Instrukcja obsługi Optoma GT5500
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Optoma GT5500 (108 stron) w kategorii Projektor. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/108
1English
Table of Contents ............................1
Usage Notice ...................................2
Safety Information ...............................2
Precautions .........................................3
Eye Safety Warnings ..........................5
Product Features ................................5
Introduction ......................................6
Package Overview ..............................6
Product Overview ...............................7
Main Unit .............................................. 7
Control Panel ....................................... 8
Input/Output Connections .................... 9
Remote Control .................................. 10
Installation .....................................11
Connecting to the Projector ..............11
Connecting a Computer/Notebook .... 11
Connecting a Video source ................ 12
Connect to 3D Video Devices ...........13
Using the 3D glasses ........................15
Powering On/Off the Projector ..........16
Powering On the Projector ................. 16
Powering Off the Projector ................. 17
Warning Indicator ............................... 18
Adjusting the Projected Image ..........19
Adjusting the Projector’s Height ........19
Adjusting the Projector’s Focus ......... 20
Adjusting Projection Image Size ........ 20
User Controls ................................23
Control Panel & Remote Control ......23
Control Panel ..................................... 23
Remote Control .................................. 24
On-screen Display Menus ................27
How to operate .................................. 27
Menu Tree .......................................... 28
IMAGE ............................................... 35
IMAGE | Advanced ............................ 38
DISPLAY ............................................ 43
DISPLAY | 3D ................................... 48
SETUP ............................................... 50
SETUP | Audio Settings ..................... 53
SETUP | Security ............................... 55
SETUP | Network ............................... 57
SETUP | Network|LAN Settings ......... 58
SETUP | Network|Control Settings .... 60
SETUP | Signal (RGB) ....................... 70
SETUP | Signal (Video) ..................... 72
SETUP | Advanced ............................ 73
OPTIONS ........................................... 75
OPTIONS | Lamp Settings ................. 79
OPTIONS | Advanced ........................ 81
OPTIONS | Remote Settings ............. 83
OPTIONS | Filter Settings .................. 84
Appendices ....................................85
Troubleshooting ................................85
Image Problems ................................. 85
Other Problems .................................. 87
Remote Control Problems ................. 87
LED Lighting Messages ..................... 88
On Screen Messages ........................ 89
Replacing the Lamp ..........................90
Installing and Cleaning the
Dust Filter .........................................92
Compatibility Modes .........................93
RS232 Commands and
Protocol Function List .......................95
RS232 Pin Assignments .................... 95
RS232 Protocol Function List ............ 96
Ceiling Mount Installation ................104
Optoma Global Ofces ...................105
Regulation & Safety Notices ...........107
FCC Notice ...................................... 107
Declaration of Conformity for
EU countries .................................... 108
Table of Contents
2
English
Usage Notice
The lightning ash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous volt-
age” within the product’s enclosure that may be of sufcient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance (servic-
ing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian Inter-
ference-Causing Equipment Regulations.
Important Safety Instruction
1. Do not block any ventilation openings. To ensure reliable operation of the
projector and to protect from over heating, it is recommended to install the
projector in a location that does not block ventilation. As an example, do
not place the projector on a crowded coffee table, sofa, bed, etc. Do not
put the projector in an enclosure such as a book case or a cabinet that
restricts air ow.
2. Do not use the projector near water or moisture. To reduce the risk of re
and/or electric shock, do not expose the projector to rain or moisture.
3. Do not install near heat sources such as radiators, heaters, stoves or any
other apparatus such as ampliers that emits heat.
4. Clean only with dry cloth.
5. Only use attachments/accessories specied by the manufacturer.
6. Do not use the unit if it has been physically damaged or abused. Physical
damage/abuse would be (but not limited to):
Unit has been dropped. -
Power supply cord or plug has been damaged. -
Liquid has been spilled on to the projector. -
Projector has been exposed to rain or moisture. -
Something has fallen in the projector or something is loose inside. -
Do not attempt to service the unit yourself. Opening or removing covers
may expose you to dangerous voltages or other hazards. Please call
Optoma before you send the unit for repair.
7. Do not let objects or liquids enter the projector. They may touch danger-
ous voltage points and short out parts that could result in re or electric
shock.
8. See projector enclosure for safety related markings.
9. The unit should only be repaired by appropriate service personnel.
Safety Information
3English
Usage Notice
Please follow all warnings, precautions and mainte-
nance as recommended in this user’s guide.
When the lamp
reaches the end
of its life, the
projector will not
turn back on until
the lamp module
has been replaced.
To replace the
lamp, follow the
procedures listed
under “Replacing
the Lamp” section
on pages 90-91.
Warning- Do not look into the projector’s lens when the
lamp is on. The bright light may hurt your eyes.
Warning- To reduce the risk of re or electric shock, do
not expose this projector to rain or moisture.
Warning- Please do not open or disassemble the projec-
tor as this may cause electric shock.
Warning- When replacing the lamp, please allow the unit
to cool down. Follow instructions as described
on pages 90-91.
Warning- This projector will detect the life of the lamp
itself. Please be sure to change the lamp when
it shows warning messages.
Warning- Reset the “Lamp Reset” function from the on-
screen display “Options|Lamp Settings” menu
after replacing the lamp module (refer to page
79).
Warning- When switching the projector off, please ensure
the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the
projector to cool down.
Warning- When the lamp is approaching to the end of its
life time, the message “Lamp life exceeded.”
will show on the screen. Please contact your
local reseller or service center to change the
lamp as soon as possible.
Precautions
4
English
Usage Notice
Do:
Turn off and unplug the power plug from the AC outlet before
cleaning the product.
Use a soft dry cloth with mild detergent to clean the display hous-
ing.
Disconnect the power plug from AC outlet if the product is not be-
ing used for a long period of time.
Do not:
Block the slots and openings on the unit provided for ventilation.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
In extremely hot, cold or humid environments. -
Ensure that the ambient room temperature is within 5 `C ~
40 C
Relative humidity is 10% ~ 85% `
In areas susceptible to excessive dust and dirt. -
Near any appliance generating a strong magnetic eld. -
In direct sunlight. -
5English
Usage Notice
Avoid staring/facing directly into the projector beam at all
times. Keep your back to the beam as much as possible.
When projector is used in a classroom, adequately super-
vise students when they are asked to point out something
on the screen.
In order to minimize the lamp power, use room blinds to
reduce ambient light levels.
Eye Safety Warnings
Product Features
1080p (1920x1080)
XGA (1024x768) / WXGA (1280x800) Native resolution
HD compatible – 720p and 1080p supported
BrilliantColor TM Technology
Kensington Lock
RS232 control
Rapid shutdown
Full 3D (See page 94)
Crestron/Extron/ PJLink TM compatibility.
Eco+ mode for more economic usage
USB Power Charger
Interactivity Support (Only for Interactive version)
Product features
may vary depend-
ing on model.
6
English
Introduction
Optional
accessories vary
depending on
model, speci ca-
tion and region.
Unpack and inspect the box contents to ensure all parts listed
below are in the box. If something is missing, please contact
Optoma customer service.
Package Overview
Standard Accessories
Fre eze
Power S witch
L R
Keysto ne Vo lu me
Page
-
-
+
-
+
1 2
Me nu
3
3D
4
HD MI
5
V GA
6
V i deo
7
Us er1
8
Us er2
9
Us er3
Source
0
Resync
Page+Laser
Enter
Projector Power Cord Remote
CD User Manual
Warranty Card
Basic User Manual
2 × AAA Batteries Documentation
Laser Curtain Module
(for interactivity
version only)
Optional Accessories
HDMI Cable VGA Cable
For other laser
curtain accesso-
ries, please refer
to the laser cur-
tain user manual.
7English
Introduction
Product Overview
Main Unit
Do not block
projector in/out air
vents.
Lamp Cover1.
Control Panel2.
Focus Switch3.
IR Receiver4.
Input/Output Connections5.
Lens6.
Power Socket7.
Speaker8.
IR Camera (Only for 9.
interactive version)
21
6
5
4
3
7
9
8
8
English
Introduction
Control Panel
1 3 5
Power1.
