Instrukcja obsługi PAC C2R-CHY4

PAC Niesklasyfikowane C2R-CHY4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC C2R-CHY4 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Pacic Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
7-19-10
J1850
Class 2
VPW
Class 2
J1850
100011101111001001101100
111010000110110111001100
EOD
CRC
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
Radio Replacement Interface
with Nav Outputs for all Chrysler
Dodge / Jeep CANbus Vehicles With
or Without Premium Audio Systems
C2R-CHY4
1. Only one of the two provided radio harnesses will be used. Remove the factory
installed radio to determine the correct harness for your particular vehicle.
2. Vehicles without a factory amplier: Connect the aftermarket radio’s front and
rear speaker wires to the 22 pin plug.
3. Vehicles with a factory amplier: The factory amplier only accepts two audio
channels (left and right). The amplier’s fading is controlled by data communication
from the factory radio. The aftermarket radio does not have the ability to control the
amplier’s fader. Connect the front outputs of the aftermarket radio to the rear inputs of the 22 pin radio connector. This will
allow navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used.
4. The accessory output wire is located on the 11 pin CAN INTERFACE harness - connect this wire to the radio’s accessory wire. The
accessory wire supplies +12v, 1 amp max when key is in the accessory or ignition position (g. 1: If more current is needed).
5. 11 pin plug (to CAN INTERFACE):
Blue/White - Connect this wire to the radio’s amplifier remote output. Connect this wire with or without OEM amp present!1.
White/Green - SWC output.2.
Green - Connect this wire to the radio’s reverse input wire only.3.
Orange/White - Connect this wire to the radio’s Illumination input wire only.4.
Violet/White - Connect this wire to the radio’s VSS input wire only.5.
Red/White - Connect this wire to the radio’s parking brake input wire only.6.
Note: Do not connect these wires to any circuit other than the radio’s wire harness.
6. 11 pin plug (to SWC INTERFACE):
This is a quick connection to a radio specic SWC interface. No additional
connections are necessary other than radio control connections. Plug the radio
specic SWC interface in to this connector and program the radio specic SWC
interface for version 2. Do not cut the loops. Refer to the SWC interface instruction
manual for the radio specic control function programming order.
7. Refer to the aftermarket radio’s instruction manual for testing VSS, Reverse, Parking Brake and Illumination outputs. For the most
current and Up-to-Date application guide please visit www.pac-audio.com
Fig. 1
(using a SPDT relay)
85 86
30
87
87a
Ground
High Current 12v
(Fused)
12v Acc.
From
Interface
New High
Current Output
Diode 1N4005
or equivelant
9
1
23456
78
1011
Accessory Output
+12volts 1amp max.
Ch
9 1
9
1
23456
78
1011
9 1
SWC Interface.
Program for Version 2
Radio Specific Steering
Wheel Control Interface
(Sold Separately)
Program SWC
Interface for Version 2.
CAN INTERFACE
Navigation outputs and
Amplifier Remote Input
See Chart for wire color
descriptions.
Radio Connections. See aside
Chart for color description.
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
(Read the Installation Notes before making
connections to the provided radio harness)
CAN Interface Connection Chart:
Red Acc. Output (1 amp)
Red / White P.B. Output (-)
Purple / White VSS Output (Pulse)
Orange / White Illum. Output (+)
Green Reverse Output (+)
White / Green SWC Output
Blue / White Amp Turn On Input
Installation Notes
Radio Connection Chart
Pacic Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
7-19-10
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2R-CHY4 be held liable for consequential damages sustained in
connection with the C2R-CHY4. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume
obligation or liability in relation to the C2R-CHY4 other than its replacement.
Using the VES & Reverse Camera (if equipped)
Vehicles equipped with a DVD player built into the rear screen assembly:
The C2R-CHY4 will allow the VES DVD player and rear screen to function as if the factory radio were present. A/V will be passed
from the factory DVD player to the rear screen and audio can be heard through the headphones. A/V cannot be passed from the
factory DVD player to the aftermarket head unit.
Vehicles equipped with a stand alone VES DVD Player:
The C2R-CHY4 will allow the VES DVD player and rear screen(s) to function as if the factory radio were present. A/V will be
passed from the factory DVD player to the rear screen(s) and audio can be heard through the headphones. A/V can also be fed
from the VES DVD player into an aftermarket head unit (head unit must support A/V in) with the use of the CHYRVD.
Vehicles not equipped with a VES DVD Player (rear screen(s) only):
In this application the CHYRVD must be used in order to feed A/V into the factory screen(s) from an aftermarket head unit (head
unit must support A/V out). With the CHYRVD, A/V will be passed from the aftermarket head unit to the rear screen(s) and audio
can be heard through the headphones. If you wish to retain the Auxiliary inputs on the rear of the console you must disconnect the
factory wires from the auxiliary input then connect and run your own RCAs into the aftermarket head unit.
Vehicles equipped with a Reverse Camera:
In order to retain the factory reverse camera the CHYRVD must be used to feed video into the aftermarket head unit (head unit
must support reverse camera input).

Specyfikacje produktu

Marka: PAC
Kategoria: Niesklasyfikowane
Model: C2R-CHY4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z PAC C2R-CHY4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane PAC

PAC

PAC RP4-GM31 Instrukcja

8 Października 2024
PAC

PAC NU-GM51 Instrukcja

8 Października 2024
PAC

PAC NAV-1129 Instrukcja

8 Października 2024
PAC

PAC LP7-2R Instrukcja

8 Października 2024
PAC

PAC LP7-4 Instrukcja

8 Października 2024
PAC

PAC GMK367B Instrukcja

8 Października 2024
PAC

PAC CP1-FRD1 Instrukcja

8 Października 2024
PAC

PAC C2A-CHY5 Instrukcja

8 Października 2024
PAC

PAC NU-GM3 Instrukcja

8 Października 2024
PAC

PAC CP1-TSL1 Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024