector 1
Expansion Port
Interface Connector 2
The GM1A-RT interface allows the replacement of a factory radio in select General Motors vehicles with the Class II Data-Bus.
Using this interface will retain factory features such as OnStar, warning chimes and the factory Bose amplier when the original
radio is removed. The GM1A-RT provides data bus driven outputs such as retained accessory power (RAP), vehicle speed signal
(VSS), illumination, reverse trigger and parking brake. The GM1A-RT also provides an SWI Direct output for adding an optional
PAC Steering Wheel Control (SWC) retention interface (SWI-RC or SWI-CP2). Rear Seat Controls (RSC) if equipped will also
be retained with the SWI interface. You can also add multiple camera inputs to your aftermarket radio with Data-Bus controlled
automatic activation (front camera only) by connecting a VS41 into the expansion port on the GM1A-RT.
Introduction and Features
1. The included chime speaker should be used when: The vehicle has a standard Bose system (UQ7), the vehicle does not have
a factory amplier at all, or if you are connecting an aftermarket amplier to the cabin speakers.
2. The Programming Button and Adjustment Dial on the side of the interface have multiple functions. Please see Page 3 for
more details.
3. Compatible in both Premium Bose (Y91 / UQA) and Standard Bose systems.
4. Real time speaker fading on Premium factory amplied systems (UQA / Y91) is only supported with the “amplied output”
connection of the GM1A-RT.
5. When using real time speaker fading (Premium Bose only), if the fader setting is biased more to the front or rear, as the radio
turns on the sound may begin at the default setting and then quickly transition to your custom setting.
6. Aftermarket radio features such as High Pass Filters (crossovers), DSP or “Network Mode” will interfere with proper fader
function (Premium Bose Only). In order for the GM1A-RT’s fader function to work, the audio from the aftermarket radio’s
output must match so it can compare the front and rear audio levels and determine the proper fader setting for the factory
amplier.
7. When used in conjunction with the add on camera controller (VS41) the GM1A-RT will only provide Data-Bus controlled
automatic activation for the front camera. Please refer to the vehicle specic VS41 instructions for more detail.
Interface Connector 3
Non-Amplied
Audio Output
LED 1
LED 2
Amplied
Audio Output
GM1A-RT
Radio Replacement Interface with
Telematics Retention
for select General Motors Vehicles
with Class II Data-Bus
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: V6
Date: 0 18927
Page 2
Interface Connector 1
(3-pin)
Interface Connector 2
(20-pin)
Interface Connector 3
(12-pin)
Interface Connector 4
(24-pin)
Vehicle Connector 1
(24-pin)
Vehicle Connector 2
(12-pin)
Installation Steps
1. Wire your aftermarket radio to the GM1A-RT’s harness according to the wiring connections chart below.
2. Plug Interface Connectors 1 and 2 into the appropriate port on the GM1A-RT interface (using the illustration on page 1 or the
label on the bottom of the interface).
3. The Brown mute loop in Interface Connector 4 (if not cut) will turn the GM1A’s accessory output off when any OnStar
function is active. If the aftermarket radio has a mute input, cut this loop and connect the Brown wire in pin 23 to it.
4. The Connector 3 connection will be dependent upon whether or not the vehicle has a factory amplied system. Plug this
connector into the appropriate port on the GM1A-RT (using the illustration on page 1 or the label on the bottom of the
interface).
5. If the aftermarket radio is equipped with an auxiliary input and you wish to retain the factory RSE audio, plug the RCA
connectors from the secondary harness into the radios auxiliary input.
6. If you are also installing an optional SWC interface with the GM1A-RT, connect the SWI Direct Connector to the SWC
interface.
7. Remove the factory radio and plug in the GM1A-RT’s Vehicle Connector 1 and Vehicle
Connector 2 into the factory vehicle harness.
8. If necessary, program the SWC interface.
9. If you are connecting an aftermarket amplier to the cabin speakers, connect the
chime speaker to the chime plug coming out of Interface Connector 4 and install
the chime speaker in a place free of obstructions, where it can be easily heard
(usually low in the dash facing downward).
Yellow 12v+
Red Accessory Output
(10 amp)
Black Ground
Brown Loop Mute Output
Blue Not Used
Blue / White Remote On Input
Orange Not Used
Orange / White Illumination Output
Purple / White Reverse Output (+)
Light Green Parking Brake Output (-)
Pink Vehicle Speed Signal
Output (VSS)
Purple Rear R + input
Purple / Black Rear R - input
Green Rear L + input
Green / Black Rear L - input
Gray Front R + input
Gray / Black Front R - input
White Front L + input
White / Black Front L - input
Wiring Connections
Steering Wheel Control Output Connector
Fig. A
1. The GM1A-RT provides a SWC output connector labeled “Connect to PAC Steering Wheel Control Interface”
(Fig. A). For ease of installation, all necessary connections have been made for you.
2. You can use either a PAC SWI-RC or an SWI-CP2 (sold separately).
a. When using an SWI-RC, the loop on the output connector should remain intact. Set the
SWI-RC to version two and program the buttons according to the SWI-RC instructions.