Source2.
Lamp Indicator3.
Temperature (Temp) Indicator4.
IR Receiver5.
2 4
16
17 15 14
9English
Introduction
Input/Output Connections
Power Socket1.
Kensington2. TM Lock Port
RJ45 Connector3.
USB Power Connector (5V/2A Max.)4.
3D Sync Connector (5V)5.
RS-232C Connector (9-pin DIN Type) 6.
12V Audio Out Connector7.
USB Connector (Connect to PC for Remote Mouse 8.
function)
VGA-Out/VGA2-In Connector9.
VGA1-In/YPbPr Connector (PC Analog Signal/Component 10.
Video Input/HDTV/YPbPr)
Composite Video Input Connector11.
HDMI2 Input Connector12.
HDMI1 Input Connector13.
Audio 2 In Connector (3.5mm mini Jack)14.
Composite Audio Input (right/left) Connector15.
Audio Input Connector (microphone)16.
Audio Output Connector (3.5mm mini Jack)17.
Remote mouse
requires special
remote.
2 31
10 9 8
7654
11121314151617
10
English
Introduction
Remote Control
Power on / off1.
Freeze2.
Display blank / audio 3.
mute
Mouse left click4.
Enter5.
Laser6.
Page -7.
Keystone - / +8.
Menu9.
Aspect ratio10.
HDMI11.
User 212.
User 113.
Source14.
Brightness mode15.
Mouse on / off16.
Mute17.
Mouse right click18.
Four directional 19.
select keys
Page +20.
Volume - / +21.
3D menu on / off22.
VGA23.
Video24.
User 325.
Numeric keypad 26.
(0-9)
Re-sync27.
Some keys may
have no function
for models which
do not support
these features.
Freeze
Power Switch
L R
Keystone Volume
Page
-
-
+
-
+
1 2
Men u
3
3D
4
HDM I
5
VGA
6
Vid e o
7
Use r 1
8
Use r 2
9
Use r 3
Source
0
Resync
Page+Laser
Enter
4
1
2
3
5
6
13
10
8
7
9
11
12
14
15
27
20
16
17
18
22
23
24
21
26
19
25
11 English
Installation
Connecting a Computer/Notebook
Connecting to the Projector
Due to the
difference in
applications for
each country,
some regions may
have different
accessories.
(*) Optional
accessory
1.............................................................................................. RS-232C cable
2............................................................................ Remote Mouse USB cable
3....................................................................................VGA1-In/YPbPr cable
4...................................................................................................*HDMI cable
5.............................................................................................Audio 2 In cable
6.....................................................................................................Power cord
7............................................................................................. Audio Out cable
8..........................................................................Audio In (microphone) cable
9....................................................................................................RJ-45 cable
10......................................................................................... *3D emitter cable
11 ..............................................................................VGA-Out/VGA2-In cable
E62405SP
R
MOLE X
5
12
Audio output
3D glasses
34
6
7
8
910 Microphone input
11
12
English
Installation
Connecting a Video source
Due to the
difference in
applications for
each country,
some regions may
have different
accessories.
(*) Optional
accessory
E62405SP
R
5
12
Audio output
3D glasses
34
6
DVD player, Set-top box,
HDTV receiver
1..............................................................................*3 RCA Component cable
2...................................................................................................*HDMI cable
3.......................................................................................... *Audio2 In cable
4................................................................................................Audio In cable
5.....................................................................................................Power cord
6............................................................................................*Audio Out cable
7...................................................................................... Microphone In cable
8....................................................................................................Video cable
9........................................................................................... *3D emitter cable
DVD player, Blu-ray player, Set-top box,
HDTV receiver, Games console
7
8
9
13 English
Installation
Connect to 3D Video Devices
The 3D video
source device
must be
powered on
before the 3D
projector.
If input video
is normal 2D,
please press
“3D Format”
and switch to
“Auto”.
If “SBS Mode”
is active, 2D
video content
will not display
correctly.
Once you have connected your devices together with HDMI
cables, as shown in the diagram, you are ready to begin.
Power ON your 3D video source and your 3D projector.
PlayStation® 3 Games
Make sure that you have updated your console to the latest soft- y
ware version.
Go to the “Settings menu -> Display settings -> Video output -> y
HDMI”. Select “Automatic” and follow the on-screen instructions.
Insert your 3D game disc. Alternatively you can download games y
(and 3D updates) via the PlayStation® network.
Launch the game. In the in-game menu, select “Play in 3D”. y
Blu-ray 3D™ Player
Make sure that your player can support 3D Blu-ray™ disc and that y
3D output is enabled.
Insert the 3D Blu-ray™ disc into the player, press “Play”. y
3D TV (e.g. SKY 3D, DirecTV)
Contact your TV service provider to enable any 3D channels on y
your channel package.
Once enabled, switch to the 3D channel. y
You should see two images side-by-side. y
Switch to the “SBS Mode” of the 3D projector. The option is lo- y
cated in the “Display” section of the projector OSD menu.
3D Device (e.g. 3D DV/DC) with 2D 1080i side by side signal
output
Connect your 3D device and switch to out 3D content with 2D y
side-by-side output to 3D Projector.
You should see two images side-by-side. -
Switch to the “SBS Mode” of the 3D projector. The option is lo- y
cated in the “Display” section of the projector OSD menu.
If watching 3D content from an HDMI 1.4a source (e.g. 3D Blu-ray)
your 3D glasses should always be in sync. If watching 3D content
from an HDMI 1.3 source (e.g. 3D broadcast using SBS mode) it may
be necessary to use the projector’s 3D Sync-Invert option to optimize
your 3D experience. The option is located in the “Display ->3D” sec-
tion of the projector OSD menu.
14
English
Installation
3D Broadcast 3D Blu-ray™ Disc 3D Console Games
SKY+HD, cable/satellite
box 3D Blu-ray™ Player
PlayStation® 3
3D DLP®Link™ Glasses
Full 3D 1080p DLP® Projector
3D RF Glasses 3D Emitter
15 English
Installation
To turn ON 3D glasses.1.
Verify that 3D content is being sent to the projector and 2.
signal is compatible with projector specications.
Turn on the “3D Mode” (Off/DLP-Link/VESA 3D - depend-3.
ing on which type of glasses you are using) of the 3D
projector. The option is located in the “Display” section of
the projector OSD menu.
Turn on 3D glasses and verify image appears in 3D with-4.
out eyestrain.
If the image does not appear in 3D, please check 3D 5.
device set up correctly to send out 3D image or not. Or
“SBS Mode” should turn on when input signal is 2D 1080i
side-by-side and repeat previous steps 1 ~ 4.
It may be necessary to use projector’s “3D Sync-Invert” 6.
option to optimize your 3D experience. The option is
located in the “Display” section of the projector OSD menu.
To turn OFF 3D glasses: Press the “Power” button and 7.
hold until the LED switches off.
For more detailed information, please refer to the 3D 8.
glasses user’s guide, or manufacturer's Website.
Using the 3D glasses
For more de-
tailed informa-
tion, please
refer to 3D
glasses user’s
guide.
16
English
Installation
Powering On/Off the Projector
Turn on the projec-
tor rst and then
select the signal
sources.
(*) Optional
accessory.
Powering On the Projector
1. Securely connect the power cord and signal cable. When
connected, the On/Standby LED will turn Red.
2. Turn on the lamp by pressing “ ” button either on the top of
the projector or on the remote. The On/Standby LED will now
turn Blue.
The startup screen will display in approximately 10 seconds.
The rst time you use the projector, you will be asked to
select the preferred language and power saving mode.
3. Turn on and connect the source that you want to display
on the screen (computer, notebook, video player, etc). The
projector will detect the source automatically. If not, push
menu button and go to “OPTIONS”.
Make sure that the “Source Lock” has been set to “Off”.
If you connect multiple sources at the same time, press the
“SOURCE” button on the Remote Control or direct source
keys on the remote control to switch between inputs.
