Instrukcja obsługi Oyen Digital Mobius
Oyen Digital
dysk twardy
Mobius
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Oyen Digital Mobius (2 stron) w kategorii dysk twardy. Ta instrukcja była pomocna dla 24 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Mobius 5-Bay RAID System
User Guide
(11) Warranty Information
This product includes a two (2) year repair/replacement
warranty provided by Oyen Digital. This warranty is non-
transferable and is limited to the original purchaser. Warranty
service may be requested by completing the form at the
following link: www.oyendigital.com/rma-request-form.html
For our complete warranty policy, visit:
www.oyendigital.com/warranty.html
(9) Ejecting the Mobius
Windows: Close all applications that are accessing the Mobius.
Click the “Eject Hardware” (Safely Remove) icon in the system tray
and select the Mobius. The LEDs will cycle o/on a few times
and the HDDs will spin down. The LEDs and HDDs will remain o
when it is fully dismounted. : In JBOD mode, individual drivesNote
cannot be ejected separately. All drives must be ejected.
Mac: Close all windows and applications that are accessing the
drive. Drag the Mobius to the Trash/Eject icon to dismount it.
The LEDs will cycle o/on a few times and the HDDs will spin down.
The LEDs and HDDs will remain o when it is fully dismounted.
(10) Frequent Asked Questions (FAQs)
1) If the system experiences an HDD failure:
The LED for the HDD will be solid red/purple and the sounder
will beep (press SET to silence).
2) Can I remove a drive from the RAID and install it in
another enclosure for access to the les?
You can do so for RAID 1 or JBOD. In other modes, you cannot
remove a single drive and access it outside of the RAID.
3) Can I create a RAID-5 and add additional drives later?
No. Once a RAID-5 set is created it must be cleared and re-created
to add or subtract drives from the set. This will delete all data.
4) Which drives are recommended for use with the Mobius?
We recommend enterprise or NAS drives such as WD Red or
Toshiba N300.
5) The Mobius’ LEDs icker on and then shut o when I turn
on the system. Why?
This indicates the Mobius is not receiving a handshake from the
computer. Check all connections making sure to connect directly
to a computer with the included cable.
6) I connected via eSATA but I only see one hard drive. Why?
It is due to the eSATA host not supporting “port multiplier” which
allows an eSATA port to communicate with more than one drive at
a time. We recommend the Sonnet Tempo cards, which include port
multiplier functionality.
Table of Contents
1 Specications
2 Detailed View
3 Inserting or Removing Drives
4 Setup
5 RAID Modes
6 Formatting
7 Sleep Mode
8 Rebuilding Data
9 Ejecting the Mobius
10 FAQs
11 Warranty Information
(6) Formatting
After setting a new RAID mode, you must format the volume
before it is accessible.
1. Connect the RAID to the computer.
2. Congure the desired mode as explained in section 4.
3. After the RAID is congured, use Disk Management on the PC
or Disk Utility on the Mac to format the volume *.
If using RAID 0 or RAID 5, we recommend performing a
low level format after setting the RAID.
Please refer to the following:
http://oyendigital.com/low-level-format
(8) Rebuilding Data
If one of the HDDs fails, the LED for the corresponding bay
will turn red/purple and the sounder will beep. Press the SET button
to stop the sound. A new HDD can be installed and it will
automatically rebuild with data (if congured as RAID 1, 3, 5, 10).
1. Power down the Mobius.
2. Remove the failed HDD.
3. Install the new HDD and power on the Mobius with it connected to
the computer. (The new HDD should be larger or equal to the
previous one.)
4. The LED will blink about 2-3 times per second, which indicates a
rebuild in progress.
5. You may disconnect the Mobius from the computer during the
rebuild, if desired. This will not interrupt the rebuild.
Notes:
• To estimate the rebuild time, multiply one HDD by 2 to get the
rebuild hours. For example, a 60TB RAID5 will take about 24 hours
(12TB x 2). This is approximate and will vary based on drive model.
• The RAID can be accessed during the rebuild, however, it may
increase the rebuild time.
(7) Sleep Mode
If there is no HDD activity, the OS may put the Mobius to sleep
(LEDs o, HDDs spin down). The Mobius will wake up when accessed.
Mac Users: the option “Put Hard Disks to Sleep When Uncheck
Possible” in the Energy Saver settings in System Preferences.
Windows Users: hard disk sleep and USB suspend in Disable
advanced power settings:
Control Panel > Power Options > Change Plan Settings > Change Advanced
Power Settings > Hard Disk > Turn o hard disk after = Never.
Control Panel > Power Options > Change Plan Settings > Change Advanced
Power Settings > USB Settings > USB Selective Suspend = Disabled.
To prevent conflict with the OS sleep commands, we
recommend disabling hard drive sleep in your OS as follows:
(5) RAID Modes
RAID 0 (Striping) is a non-redundant data mapping technique. It
combines data evenly across multiple drives simultaneously, increasing
performance.
• In Striping mode, it will be viewed as one single storage unit. If one
disk in the RAID System fails, all data in installed disks will be lost.
• The total capacity = smallest drive x the total number of drives. For
example, if the smallest drive is 1TB, the capacity will be 5 TB when 5
drives are installed.
RAID 1 (Mirroring) consists of two drives storing duplicate copies of
the same data. In this mode, the data is simultaneously written to two
disks. The speed of operation is slow in comparison to other RAID modes.
• Only 2 HDDs (bay 1 and 2) are allowed for the function to perform
properly.
