Instrukcja obsługi Ozito PXTSS-018
Ozito
Szlifierki orbitalne
PXTSS-018
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito PXTSS-018 (11 stron) w kategorii Szlifierki orbitalne. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/11
STANDARD EQUIPMENT
PXTSS-018
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 18V
No Load Speed: 12,000/min
Oscillating Speed: 24,000/min
Paper Size: 184 x 92mm (1/3 Sheet)
Paper Fitment: Clamp or Hook & Loop
Adaptor Size: Ø35mm
Weight: 1.21kg
ozito.com.au
0620
Cordless 1/3 Sheet Sander
80 Grit Sandpaper, Paper
Punch Plate, Dust Bag & Dust
Extraction Adaptor
CORDLESS 1/3
SHEET SANDER
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Sandpaper Selection
Selecting the correct grit of sandpaper is an important step in achieving
optimum results. Coarse grit will remove the most material. Finer grit will
produce a smoother nish. The condition of the workpiece will determine
the grit of the sandpaper to be used. The higher the grit number, the ner
the grade of sandpaper.
If the surface is rough, start with a coarse grit and sand until the surface
is uniform. Medium grit may then be used to remove scratches left by the
coarser grit. Finer grit is then used to nish the surface. Always continue
sanding with each grade of sandpaper until the surface is uniform.
MATERIAL
APPROPRIATE GRIT
Coarse
Sanding Fine Sanding
Paintwork 180 400
Wood: Softwood 60 240
Hardwood 60 180
Veneer 240 320
Note: If intermediate sanding is required, choose a grit rating between
coarse and ne. The above table is intended as a guide only. To ensure a
satisfactory result, a small, inconspicuous area should rst be tested to
ensure the grit of sandpaper chosen is suitable for the desired nish.
Using Hook & Loop Sandpaper
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
Use this method of paper tment with the supplied sheet of 80 grit
sandpaper. Replacement sanding sheets with hook & loop backing can also
be attached via this method.
1. Align the holes on the
sanding sheet with the holes
on the sanding pad.
2. Press the hook & loop side of
the sandpaper rmly against
the sanding pad.
This tool is compatible with all batteries & chargers from the Ozito Power X Change
range.
CORDLESS 1/3 SHEET SANDER
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. SANPAPER FITMENT
SETUP & PREPARATION
4
6
5
3
1
2
789
1. On/Off Switch
2. Wire Clamp
3. Palm Grip Handle
4. Battery Seating
5. Dust Extraction Port
6. Dust Extraction Adaptor
7. Sanding Pad
8. Sandpaper
9. Spring Clamp Handle
Specyfikacje produktu
| Marka: | Ozito |
| Kategoria: | Szlifierki orbitalne |
| Model: | PXTSS-018 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Ozito PXTSS-018, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Szlifierki orbitalne Ozito
1 Lipca 2024
Instrukcje Szlifierki orbitalne
- Szlifierki orbitalne Festool
- Szlifierki orbitalne Black & Decker
- Szlifierki orbitalne DeWalt
- Szlifierki orbitalne Einhell
- Szlifierki orbitalne Makita
- Szlifierki orbitalne Zenit
- Szlifierki orbitalne Güde
- Szlifierki orbitalne Ferm
- Szlifierki orbitalne HiKOKI
- Szlifierki orbitalne Skil
- Szlifierki orbitalne Maktec
- Szlifierki orbitalne Pattfield
Najnowsze instrukcje dla Szlifierki orbitalne
13 Października 2024
9 Października 2024
9 Sierpnia 2024
8 Sierpnia 2024
6 Lipca 2024
6 Lipca 2024
5 Lipca 2024
5 Lipca 2024
4 Lipca 2024
4 Lipca 2024