Freeze
Power Switch
L R
or
17 English
Installation
Powering Off the Projector
1. Press the “ ” button on the remote control or on the
Control Panel to turn off the projector. The following
message will be displayed on the screen.
Power Off?
Press Power again
Press the “ ” button again to conrm otherwise the
message will disappear after 15 seconds. When you press
the “ ” button for the second time, the projector will display
countdown timer and will shut down.
2. The cooling fans continue to operate for about 10 seconds
for cooling cycle and the On/Standby LED will ash Blue.
When the LED lights solid Red, the projector On/Standby
has entered standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply
press “ ” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and
the projector.
4. Do not turn on the projector immediately following a power
off procedure.
Power Off?
Press Power again
18
English
Installation
Contact the
nearest service
center if the
projector displays
these symptoms.
See pages 105-
106 for more
information.
Warning Indicator
When the warning indicators (see below) come on,
the projector will automatically shutdown:
“LAMP” LED indicator is lit red and if “On/Standby” indicator
ashes red.
“TEMP” LED indicator is lit red and if “On/Standby” indicator
ashes red. This indicates the projector has overheated.
Under normal conditions, the projector can be switched
back on.
“TEMP” LED indicator ashes red and if “On/Standby”
indicator ashes red.
Unplug the power cord from the projector, wait for 30 seconds
and try again. If the warning indicator light up again, please
contact your nearest service center for assistance.
19 English
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting
the image height.
1. Locate the adjustable foot you wish to modify on the
underside of the projector.
2. Rotate the adjustable ring clockwise to raise the projector
or counter clockwise to lower it. Repeat with the remaining
feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
20
English
Installation
Adjusting the Projector’s Focus
To focus the image, slide the focus switch until the image is
clear.
Standard throw series (XGA): The projector will focus at dis-
tances from 1.55 to 2.21 feet (0.47 to 0.68 meters) counted
from the center of lens..
Standard throw series (WXGA): The projector will focus
at distances from 1.59 to 2.15 feet (0.49 to 0.66 meters)
counted from the center of lens..
Standard throw series (1080p): The projector will focus
at distance from 1.46 to 1.83 feet (0.45 to 0.56 meters)
counted from the center of lens.
Adjusting Projection Image Size
Projection Image Size (XGA) from 70”-100” (1.78 to 2.54
meters).
Projection Image Size (WXGA) from 85”-115” (2.16 to 2.92
meters).
Projection Image Size (1080p) from 80”-100” (2.03 to 2.54
meters).
Focus Switch
21 English
Installation
a
b
p
c
m
g
d
(H)
(W)
p
a
b
c
m
g
d
(H)
(W)
Variables:
“ ”: Image Offset (m) from the center of the lens to the top of the vertical image.a
“ ”: Distance from the center of the lens to the bottom of the projector.b
“ ”: Distance between the wall (projection surface) to the back of the projector.c
“ ”: Image Diagonal.d
“ ”: Distance between the center of the lens and wall (projection surface).g
“ ”: Distance between the wall (projection surface) and the front of the projector.m
“ ”: Distance from top of projector to the mounting hole.p
“ ”: Height of the Image.H
“ :Width of the image.W”
22
English
Installation
a b c d W H g Pm
Image Offset
from the center
of the lens to the
top of the vertical
image (m)
Distance from center
of lens to the bottom
of projector (m)
Distance between
the wall (projection
surface) to the back
of projector (m)
Image Diagonal
(inch)
Width of Image
Size
Height of Im-
age Size
Distance
between
the center
of lens and
wall(projection
surface)
Distance between
the wall(projection
surface) and the
front of the projec-
tor (m)
Distance from top
of projector to
mounting hole (m)
(inch) (m) (inch) (m) (feet) (m)
0.181 0.0631 0.219 70 56.0 1.42 42.0 1.07 1.55 0.47 0.253 0.115
0.192 0.0631 0.246 74 59.2 1.50 44.4 1.13 1.64 0.50 0.253 0.115
0.207 0.0631 0.287 80 64.0 1.63 48.0 1.22 1.77 0.54 0.253 0.115
0.233 0.0631 0.354 90 72.0 1.83 54.0 1.37 1.99 0.61 0.253 0.115
0.259 0.0631 0.422 100 80.0 2.03 60.0 1.52 2.21 0.68 0.253 0.115
a b c d W H g Pm
Image Offset
from the center
of the lens to the
top of the vertical
image (m)
Distance from center
of lens to the bottom
of projector (m)
Distance between
the wall (projection
surface) to the back
of projector (m)
Image Diagonal
(inch)
Width of Image
Size
Height of Im-
age Size
Distance
between
the center
of lens and
wall(projection
surface)
Distance between
the wall(projection
surface) and the
front of the projec-
tor (m)
Distance from top
of projector to
mounting hole (m)
(inch) (m) (inch) (m) (feet) (m)
0.172 0.0631 0.232 85 72.1 1.83 45.0 1.14 1.59 0.49 0.253 0.115
0.176 0.0631 0.245 87 74.0 1.88 46.2 1.17 1.63 0.50 0.253 0.115
0.182 0.0631 0.261 90 76.4 1.94 47.7 1.21 1.69 0.51 0.253 0.115
0.202 0.0631 0.318 100 84.8 2.15 53.0 1.35 1.87 0.57 0.253 0.115
0.222 0.0631 0.375 110 93.3 2.37 58.3 1.48 2.06 0.63 0.253 0.115
0.232 0.0631 0.403 115 97.5 2.48 60.9 1.55 2.15 0.66 0.253 0.115
a b c d W H g Pm
Image Offset
from the center
of the lens to the
top of the vertical
image (m)
Distance from center
of lens to the bottom
of projector (m)
Distance between
the wall (projection
surface) to the back
of projector (m)
Image Diagonal
(inch)
Width of Image
Size
Height of Im-
age Size
Distance
between
the center
of lens and
wall(projection
surface)
Distance between
the wall(projection
surface) and the
front of the projec-
tor (m)
Distance from top
of projector to
mounting hole (m)
(inch) (m) (inch) (m) (feet) (m)
0.179 0.0631 0.193 80 69.7 1.77 39.2 1.00 1.46 0.45 0.253 0.115
0.200 0.0631 0.244 89 77.6 1.97 43.7 1.11 1.63 0.50 0.253 0.115
0.202 0.0631 0.249 90 78.4 1.99 44.1 1.12 1.65 0.50 0.253 0.115
0.224 0.0631 0.305 100 87.2 2.21 49.0 1.25 1.83 0.56 0.253 0.115
Standard throw XGA (4:3)
These tables are for user’s reference only.
Standard throw WXGA (16:10)
Standard throw 1080p (16:9)
23 English
User Controls
Control Panel
Control Panel & Remote Control
Using the Control Panel
POWER Refer to the “Power On/Off the Projector” section on
pages 16-17.
SOURCE Press to select an input signal.
Lamp LED Indicate the projector’s lamp status.
Temp LED Indicate the projector’s temperature status.
IR Receiever Receives infrared signals from the remote
control.
24
English
User Controls
Remote Control
Using the Remote Control
Power Press to turn on / off the projector.
Switch Press to switch the USB mouse on / off.
Display
blank /
audio mute
Press to hide / unhide the screen picture
and turn off / on audio.
Freeze Press to freeze the projector image.
Mute Press to momentarily turn off / on the audio.
Mouse left
click LUse as mouse left click.
Mouse right
click RUse as mouse right click.
Four
directional
select keys
Use to select items or make
adjustments to your selection.
Enter Con rm your item selection.
Page - Press to page down.
Laser Use as laser pointer.
Page + Press to page up.
Keystone
-
+
Press to adjust image distortion caused by
tilting the projector.
Volume
-
+
Press to adjust to increase / decrease the
volume.
Aspect ratio
/ 1
Press to change aspect ratio of a dis- `
played image.
Use as numeric keypad number “1”. `
Menu / 2
Press to display or exit the on-screen `
display menus for projector.
Use as numeric keypad number “2”. `
Freeze
Power Switch
L R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User 1
8
User 2
9
User 3
Source
0
Resync
Page+Laser
Enter
25 English
User Controls
3D / 3
Press to manually select a 3D mode that `
matches your 3D content.
