Instrukcja obsługi Ozito PXCLTK-218
Ozito
Podcinacze
PXCLTK-218
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito PXCLTK-218 (8 stron) w kategorii Podcinacze. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE
WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING
YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER
SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer service helpline
above.
0316
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other
than that specied on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty. Warranty excludes consumable parts, for example: cutting blades.
CORDLESS GRASS
TRIMMER KIT
INSTRUCTION MANUAL
SPECIFICATIONS
Voltage: 18V
Battery: 2.0Ah Li-ion
Charge Time: 2.5 Hours
No Load Speed: 8,500/min
Cutting Diameter: 240mm
Weight: 2.2kg
PXCLTK-218
WHAT’S IN THE BOX
Grass Trimmer
ozito.com.au
Blades x 10
2.0Ah Battery & Eco Charger
ONLINE MANUAL
Scan this QR Code with your mobile
device to take you to the online
manual.
Fitting the Adjustable Handle
1. Fit the handle mounting bracket
onto the upper section of the shaft.
Note: You will need to carefully ex
the mounting bracket just enough to
slip over the shaft. Do not over ex as
this can damage or break the mounting
bracket.
2. Place the adjustable handle on
the mounting bracket, then pass
the screw with washer through
the mounting bracket and onto the
adjustable handle lever.
14 15 16 17 18
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
1. Extend the edging guide to allow
the safety guard to go over the
spindle.
3. Slide in until it clicks into place.
2. Align the tabs of the
safety guard with the
recess in the back of the
cutter head.
Fitting the Safety Guard
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND BATTERY DISCONNECTED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
WARNING! NEVER USE THE GRASS TRIMMER
UNLESS THE SAFETY GUARD IS PROPERLY FITTED.
CORDLESS GRASS TRIMMER
1
10
2
11
3
12
4
13
5
6
7
8
9
1. Telescopic Shaft
2. Shaft Adjustment Collar
3. Adjustable Handle Lever
4. Adjustable Handle
5. Lock-off Switch
6. Rear Handle
7. On/Off Trigger
8. Battery Seating
9. Head Tilt Button
10. Edging Guide
11. Cutter Head
12. Safety Guard
13. Cutting Blade
ACCESSORIES
19
14. Battery Release Tab
15. Battery Charge LED’s
16. Battery Charge Indicator Button
17. Charger
18. Charger LED
19. Blades x 10
2. ADJUSTING THE TRIMMER
1. Release the adjustable handle
lever.
1. Place the big hole in the blade
onto the blade mount on the
bottom of the spindle plate.
3. To remove the blade push the
blade towards the centre of the
spindle and then slide off.
1. Press and hold the head tilt
button.
2. Tilt the cutter head to the desired
angle.
2. Rotate the head into the desired
position.
3. Ensure the head has clicked
into a secure position before
operating.
3. Ensure the head has clicked
into a secure position before
operating.
1. Pull the telescopic shaft away
from the cutter head.
The grass trimmer head has 2 adjustments to allow for the optimal angle and
position for grass trimming or edging.
1. Loosen the shaft adjustment
collar.
2. Rotate the handle into
the desired position and
then lock in place with
the lever.
2. Pull the blade outwards
so that the small hole is
tted into the mount.
2. Extend to the desired
height and then
retighten the shaft
adjustment collar to
secure in place.
Adjusting the Handle
Adjusting the Cutter Head
Head Tilt Head Angle
Adjusting the Height
Attaching a Blade
Specyfikacje produktu
| Marka: | Ozito |
| Kategoria: | Podcinacze |
| Model: | PXCLTK-218 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Ozito PXCLTK-218, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Podcinacze Ozito
6 Lipca 2024
4 Lipca 2024
4 Lipca 2024
Instrukcje Podcinacze
- Podcinacze Worx
- Podcinacze Stihl
- Podcinacze Parkside
- Podcinacze Black & Decker
- Podcinacze Makita
- Podcinacze Fuxtec
- Podcinacze RYOBI
- Podcinacze ATIKA
- Podcinacze Hitachi
- Podcinacze Shindaiwa
- Podcinacze Spear & Jackson
- Podcinacze McCulloch
- Podcinacze Tanaka
- Podcinacze Krausmann
- Podcinacze Dolmar
- Podcinacze McGregor
- Podcinacze Pattfield
- Podcinacze Maruyama
Najnowsze instrukcje dla Podcinacze
13 Października 2024
13 Października 2024
12 Października 2024
12 Października 2024
9 Sierpnia 2024
9 Sierpnia 2024
8 Sierpnia 2024
8 Sierpnia 2024
8 Sierpnia 2024
8 Sierpnia 2024