Instrukcja obsługi Orion WB-4780

Orion Niesklasyfikowane WB-4780

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Orion WB-4780 (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
Tilt adjusting knob
INSTALLATION INSTRUCTIONS
ISSUED: OCT.2012
7
Tilting Wall Mount
4. Adjustment
3. Hang Display onto the Wall Plate
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
75kg
(165lbs)
MAX
Loose the adjusting knobs to tilt desired angle then tighten them.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
WB-4780
400x400/600x400
800x400/800x600 70"
MAX
0°
-10°
wall
Tighten bottom bolts to secure display brackets to the wall plate.
wall
Bolt
Premium Mount Inc
7300 Bolsa Ave., Westminster, CA 92683 -
Phone: 714-766-6303
2
Component Checklist
IMPORTANT: Ensu re tha t you ha ve rec eived all pa rts according to t he compon ent checklist pr ior to installin g. If
any parts are missing or f aulty, telephone your local distributor f or a replacement .
Package M
Package W
ST6.3x55 (x6)
W-A
concrete anchor (x6)
W-B
D6 washer (x6)
W-C
1
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any question
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experience and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
wall plate
A
(x1)
M5x14 (x4)
M-A
M6x14 (x4)
M-B
washer
M-F
(x4)
M8x20 (x4)
M-C
big spacer (x4)
M-H
M6x30 (x4)
M-D
M8x30 (x4)
M-E
small spacer (x8)
M-G
left (x1)adapter bracket
B
right (x1)adapter bracket
C
4
3
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
1a. Mount on Wood Stud Wall
• When installing wall mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting be used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
1b. Mount on Solid Brick and Concrete Block
W-C
Screw the wall
plate onto
the wall
Drill pilot holes
X X
√
1
2
3
Find and mark the
exact location of
mounting holes
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
55mm
55mm
55mm
2
2
2
2.
.
.
.2
2
2
2"
"
"
"
(
(
(
()
)
)
)
55mm
(2.2" )
X X
√
Screw the wall
plate onto
the wall
Drill pilot holes
1
2
Mark the exact
location of
mounting holes
60mm
(2.4")
60mm
60mm
60mm
60mm
2
2
2
2.
.
.
.4
4
4
4"
"
"
"
(
(
(
()
)
)
)
60mm
(2.4")
ø 10mm
(ø 3/8" )
W-A
W-C
W-B W-A

Specyfikacje produktu

Marka: Orion
Kategoria: Niesklasyfikowane
Model: WB-4780

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Orion WB-4780, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Orion

Orion

Orion 24RPE Instrukcja

8 Października 2024
Orion

Orion 22RPE Instrukcja

8 Października 2024
Orion

Orion WB-4780 Instrukcja

3 Października 2024
Orion

Orion CMA-02 Instrukcja

3 Października 2024
Orion

Orion WBLS Instrukcja

28 Września 2024
Orion

Orion 8FIDKR Instrukcja

28 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024