Use as numeric keypad number “3”. `
HDMI / 4 Press to choose HDMI source. `
Use as numeric keypad number “4”. `
VGA / 5 Press to choose VGA source. `
Use as numeric keypad number “5”. `
Video / 6 Press to choose composite video source. `
Use as numeric keypad number “6”. `
User1 / 7; User2 / 8;
User3 / 9
User dened keys. `
Use as numeric keypad numbers “7”, “8”, `
and “9” accordingly.
Source Press to select an input signal.
Brightness
mode / 0
Press to automatically adjust the picture `
brightness to give an optimum contrast
performance.
Use as numeric keypad number “0”. `
Re-sync Press to automatically synchronize the
projector to the input source.
Freeze
Power Switch
L R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HD MI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+Laser
Enter
Using the Remote Control
26
English
User Controls
Installing Batteries
Two size AAA batteries are supplied for Remote Control.
Replace only with the same or equivalent type recommended by the
manufacturer.
CAUTION
Improper use of batteries can result in chemical leakage or explo-
sion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries
have different characteristics.
Do not mix old and new batteries. Mixing old and new batteries can
shorten the life of new batteries or cause chemical leakage in old
batteries.
Remove batteries as soon as they are worn out. Chemicals that leak
from batteries that come in contact with skin can cause a rash. If you
nd any chemical leakage, wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life ex-
pectancy due to storage conditions.
If you will not be using the remote control unit for an extended period
of time, remove batteries from it.
When you dispose of the battery, you must obey the law in the rela-
tive area or country.
27 English
User Controls
Sub Menu Settings
Main Menu
The Projector has multilingual On-screen Display menus that
allow you to make image adjustments and change a variety of
settings. The projector will automatically detect the source.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Control Panel.
2 When OSD is displayed, use keys to select any item in the
main menu. While making a selection on a particular page, press
or “Enter” key to enter sub menu.
3. Use keys to select the desired item in the sub menu and
then press or “Enter” key to view further settings. Adjust the
settings by key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press “Enter” or “Menu” to conrm, and the screen will return to
the main menu.
6. To exit, press “Menu” again. The OSD menu will close and the
projector will automatically save the new settings.
On-screen Display Menus
DIsplay Mode
Brightness
Contrast
IMAGE
Sharpness
Color
Tint
Advanced
Presentation
28
English
User Controls
Menu Tree
Main
Menu Sub Menu Advanced Menu Parameter Single Item in the Menu Value or
Default Notes
IMAGE
Display Mode
Presentation / Bright /
Movie / sRGB / Blackboard
/ DICOM SIM. / 3D / User
Each mode can
adjust and save to
user mode.
Brightness -50~ +50
Contrast -50~ +50
Sharpness 1~ 15
Color -50~ +50
Tint -50~ +50
Advanced
Noise Reduction 0~10
BrilliantColor™ 1~10
Gamma
Film/
Graphic/1.8/2.0/2.2/2.6/
Blackboard / DICOM
SIM./3D
All gamma could
be selected for all
display modes.
Color Temp. Standard/Cool / Cold
Color Space
Not HDMI Input: Auto /
RGB / YUV Auto
HDMI Input: Auto/
RGB(0~255) /
RGB(16~235)/ YUV
Auto
RGB Gain/Bias
Red Gain
Green Gain
Blue Gain
Red Bias
Green Bias
Blue Bias
Reset
To reset current
source with current
display mode for
RGB Gain/Bias
Exit
Color Matching
Red Hue/ Saturation /Gain/
Exit -50~ +50
Green Hue/ Saturation /Gain/
Exit -50~ +50
Blue Hue/ Saturation /Gain/
Exit -50~ +50
29 English
User Controls
Main
Menu Sub Menu Advanced Menu Parameter Single Item in the Menu Value or
Default Notes
IMAGE
Advanced
Color Matching
Cyan Hue/ Saturation /Gain/
Exit -50~ +50
Magenta Hue/ Saturation /Gain/
Exit -50~ +50
Yellow Hue/ Saturation /Gain/
Exit -50~ +50
White R/G/B/Exit -50~ +50
Reset To reset current
source with current
display mode for
CMS settings
Exit
Exit
Reset Yes/No
To reset current
source with current
display mode for
image settings.
DISPLAY
Format
4:3
Auto
16:9/16:10[WXGA]
LBX
Native
Auto
Default
is
“Auto”
Zoom -5 ~ +25
Edge Mask 0 ~ 10
Image Shift
H -50~ +50 Up/Down/Right/
Left(Icon in center)
V -50~ +50
V Keystone -15~ +15 1080p: -5~+5
IMAGE 3D
3D Mode
DLP-Link/ VESA 3D /Off
(For projector don’t have
VESA port, use “ IR “)
DLP-
Link
3D->2D 3D/ L/ R
The items would be
greyed out when 3D
mode sets to Off.
3D Format Auto/SBS/Top and
Bottom/Frame Sequntail
3D Sync Invert On/Off Off
Exit
30
English
User Controls
Main
Menu Sub Menu Advanced Menu Parameter Single Item in the Menu Value or
Default Notes
SETUP
Language
English / Deutsch / Français /
Italiano / Español / Português /
Polski / Nederlands / Svenska /
Norsk/Dansk / Suomi / Ελληνικά/
ᖅᡝϛМ /
࿒፩ၭ / 日本語 /
㘆ท♞ / Русский / Magyar /
Čeština / / Türkçe / /
Română/Slovenčina
English
Projection
Front-Desktop
Front
Ceiling
Rear-Desktop
Front-Ceiling
Rear-Ceiling
Screen Type 16:10/16:9 (WXGA
MODEL)
Default
is
“16:10”
Menu Loca-
tion
Top Left
Center
Top Right
Center
Bottom Left
Bottom Right
31 English
User Controls
Main
Menu Sub Menu Advanced Menu Parameter Single Item in the Menu Value or
Default Notes
SETUP
Security
Security Setting On/Off Off
Security Timer
Month 0~12
Password is required
if “Security” is
selected.
Day 0~30
Hour 0~24
Exit
Change Password
Exit
Signal (RGB)
Frequency -5~+5
Depends on signal
Phase 0~63
H. Position -5~+5
V. Position -5~+5
Automatic Enable/
Disable
Exit
Signal (Video)
White Level -50~+50
Black Level -50~+50
Exit
Projector ID 00~99
Auto Settings
Internal Speaker On/Off On
Audio 1 (RCA) for
Composite
Audio 2 (Mini jack)
for VGA
Mute On/Off Off
Volume
Audio 0-10
MIC 0-10
Audio Input Default/Audio 1/Audio 2 Default
Exit
Advanced
Logo Optoma/ Neutral /User Optoma
Logo Capture
Closed Captioning CC1/CC2/Off Off
Exit
32
English
User Controls
Main
Menu Sub Menu Advanced Menu Parameter Single Item in the Menu Value or
Default Notes
SETUP Network
LAN Settings
Network
Status Read-Only
Never time-out on
this page.
DHCP On/Off
IP Address
Subnet
Mask
Gateway
DNS
Apply Yes/No
MAC
Address Read-Only
Exit
Control Settings
Crestron On/Off On
Extron On/Off On
PJ Link On/Off On
AMX
Device
Discovery
On/Off On
Telnet On/Off On
Exit
OPTIONS
Input Source
HDMI 1/HDMI 2/VGA 1/
VGA 2/Video
When no signal
input, user still
could do selection
for “Input Source”
from OSD.
Exit
Source Lock On/Off Off
High Altitude On/Off Off
Information
Hide On/Off Off
Keypad Lock On/Off Off
Test Pattern
None / Grid(white)
/ Grid(Green) /
Grid(Magenta)/ White
None
Background
Color
Blue / Black / Red / Green
/ White Blue Default is Blue
12V Trigger On/Off On
VGA2 Switch In/Out Out
33 English
User Controls
Main
Menu Sub Menu Advanced Menu Parameter Single Item in the Menu Value or
Default Notes
OPTIONS
Advanced
Direct Power On On/Off
Signal Power on On/Off
Auto Power Off
(min) 0~180
Sleep Timer (min) 0~990
Power Mode
( Standby) Active/ Eco. Eco.