b. When using an SWI-CP2, use the DIP switch settings provided for the GM1A-RT in the
ControlPRO application. The steering wheel controls will be preconfigured for the vehicle
and radio but can be customized using the ControlPRO PC application. The loop on the
output connector should remain intact.
VS41 Wiring
The VS41 can be connected to the GM1A-RT and used to switch multiple cameras. Please refer to the document labeled
“Instructions for wiring the VS41 into 2003-2006 Chevy / GMC Trucks and SUVs” which can be found on www.pac-audio.
com under the VS41 product page.
GM1A-RT
Radio Replacement Interface with
Telematics Retention
for select General Motors Vehicles
with Class II Data-Bus
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: V6
Date: 0 18927
Page 3
Programming Button and Adjustment Dial Functions
You can press and hold the programming button on the side of the interface to access different programming modes. Once the
LED is lit to the mode you desire (see below for modes), immediately release the programming button to access that mode.
PLEASE NOTE:
• This process must be done with the interface in the vehicle and the key in the ignition position.
•If there is a Premium Bose system, and you are also installing an amplier on the cabin speakers, make sure that
the chime speaker is connected and chimes are enabled through the RadioPRO app before proceeding. Please see
the RadioPRO app section on Page 4 for more details.
A. Corvette only2 Chimes and LED1 ash amber: SWC re-calibration (this mode is available in the ).This allows you to
re-calibrate the analog SWC in the event they fall out of the expected range and do not function properly. If data control
SWC are detected by the interface, this mode will be automatically skipped.
B. Chime volume adjustment.3 Chimes and both LEDs ash green: This allows you to adjust the volume of the
chimes generated by the interface using the adjustment dial on the side. This mode is not available in vehicles equipped
with Premium Bose (Y91 / UQA) amps. If a Premium Bose amp is detected by the interface, this mode will be skipped
as the factory amp is what generates the chimes. Please see the vehicles owner’s manual for adjustment of chime
volume in vehicles with Premium Bose (Y91 / UQA).
C. Master reset.4 Chimes and LED 1 ash red: This does a master reset of the interface and restores the following
settings to factory defaults:
• SWC Calibration
• Camera Settings
• Infotainment Settings
• Interface User Options
1. Turn the ignition on. LED 1 will illuminate red and the +12v accessory output will turn on.
2. Turn on the radio and check chimes, volume, balance, and fader.
3. In vehicles equipped with Premium Bose (Y91 / UQA): If the overall volume is too low, use the adjustment dial on the
side of the interface to set it to the desired level. The best way to do this is to turn the volume on the radio to 3/4 volume,
then turn the adjustment dial on the GM1A-RT clockwise until some distortion is heard, then counter-clockwise a little.
4. If an SWI interface was also installed, verify that all SWC buttons are functioning properly. If you are installing the GM1A-RT
into a Corvette, and are experiencing erratic SWC behavior, you may need to follow the SWC re-calibration procedure in
the next section.
5. Pressing the OnStar button on the rearview mirror will turn off the rear speakers and allow the OnStar audio to be heard in
the two front speakers. Pressing the VR / OnStar button on the steering wheel will also activate OnStar.
6. Turn off vehicle and remove key. RAP will keep the radio on for 10 minutes or until any door is opened.
7. LED 1 will turn off when RAP turns off.
Testing and Verication
Adjustable Settings
These products have settings that are adjustable through our RadioPRO PC app or through the push-button on the module.
Some settings are only adjustable through the PC app. Some of these settings require the module to be connected to the
vehicle. Below is a breakdown of these settings.
CONNECTED TO CAR NOT CONNECTED TO CAR
Chime volume (excluding Premium Bose Y91/UQA) YES NO YES
Factory amplifier settings:
Bass, Mid, Treble, Gain, and Fade
(Premium Bose Y91/UQA only)
YES NO GAIN ONLY
OnStar volume (RST or RT products only) YES NO YES
Read product version YES YES N/A
Update firmware YES YES N/A
Camera settings (VS41 required) YES YES NO
AVAILABLE ON PC APP
AVAILABLE ON MODULESETTING
Related Downloads
• RadioPRO PC App: http://aampglobal.com/radioproapp
• Latest instruction manuals: Search part number on pac-audio.com, and then look under the “Downloads” tab

Specyfikacje produktu

Marka: PAC
Kategoria: Niesklasyfikowane
Model: GM1A-RT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PAC GM1A-RT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane PAC

PAC

PAC RP4-GM31 Instrukcja

8 Października 2024
PAC

PAC NU-GM51 Instrukcja

8 Października 2024
PAC

PAC NAV-1129 Instrukcja

8 Października 2024
PAC

PAC LP7-2R Instrukcja

8 Października 2024
PAC

PAC LP7-4 Instrukcja

8 Października 2024
PAC

PAC GMK367B Instrukcja

8 Października 2024
PAC

PAC CP1-FRD1 Instrukcja

8 Października 2024
PAC

PAC C2A-CHY5 Instrukcja

8 Października 2024
PAC

PAC NU-GM3 Instrukcja

8 Października 2024
PAC

PAC CP1-TSL1 Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024