Instrukcja obsługi OSD Audio Black BK-T61

OSD Audio głośnik Black BK-T61

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla OSD Audio Black BK-T61 (3 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

BLACK SERIES INSTALL GUIDE

Preparation:

Installation:

Tools For Installation Speaker Wire Guide

Considerations

Cut Out

Placement

- Pencil

- Drill

- Tape Measure

- Wire Cutter

- Phillips Screwdriver

- Utility Knife

- Safety Eye Wear

- Gloves

- Sandpaper

- Where is the best place to install the speakers?

- Where do the speakers sound the best?

- Separate the speakers 6 - 10 feet apart.

- ( ) Place speakers with the 15° For Ceiling LCR models only

angled woofer pointed towards the main listening area.

- If you intend to paint the grilles, do so before installation.

NOTE: This is the most important part of the entire installation.

If you are not certain whether any obstructions exist behind the

desired mounting area, you should start by cutting a small hole in

the center of your penciled mounting hole with a drywall saw.

Trace along the included template. Cut along the traced line using a

drywall saw or rotary drill. Use a piece of sandpaper to sand down the

cut out edge for a smoother contour. (See Diagram 2.)

There are many options for proper speaker placement depending

upon speaker type and application. It’s important to carefully plan the

placement of your speakers, as installation requires that you cut a

hole in your wall or ceiling.

(See Diagram 1.) Typical speaker placement for a 5.1 and 7.1

speaker system.

18AWG minimum - for distances up to …………………. 10 ft

16AWG - from …………………………………..…... 10 to 50 ft

14AWG - from …………………………………...… 50 to 100 ft

Diagram 2

Diagram 1

BLACK SERIES INSTALL GUIDE

Mounting

Connection

Adjustment

Pivoting Tweeter

Tighten the mounting brackets by simply turning the screws on

the front of the speaker bafe slowly clockwise. The quick-turn

mounting system and frame will “sandwich” or clamp around the

dry-wall to hold the speaker securely in place once fully tightened

to the locked position.

(See Diagram 3.)

When connecting any speakers to the amplier or receiver, always

make sure the power is off. Locate the connection terminals on the

back of your receiver or amplier. Always make sure to connect au-

dio out from the back of your receiver or amplier to the speakers.

(See Diagram 4.)

NOTE: Not all Amplier/Receivers can safely play more than one

pair of speakers at once. Please refer to your owner’s manual for

impedance and wattage compatibility.

On select models ( *Performance, Reference ) of OSD Black

Series, a front mounted 3 position ±3dB treble contour switch can

be used to tailor high frequencies according to speaker placement

or the listeners preference.

(See Diagram 5.)

* Excludes Shallow Mount Series

Your Black series speaker comes from the factory with the

tweeter centered in the neutral position. This will provide the

smoothest response. However, select models come with a

pivoting tweeter so you can focus the sound directly towards the

listening area if needed. In order to do this, carefully press on the

edge of the tweeter bafe in the direction you wish to focus the

sound. (See Diagram 6.)

CAUTION: When adjusting the pivoting tweeter be sure not to

touch the dome as you may cause damage to the speaker.

Left Out

Left Speaker

Rec/Amp

Right Out

Right Speaker

- -

+ +

Press Here to

Pivot Tweeter

Open PositionLocked Position

Diagram 3

Diagram 4

Diagram 5

Diagram 6

All Optimal Speaker Design speaker products have Limited Lifetime Warranty against defects in materials and workmanship. Proof

of purchase must accompany all claims. During the warranty period Optimal Speaker Design will replace any defective part and

correct any defect in workmanship without charge for either parts or labor Optimal Speaker Design may replace returned speakers

with a product of equal value and performance. In such cases, some modication to the mounting may be necessary and are not

Optimal Speaker Designs responsibility.

For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be

performed by Optimal Speaker Design. The unit must be returned to Optimal Speaker Design at the owner’s expense and with

prior written permission. Accidental damage and shipping damage are not considered defects, nor is damaged resulting from

abuse or from servicing performed by an agency or person not specically authorized in writing by Optimal Speaker Design

Optimal Speaker Design sells products only through authorized dealers and distributors to ensure that customers obtain proper

support and service. Any Optimal Speaker Design product purchased from an unauthorized dealer or other source, including

retailers, mail over dealers and on-line sellers will not be honored or serviced under existing Optimal Speaker Design warranty

policy. Any sale of product by an unauthorized source or other manner not authorized by Optimal Speaker Design shall void the

warranty on the applicable product.

Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases,

repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, you must email customer service

at RMA@audiogeargroup.com for a Returned Merchandise Authorization (RMA) number# then the unit must be shipped to

Optimal Speaker Design at the owner’s expense, along with a note explaining the nature of service required. Be sure to pack the

speaker(s) in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit.

This Warranty Does Not Cover: Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) •

Any products that have been altered or modied • Any product whose identifying number of decal, serial #, etc. has been altered,

defaced or removed • Normal wear and maintenance.

WARRANTY

Black Manual rev. 3/18

Specyfikacje produktu

Marka:	OSD Audio
Kategoria:	głośnik
Model:	Black BK-T61

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z OSD Audio Black BK-T61, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik OSD Audio

OSD Audio Nero ARC Sub Instrukcja

14 Stycznia 2025

OSD Audio Black BK-T61 Instrukcja

14 Stycznia 2025

OSD Audio Nero WLCR53 Instrukcja

27 Grudnia 2024

OSD Audio LS3 Instrukcja

19 Grudnia 2024

OSD Audio ACE840TT Instrukcja

9 Października 2024

OSD Audio SVC-100 Instrukcja

9 Października 2024

OSD Audio ICE630ST Instrukcja

9 Października 2024

OSD Audio LS2 Instrukcja

9 Października 2024

OSD Audio Black R63A Instrukcja

7 Października 2024

OSD Audio Black R83 Instrukcja

7 Października 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Edifier M1250 Instrukcja

14 Stycznia 2025

Samson RS10mHD Instrukcja

14 Stycznia 2025

Samson RSX115 Instrukcja

14 Stycznia 2025

TRENDnet TEW-ASAL1 Instrukcja

14 Stycznia 2025

TRENDnet TV-HP400 Instrukcja

14 Stycznia 2025

Exagerate XBTPET-PAN Instrukcja

14 Stycznia 2025

Exagerate XBTPET-PIG Instrukcja

14 Stycznia 2025

Exagerate XBTPET-OWL Instrukcja

14 Stycznia 2025

Ikarao Shell S1 Instrukcja

14 Stycznia 2025

Klipsch PIC-450-T Instrukcja

14 Stycznia 2025