Quick Resume On/Off Off
Remote Settings
User 1
HDMI2/VGA2/Test
Pattern/LAN/Brightness/
Contrast/Sleep Timer/
Color Matching/Color
Temp/Gamma/ Source
Lock /Projection/Lamp
Settings/Zoom/Freeze
HDMI2
User 2
HDMI2/VGA2/Test
Pattern/LAN/Brightness/
Contrast/Sleep Timer/
Color Matching/Color
Temp/Gamma/ Source
Lock /Projection/Lamp
Settings/Zoom/Freeze
VGA2
User 3
HDMI2/VGA2/Test
Pattern/LAN/Brightness/
Contrast/Sleep Timer/
Color Matching/Color
Temp/Gamma/ Source
Lock /Projection/Lamp
Settings/Zoom/Freeze
Test
Pattern
Exit
Lamp Settings
Lamp Hour Read-Only[Range 0~ 9999]
Lamp Reset Yes/No No
Lamp Reminder On/Off On
Brightness Mode Bright/Eco./Dynamic/
Eco+ Bright
Exit
Filter Settings
Filter Usage Hours Read-Only [Range 0~ 9999]
Filter Reminder Off/
300hr/500hr/800hr/1000hr 500hr
Filter Reset Yes/No No
Exit
34
English
User Controls
Main
Menu Sub Menu Advanced Menu Parameter Single Item in the Menu Value or
Default Notes
OPTIONS Reset Current/All
The denition of
Current: To reset all
OSD settings to be
default for current
source and current
timing.
The denition of
All: To reset all OSD
settings to be default
for all source and all
timing..
35 English
User Controls
IMAGE
Display Mode
There are many factory presets optimized for various types of
images.
Presentation: This mode is suitable for showing in front of public `
in connection to the PC.
Bright: Maximum brightness from PC input. `
Movie: This mode is suitable for watching video. `
User: Memorize user’s settings. `
Blackboard: This mode should be selected to achieve optimum `
color settings when projecting onto a blackboard (green).
DICOM SIM.: This mode can project a monochrome medical `
image such as an X ray radiography, MRI, etc.
sRGB: Standardized accurate color. `
3D: To experience the 3D effect, you need to have 3D glasses, `
make sure your PC/portable device has a 120 Hz signal output
quad buffered graphics card and have a 3D Player installed.
IMAGE
DIsplay Mode Presentation
Brightness
Contrast
Sharpness
Color
Tint
Advanced
36
English
User Controls
Presentation
Bright
Movie
Blackboard
DICOM SIM.
sRGB
User
User
Brightness
Adjust the brightness of the image.
Press the ` to darken image.
Press the► ` to lighten the image.
Brightness
Contrast
The contrast controls the degree of difference between the light-
est and darkest parts of the picture.
Press the ` to decrease the contrast.
Press the ` to increase the contrast.
Contrast
37 English
User Controls
Sharpness
Adjust the sharpness of the image.
Press the ` to decrease the sharpness.
Press the ` to increase the sharpness.
Sharpness
Color
Adjust a video image from black and white to fully saturated color.
Press the ` to decrease the amount of saturation in the im-
age.
Press the ` to increase the amount of saturation in the im-
age.
Color
Tint
Adjust the color balance of red and green.
Press the ` to increase the amount of green in the image.
Press the ` to increase the amount of red in the image.
Tint
Reset
Choose “Yes” to return the factory default settings for “IMAGE”.
Exit
Choose “Exit” to exit the menu.
38
English
User Controls
IMAGE | Advanced
Noise Reduction
Selects a lter sensitivity to noise. A higher value may improve
noisy sources, but it will soften the image.
Press the ` to decrease the noise in the image.
Press the ` to increase the noise in the image.
Noise Reduction
Gamma
This allows you to set up gamma curve type. After the initial setup
and ne tuning is completed, utilize the Gamma Adjustment steps
to optimize your image output.
Film: for home theater. `
Graphics: for PC / Photo source. `
Blackboard: This mode should be selected to achieve optimum `
color settings when projecting onto a blackboard (green).
DICOM SIM.: This mode can project a monochrome medical `
image such as an X ray radiography, MRI, etc.
Press the or to select the mode.
Gamma
Film
IMAGE
Advanced
Noise Reduction
Gamma Film
Brilliant Color
RGB Gain/Bias
Cool
Color Matching
Color Space
Exit
Auto
Color Temp.
39 English
User Controls
BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and
enhancements to enable higher brightness while providing true,
more vibrant colors in picture.
Press the ` to stronger enhance the image.
Press the ` to less enhance the image.
Brilliant Color
RGB Gain/Bias
This settings allows to congure the brightness (gain) and contrast
(bias) of an image.
Press the ` to decrease a chosen color gain and bias.
Press the ` to increase a chosen color gain and bias.
RGB Gain/Bias
Red Gain
Green Gain
Blue Gain
Red Bias
Green Bias
Blue Bias
Reset Exit
Color Temp.
Press the or to select a color temperature from Standard,
Cool and Cold.
Cool
Color Temp.
40
English
User Controls
Color Matching
Press the or or or into the next menu and then use
to select the item.
Color Matching
Red
Green
Blue
White Reset
Exit
Yellow
Magenta
Cyan
Red `: Press the Hue, Saturation and Gain or to select
Colors. Then press the or to decrease or increase the
value respectively.
Red
Hue
Saturation
Gain
Exit
Cyan `: Press the Hue, Saturation and Gain or to select
Colors. Then press the or to decrease or increase the
value respectively.
Cyan
Hue
Saturation
Gain
Exit
41 English
User Controls
Green `: Press the Hue, Saturation and Gain or to select
Colors. Then press the or to decrease or increase the
value respectively.
Green
Hue
Saturation
Gain
Exit
Magenta `: Press the Hue, Saturation and or to select
Gain Colors. Then press the or to decrease or increase
the value respectively.
Magenta
Hue
Saturation
Gain
Exit
Blue `: Press the Hue, Saturation and Gain or to select
Colors. Then press the or to decrease or increase the
value respectively.
Blue
Hue
Saturation
Gain
Exit
Yellow `: Press the Hue, Saturation and Gain or to select
Colors. Then press the or to decrease or increase the
value respectively.
Yellow
Hue
Saturation
Gain
Exit
42
English
User Controls
White `: Press the Hue, Saturation and Gain or to select
Colors. Then press the or to decrease or increase the
value respectively.
White
Hue
Saturation
Gain
Exit
Reset: Choose “ ` Reset” to return the factory default settings
for color adjustments.
Color Space
Press the or to select an appropriate color matrix type
from the following:
Non-HDMI Input: Auto, RGB or YUV `
HDMI Input: Auto, RGB(0-255), RGB(16-235) or YUV. `
Color Space
Auto
Reset
Current: Choose “Yes” to return the display parameters on this `
menu to the factory default settings.
All: Choose “Yes” to return the display parameters on all menus `
to the factory default settings.
Exit
Choose “Exit” to exit the menu.
43 English
User Controls
DISPLAY
Format
Press the or to choose your desired aspect ratio between
4:3, 16:9/16:10 (WXGA), LBX, Native, and Auto.
Format
XGA
4:3: This format is for 4:3 input sources. `
16:9: This format is for 16:9 input sources, like HDTV and `DVD
enhanced for Wide screen TV.
Native: This format displays the original image without any `
scaling.
AUTO: Automatically selects the appropriate display format. `
Source 480i/p 576i/p 1080i/p 720p
4:3 Scale to 1024 x 768
16:9 Scale to 1024 x 576
Native No scaling will be made; the resolution is dependent on
which input source and is then displayed.
Auto
If source is 4:3, it will be auto resized to 1024 x 768 `
If source is 16:9, it will be auto resized to 1024 x 576 `
If source is 15:9, it will be auto resized to 1024 x 614 `
If the source is 16:10, it will be auto resized to 1024 x 640 `
DISPLAY
Format
Zoom
Edge Mask
Image Shift
V. Keystone
Exit
44
English
User Controls
WXGA
4:3: `This format is for 4:3 input sources.