RAID 5 uses block-level striping with parity data distributed across all
disks (RAID 5) or one disk (RAID 3). RAID 5 is the most common mode
due to the combination of redundancy and speed.
• A minimum of 3 drives is required. (See FAQ regarding adding
additional drives later)
• The total capacity = all disks minus 1. The capacity is limited by the size
of the smallest disk. For example, if three 2 TB and two 3 TB drives are
installed, the total capacity will be 8 TB ((2 TB x 5 disks) - 1 disk).
RAID 10 combines RAID 0 and RAID 1 in one single system. It creates
two sets of striped disks and then mirrors these sets.
• Only 4 HDDs are allowed for the function to perform. If 5 HDDs are
inserted, the 5th drive will be used as a hotspare, meaning when a drive
fails, the 5th drive will automatically be rebuilt to replace the failed drive.
Combine (Span) combines multiple hard drives into a single logical
unit. Unlike Striping, it writes data to the rst drive until it reaches full
capacity. When the rst disk reaches full capacity, data is written to the
second disk. Spanning provides the maximum possible storage capacity,
but does not increase performance or safety.
JBOD (Clear RAID) is not actually a RAID. It simply is a collection of
drives that are recognized as individual drives by the OS. JBOD provides
no performance increase or redundancy. This is the default setting.
(3) Inserting or Removing Drives
Inserting: Pull the lever to open the door. Insert/remove
drive into bay. To , pull the lever and push the door all the way close
closed. Release the lever when the door is closed.
Locking: Use the included key to lock the door if desired.
(4) Setup
Perform a “Clear RAID” procedure when installing drives for the rst
time. This procedure conditions the drives for use in the Mobius. It
does not delete the partition or data from individual drives.
Clear RAID Procedure:
Set the switches to Clear RAID (all switches down). Press and hold the
SET button and turn on the power. Continue to hold the SET
button until the 2nd beep occurs (approx. 10 seconds). Release the
SET button. Any previous RAID mode is removed and the drives are
now set for JBOD mode (individual drives).
You now may set a RAID mode, or leave in JBOD mode.
Press and hold SET button
and turn on the power.
Set the RAID switches to
the desired mode.
(JBOD)
RAID 1: Insert only 2 HDDs (Bay 1-2)
RAID 10: Insert 4 HDDs (Bay 1-4)
= Switch Position
Set RAID Mode:
To congure a RAID, set the switches to the desired mode. Press and
hold the SET button and turn on the power. Continue to hold the
SET button until the 2nd beep occurs (approx. 10 seconds). Release the
SET button. The RAID mode is now congured. : All previous dataNote
on the drives will be removed when setting a RAID mode.
We recommend using only enterprise or NAS drives (512e only). The
Mobius is not compatible with 4Kn hard drives.
10.5 x 5.1 x 7.4 inches
3.5” SATA HDD (NAS or Enterprise
recommended, 512e only)
Mac OS 10.4 or higher
Windows
RAID Modes RAID 0 Striping
RAID 1 Mirroring
RAID 10 Striping+Mirroring
RAID 3
RAID 5
CLEAR RAID (JBOD)
(1) Specications
1394b
FireWire 400 1394a
Supported Drives
Package Includes: Mobius 5-Bay, USB 3.0 cable, FW800 cable,
FW400 cable, eSATA cable, power cord, user guide, key set
LEDs and Sound:
Note: The drive LEDs will be OFF when the unit is not connected to a computer.
(2) Detailed View
1
2
3
3.Drive Bay
4. Voltage Select Switch
4
10
95
6
7
8
1211
Set the Mobius upright on its feet. The Mobius does not
function properly when laying on its side.
Solid red/purple; Sounder will beep (press SET to silence)
Rapid blinking purple
Off
Slow blinking purple (approximately 2-3 blinks per second)
Condition Drive LED
Drive Error
HDD Sleep / Eject
RAID 1 Rebuilding
Read/Write activity
Powered & ready Solid blue
Specyfikacje produktu
| Marka: | Oyen Digital |
| Kategoria: | dysk twardy |
| Model: | Mobius |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Oyen Digital Mobius, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje dysk twardy Oyen Digital
5 Października 2024
5 Października 2024
4 Października 2024
6 Maja 2024
Instrukcje dysk twardy
- dysk twardy Sony
- dysk twardy Samsung
- dysk twardy Pioneer
- dysk twardy Fujitsu
- dysk twardy StarTech.com
- dysk twardy Medion
- dysk twardy Toshiba
- dysk twardy Gembird
- dysk twardy Sandisk
- dysk twardy Dell
- dysk twardy Sabrent
- dysk twardy HGST
- dysk twardy Kingston
- dysk twardy Intenso
- dysk twardy Rocstor
- dysk twardy Western Digital
- dysk twardy Verbatim
- dysk twardy Sharkoon
- dysk twardy Apricorn
- dysk twardy Silverstone
- dysk twardy OWC
- dysk twardy AudioControl
- dysk twardy Transcend
- dysk twardy Areca
- dysk twardy Xcellon
- dysk twardy TrekStor
- dysk twardy Sandberg
- dysk twardy LaCie
- dysk twardy Fantec
- dysk twardy Sweex
- dysk twardy Seagate
- dysk twardy PNY
- dysk twardy G-Technology
- dysk twardy BLACKJET
Najnowsze instrukcje dla dysk twardy
9 Października 2024
8 Października 2024
7 Października 2024
6 Października 2024
6 Października 2024
5 Października 2024
5 Października 2024
5 Października 2024
4 Października 2024
4 Października 2024