16:9: This format is for 16:9 input sources, like HDTV and `DVD
enhanced for Wide screen TV.
16:10: This format is for 16:10 input sources, like widescreen `
laptops.
LBX: This format is for non-16x9, letterbox source and for us- `
ers who use external 16x9 lens to display 2.35:1 aspect ratio
using full resolution.
Native: This format displays the original image without any `
scaling.
AUTO: Automatically selects the appropriate display format. `
Detail informations about LBX mode:
Some Letter-Box Format DVDs are not enhanced for 16x9 TVs. 1.
In this situation, the image will not look right when displayed in
16:9 mode. In this situation, please try to using the 4:3 mode to
view the DVD. If the content is not 4:3, there will be black bars
around the image in 16:9 display. For this type of content, you
can use LBX mode to ll the image on the 16:9 display.
If you use an external anamorphic lens, this LBX mode also 2.
allows you to watch a 2.35:1 content (include Anamorphic
DVD and HDTV lm source) that support anamorphic wide is
enhanced for 16x9 Display in a wide 2.35:1 image. In this case,
there are no black bars. Lamp power and vertical resolution
are fully utilized.
16:9 Screen 480i/p 576i/p 1080i/p 720p PC
4:3 Scale to 960 x 720
16:9 Scale to 1280 x 720
LBX Scale to 1280 x 960, in order to get the central 1280 x 720
image displayed on the screen.
Native 1:1 mapping
centered
1:1 map-
ping display
1280 x 720
1280 x 720
centered
1:1 mapping
centered
Auto
If this format is selected, the screen type will automati- `
cally set to 16:9 (1280 x 720)
If source is 4:3, it will be auto resized to 960 x 720 `
If source is 16:9, it will be auto resized to 1280 x 720 `
If source is 15:9, it will be auto resized to 1200 x 720 `
If the source is 16:10, it will be auto resized to 1152 x 720 `
45 English
User Controls
16:10 Screen 480i/p 576i/p 1080i/p 720p PC
4:3 Scale to 1066 x 800
16:10 Scale to 1280 x 800
LBX Scale to 1280 x 960, in order to get the central 1280 x 800
image displayed on the screen.
Native 1:1 mapping
centered
1:1 map-
ping display
1280 x 800
1280 x 720
centered
1:1 mapping
centered
Auto
Input source will be t into 1280x800 display area and be `
kept its original aspect ratio
If source is 4:3, auto resize to 1066 x 800 `
If source is 16:9 auto resize to 1280 x 720 `
If source is 15:9 auto resize to 1280 x 768 `
If source is 16:10 auto resize to 1280 x 800 `
1080P
4:3: `This format is for 4:3 input sources.
16:10: This format is for 16:10 input sources, like widescreen `
laptops.
LBX: This format is for non-16x9, letterbox source and for us- `
ers who use external 16x9 lens to display 2.35:1 aspect ratio
using full resolution.
Native: This format displays the original image without any `
scaling.
AUTO: Automatically selects the appropriate display format. `
16:9 Screen 480i/p 576i/p 1080i/p 720p PC
4:3 Scale to 1440 x1080
16:10 Scale to 1920x1080
LBX Scale to 1920 x 1440, in order to get the central
1920 x 1080 image displayed on the screen.
Native
1:1 mapping centered
No scaling will be made; the resolution is dependent on
which input source and is then displayed.
Auto
If this format is selected, the screen type will automatically `
become 16:9
If source is 4:3, auto resize to 1440 x 1080 `
If source is 16:9 auto resize to 1920 x 1080 `
If source is 16:10 auto resize to 1920 x 1200 and cut to `
1920 x x1080 area display
46
English
User Controls
Zoom
Press the ` to reduce the size of an image.
Press the ` to magnify an image on the projection screen.
Zoom
Edge Mask
Edge mask the image to remove video encoding noise on the
edge of video source.
Press the ` to decrease the edge mask in image.
Press the ` to increase the edge mask in image.
Edge Mask
Image Shift
Press the into the next menu as below and then press the
or or or to select item.
Image Shift Image Shift
Image Shift Image Shift
H: Press the ` to shift the projected image position
horizontally.
V: Press the ` to shift the projected image position verti-
cally.
Each I/O has
different setting of
“Edge Mask”.
“Edge Mask” and
“Zoom” can’t work
at same time.
47 English
User Controls
V Keystone
Press the or to adjust image distortion vertically and make
a squarer image.
V. Keystone
Exit
Choose “Exit” to exit the menu.
48
English
User Controls
3D Format is only
supported on 3D
Timing on page
94.
“3D Format” is
only supported on
non-HDMI 1.4a 3D
timing.
DISPLAY | 3D
3D Mode
Off: `Select “Off” to turn off 3D mode.
Press the ` or to select the 3D mode.
3D Mode
DLP - Link
DLP-Link: Select “DLP-Link” to use optimized settings for DLP `
Link 3D Glasses. (refer to page 15).
VESA 3D: Select “VESA 3D” to use optimized setting for VESA `
3D Glasses. (refer to page 15).
3D -> 2D
Press the ` or to select 3D -> 2D.
3D: Display 3D signal. `
L (Left): Display the left frame of 3D content. `
R (Right): Display the right frame of 3D content. `
DISPLAY
3D Mode
3D Format
3D Sync. Invert
Exit
3D
DLP - Link
Frame Sequential
Off
49 English
User Controls
3D Format
Press the ` or to select 3D format.
3D Format
Frame Sequential
Auto: When a 3D identication signal is detected, the 3D for- `
mat is selected automatically.
SBS: Display 3D signal in “Side-by-Side” format. `
Top and Bottom: Display 3D signal in “Top and Bottom” format. `
Frame Sequential: Display 3D signal in “Frame Sequential” `
format.
3D Sync. Invert
Press the ` or to select 3D sync. invert.
3D Sync. Invert
Off On
Press the “On” to invert left and right frame contents. `
Press the “Off” for default frame contents. `
Exit
Choose “Exit” to exit the menu.
50
English
User Controls
SETUP
Exit
English
SETUP
Language
Projection
Menu Location
Audio Settings
Sceen Type
Security
Projector ID
Signal (RGB)
Advanced
Network
Signal (Video)
Advanced
Network
Exit
51 English
User Controls
Language
Choose the multilingual OSD menu. Press into the sub menu
and then press the or or or -►key to select your pre
ferred language. Press “Enter” to nalize the selection.
Rear-Desktop and
Rear-Ceiling are
to be used with a
translucent screen.
Projection
Press the or or or -►key to select the preferred pro
jection.
Projection
Exit
` Front-Projection
This is the default selection. The image is projected straight on
the screen.
` Rear-Desktop
When selected, the image will appear reversed.
` Front-Ceiling
When selected, the image will turn upside down.
` Rear-Ceiling
When selected, the image will appear reversed in upside down
position
Language
Exit
52
English
User Controls
Menu Location
Press the or or or key to select the preferred menu
location.
Menu Location
Exit
Screen Type
Press the or to choose the screen type from16:10* or 16:9.
Screen Type
Projector ID
ID denition can be set up by menu (range 0-99), and allow user
control an individual projector by RS232.
Press the ` to decrease the projector ID number.
Press the ` to increase the projector ID number.
Projector ID
Exit
Choose “Exit” to exit the menu.
*This screen type
applies to WXGA
only.
53 English
User Controls
SETUP |
Audio Settings
Internal Speaker
Choose the “On” or “Off” to turn on or off the internal speaker.
Internal Speaker
Off On
Mute
Choose the “On” to turn mute on. `
Choose the “Off” to turn mute off. `
Mute
Off On
Volume
Press the ` to decrease the volume.
Press the ` to increase the volume.
Volume
Audio
Mic
Exit
“Mute” function
affects both
internal and
external speaker
volume.
SETUP
Audio Settings
Internal Speaker
Mute
Volume
Audio Input
Off
Off
Default
Exit
54
English
User Controls
Audio Input
The default audio settings are on the back panel of the projector.
Use this option to reassign any of the Audio Inputs (1 or 2) to the
current image source. Each Audio input can be assigned to more
than one video source.
Press ` or to select audio input.
Audio Input
Default
Default. `
Audio 1: (RCA) for Composite `
Audio 2: (Mini jack) for VGA `
Exit
Choose “Exit” to exit the menu.
56
English
User Controls
Change Password
First time: `
Press “Enter” key to set the password.1.
The password has to be 4 digits. 2.
Use number button on the remote or on-screen numeric key-3.
pad to enter your new password and then press “Enter” key to
conrm your password.
Change Password: `
(If your remote does not have a number keypad, please use
the up/down arrows to change each digit of the password,
then press enter to conrm)
Press “Enter” to input old password.1.
Use number button 2. to enter cur-or on-screen numeric keypad
rent password and then press “Enter” to conrm.
Enter new password (4 digits in length) using the number but-3.
tons on the remote, then press “Enter” to conrm.
Enter new password again and press “Enter” to conrm.4.
If the incorrect password is entered 3 times, the projector will `
automatically shut down.
If you have forgotten your password, please contact your local `
ofce for support.
Exit
Choose “Exit” to exit the menu.
Pass-code default
value is “1234” (rst
time).
REMOTE
Enter Security Code (4 digits)
57 English
User Controls
SETUP | Network
SETUP
Network
LAN Settings
Control Settings
Exit
LAN Settings
Loading network conguration
Please wait...
For more information on LAN Settings, refer to page 58-59, and
62-69
Control Settings
For more information on Control Settings, refer to page 60-69.
58
English
User Controls
SETUP |
Network|LAN
Settings
Network Status
Display the network connection status (read-only).
MAC Address
Display the MAC address (read-only).
DHCP
DHCP
Off On
On: Projector will obtain an IP address automatically from your `
network.
Off: To assign IP, Subnet Mask, Gateway and DNS `
conguration manually.
Exiting OSD will automatically apply the entered values.
IP Address
IP Address
Display the IP address.
SETUP
Network LAN Settings
Network Status
MAC Address
DHCP
IP Address
Subnet Mask
Gateway
DNS
Apply
Connected
Off
Exit
59 English
User Controls
Subnet Mask
Subnet Mask
Display subnet mask number.
Gateway
Gateway
Display the default gateway of the network connected to the
projector.
DNS
DNS
Display DNS number.
Apply
Press and then choose “Yes” to apply the selection.
Apply
No Yes
Exit
Choose “Exit” to exit the menu.
60
English
User Controls
SETUP |
Network|Control
Settings
Crestron
Crestron
Off On
Use this function to select the network function (port: 41794). For
more information, please visit http://www.crestron.com and
www.crestron.com/getroomview.
On: The Crestron function is active. `
Off: The Crestron function is inactive. `
Extron
Extron
Off On
Use this function to select the network function (port: 2023).
On: The Extron function is active. `
Off: The Extron function is inactive. `
PJ Link
PJ Link
Off On
Use this function to select the network function (port: 4352).
On: The PJ Link function is active. `
Off: The PJ Link function is inactive. `
SETUP
Network: Control Settings
Crestron
Extron
PJ Link
AMX Device Discovery
Telnet
Off
Off
Off
Off
Off
Exit
61 English
User Controls
AMX Device Discovery
AMX Device Discovery
Off On
Use this function to select the network function (port: 1023).
On: The AMX Discovery function is active. `
Off: The AMX Discovery function is inactive. `
Telnet
Telnet
Off On
Use this function to select the network function (port: 23).
On: Telnet is enabled. `
Off: Telnet is disabled. `
Exit
Choose “Exit” to exit the menu.
62
English
User Controls
LAN_RJ45 Function
For simplicity and ease of operation, the W320UST projector
provides diverse networking and remote management features.
The LAN/RJ45 function of the projector through a network, such
as remotely manage: Power On/Off, Brightness and Contrast
settings. Also, projector status information, such as: Video-
Source, Sound-Mute, etc.
(Ethernet)
Projector
Wired LAN Terminal Functionalities
This projector can be controlled by using a PC (laptop) or other
external device via LAN/RJ45 port and compatible ith Crestron /
Extron / AMX (Device Discovery) / PJLink.
Crestron is a registered trademark of Crestron Electronics, Inc. `
of the United States.
Extron is a registered trademark of Extron Electronics, Inc. of `
the United States.
AMX is a registered trademark of AMX LLC of the United `
States.
PJLink applied for trademark and logo registration in Japan, `
the United States of America, and other countries by JBMIA.
Wired LAN Terminal Functionalities
W320UST projector is supported by the specied commands
of the Crestron Electronics controller and related software, for
example RoomView®.
http://www.crestron.com/
This projector is compliant to support Extron device(s) for refer-
ence.
http://www.extron.com/
This projector is supported by AMX ( Device Discovery ).
http://www.amx.com/
Use Ethernet Nor-
mal Cable to con-
nect the projector
to LAN..
63 English
User Controls
This projector supports all commands of PJLink Class1 (Version
1.00).
http://pjlink.jbmia.or.jp/english/
For more detailed information about the various types of exter-
nal devices which can be connected to the LAN/RJ45 port and
remote/control the project, as well as the supported commands
for these external devices, please contact the Support-Service
directly.
LAN RJ45
Connect an RJ45 cable to RJ45 ports on the projector and the 1.
PC (laptop).
On the PC (Laptop), select Start > Control Panel > Network 2.
Connections.
64
English
User Controls
Right-click on the Local Area Connection, and select Property.3.
In the Properties window, select the General tab, and select 4.
Internet Protocol (TCP/IP).
Click “Properties”.5.
65 English
User Controls
Type in the IP address and Subnet mask, then press “OK”.6.
Press the “Menu” button on the projector.7.
Use 8. keys to select SETUP > Network > LAN Settings.
After getting into LAN Settings, input the following connection 9.
parameters:
DHCP: Off `
IP Address: 10.10.10.10 `
Subnet Mask: 255.255.255.255 `
Gateway: 0.0.0.0 `
DNS: 0.0.0.0 `
Press “Enter” to conrm settings.10.
Open a web browser, for example Microsoft Internet Explorer.11.
with Adobe Flash Player 9.0 or higher installed.
In the Address bar, input the projector’s IP address: 12.
10.10.10.10.
66
English
User Controls
Press “Enter”.13.
The projector is setup for remote management. The LAN/RJ45
function displays as follows:
Information Page
Main Page
67 English
User Controls
Tool Page
Contact IT Helpdesk
RS232 by Telnet Function
There is alternative RS232 command control way, in projector so
called “RS232 by TELNET” for LAN/RJ45 interface.
68
English
User Controls
Quick Start-Guide for “RS232 by Telnet”
Check and get the IP address on OSD of the projector. `
Make sure that the PC/laptop can access the web-page of the `
projector.
Make sure that "Windows Firewall" setting is set disabled in `
case of "TELNET" function ltering out by PC/laptop.
.
Start > All Programs.> Accessories > Command Prompt.1.
Input the command format as follows:2.
telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)
(ttt.xxx.yyy.zzz: IP-Address of the projector)
If Telnet-Connection ready, and user can have RS232 com-3.
mand input, then “Enter” key pressed, the RS232 command will
be workable.
69 English
User Controls
Specication for “RS232 by TELENT”:
Telnet: TCP.1.
Telnet port: 23 (for more detail, kindly please get contact with 2.
the service agent or team).
Telnet utility: Windows “TELNET.exe” (console mode).3.
Disconnection for RS232-by-Telnet control normally: Close4.
Windows Telnet utility directly after TELNET connection ready.5.
Limitation 1 for Telnet-Control: there is less than 50 bytes for `
successive network payload for Telnet-Control application.
Limitation 2 for Telnet-Control: there is less than 26 bytes for `
one complete RS232 command for Telnet-Control.
Limitation 3 for Telnet-Control: Minimum delay for next `
RS232 command must be more than 200 (ms).
In Windows XP
built-in “TELNET.
exe” utility, “Enter”
key pressed will
have “Carriage-Re-
turn” and “New-Line”
code.
70
English
User Controls
SETUP |
Signal (RGB)
Automatic
SETUP
Signal (RGB)
Automatic Disable
Exit
Automatically selects the signal. If you use this function, the
Phase, frequency items are grayed out, and if Signal is not auto-
matic, the phase, frequency items will appear for user to manually
tune and saved in settings after that for next time projector turns
off and on again
Phase
Phase
Synchronize the signal timing of the display with the graphic card.
If the image appears to be unstable or ickers, use this function to
correct it.
Press the ` to decrease the phase value.
Press the ` to increase the phase value.
“Signal” is only sup-
ported in Analog
VGA (RGB) signal.
If “Signal” is auto-
matic, the phase,
frequency items are
grayed out, and if
“Signal” is not au-
tomatic, the phase,
frequency items
will appear for the
user to manually
tune and are saved
in the settings after
that for the next
time projector is
turned off and on
again.
SETUP
Signal (RGB)
Automatic Disable
Phase
Frequency
V. Position
H. Position
Exit
71 English
User Controls
Frequency
Frequency
Change the display data frequency to match the frequency of
your computer’s graphic card. Use this function only if the image
appears to icker vertically.
Press the ` to decrease the frequency.
Press the ` to increase the frequency.
H. Position (Horizontal Position)
H. Position
Press the ` to move the image left.
Press the ` to move the image right.
V. Position (Vertical Position)
V. Position
Press the ` to move the image down.
Press the ` to move the image up.
Exit
Choose “Exit” to exit the menu.
72
English
User Controls
White Level
White Level
Adjust the overall white level of the projected image by applying a
gain to the input image.
Press the ` to decrease the white level.
Press the ` to increase the white level.
Black Level
Black Level
Adjust the overall black level of the projected image by applying a
offset to the input image.
Press the ` to decrease the black level.
Press the ` to increase the black level.
Exit
Choose “Exit” to exit the menu.
SETUP |
Signal (Video)
SETUP
Signal (Video)
White Level
Black Level
Exit
73 English
User Controls
Logo
Logo
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
Neutral: Logo is not displayed on startup screen. `
Optoma: Optoma logo is displayed on startup screen. `
User: User-dened background is shown on startup screen. `
Logo Capture
Logo Capture
Do you want to capture the image?
Logo Capture
Processing ...
For a successful
logo capture,
ensure that the
on-screen image
does not exceed
the projector
native resolution.
(1280 x 800).
SETUP |
Advanced
SETUP
Advanced
Logo
Logo Capture
Closed Captioning
Off On
No Yes
74
English
User Controls
Choose “On and “Yes -” ” to capture an image of the picture cur
rently displayed on screen.
Closed Captioning
Closed Captioning
Off
Closed Captioning is a text version of the program sound or other
information displayed on the screen. If the input signal contains
closed captions, you can turn on the feature and watch the chan-
nels. Press or to select between CCI, or CC2. Choose Off
to disable this function.
Exit
Choose “Exit” to exit the menu.
75 English
User Controls
Input Source
Use this option to enable/disable input sources. Press to enter ►
the sub menu and select which sources you require. Press “Enter”
to finalize the selection. The projector will only search for inputs
that are enabled.
Input Source
Video Exit
Source Lock
On: `The projector will only search current input connection.
Off: The projector will search for other signals if the current `
input signal is lost.
Source Lock
Off On
High Altitude
When “On” is selected, the fans will spin faster. This feature is use-
ful in high altitude areas where the air is thin.
On
High Altitude
Off
OPTIONS
OPTIONS
Input Source
Source Lock
High Altitude
Information Hide
Keypad Lock
Test Pattern
Off
12V Trigger
Off
Off
Off
None
On
“VGA2” depends
on the settings of
“VGA2 Switch”.
76
English
User Controls
Information Hide
On: Choose “On” to hide the info message. `
Off: Choose “Off” to show the “searching” message. `
Information Hide
Off On
Keypad Lock
When the keypad lock function is “On”, the Keypad will be locked however, the projector
can be operated by the remote control. By selecting “Off”, you will be able to unlock the
Keypad.
Keypad Lock
Off On
Test Pattern
Display a test pattern. There are Grid, White Pattern and None.
Test Pattern
None
12V Trigger
Off: Choose “Off” to disable the trigger. `
On: Choose “On” to enable the trigger. `
12V Trigger
On
77 English
User Controls
Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or
“White”, screen when no signal is available.
Background Color
White
VGA2 Switch
When the “VGA2 Switch” feature is “In” then VGA2 port functions
as input port. If the “VGA2 Switch” is “Out” then the port functions
as output port for VGA1.
VGA2 Switch
Out In
OPTIONS
OPTIONS
Background Color
VGA2 Switch
Lamp Settings
Advanced
Filter Settings
Reset
Black
Out
Exit
Specyfikacje produktu
| Marka: | Optoma |
| Kategoria: | Projektor |
| Model: | GT5500 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Optoma GT5500, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Projektor Optoma
29 Stycznia 2025
31 Grudnia 2025
31 Grudnia 2025
31 Grudnia 2025
11 Października 2024
9 Października 2024
9 Października 2024
8 Października 2024
5 Października 2024
3 Października 2024
Instrukcje Projektor
- Projektor Sony
- Projektor Yamaha
- Projektor Samsung
- Projektor Leica
- Projektor LG
- Projektor Xiaomi
- Projektor Sharp
- Projektor Lenovo
- Projektor Philips
- Projektor Livoo
- Projektor Acer
- Projektor Epson
- Projektor Hisense
- Projektor Panasonic
- Projektor Promethean
- Projektor Canon
- Projektor Viewsonic
- Projektor Asus
- Projektor Medion
- Projektor OK
- Projektor Lenco
- Projektor Toshiba
- Projektor D-Link
- Projektor Blaupunkt
- Projektor Salora
- Projektor Casio
- Projektor HP
- Projektor Prixton
- Projektor Strong
- Projektor Steinel
- Projektor Kodak
- Projektor Smart
- Projektor ZTE
- Projektor JVC
- Projektor Dell
- Projektor Auna
- Projektor Dahua Technology
- Projektor Eurolite
- Projektor Ricoh
- Projektor Krüger&Matz
- Projektor Renkforce
- Projektor Klarstein
- Projektor Pyle
- Projektor Marantz
- Projektor Showtec
- Projektor Mitsubishi
- Projektor ION
- Projektor XGIMI
- Projektor NEC
- Projektor Polaroid
- Projektor Sanyo
- Projektor Vogel's
- Projektor Hama
- Projektor Cameo
- Projektor Barco
- Projektor 3M
- Projektor Nebula
- Projektor Anker
- Projektor Hitachi
- Projektor Futurelight
- Projektor RCA
- Projektor BenQ
- Projektor Technaxx
- Projektor GPX
- Projektor Overmax
- Projektor Odys
- Projektor EasyMaxx
- Projektor Smartwares
- Projektor Adj
- Projektor Miroir
- Projektor Stairville
- Projektor Elmo
- Projektor Planar
- Projektor Acco
- Projektor Aiptek
- Projektor ASK Proxima
- Projektor Reflecta
- Projektor Yaber
- Projektor Da-Lite
- Projektor Steren
- Projektor Eiki
- Projektor Derksen
- Projektor InFocus
- Projektor Bauer
- Projektor Naxa
- Projektor Vivitek
- Projektor Emtec
- Projektor Celly
- Projektor Vankyo
- Projektor Laserworld
- Projektor Ibm
- Projektor Maxell
- Projektor La Vague
- Projektor Kogan
- Projektor Tzumi
- Projektor EKO
- Projektor MicroVision
- Projektor Elite Screens
- Projektor Celexon
- Projektor Christie
- Projektor Fun Generation
- Projektor Beghelli
- Projektor Magnavox
- Projektor PLUS
- Projektor Varytec
- Projektor AOpen
- Projektor Ultimea
- Projektor Dracast
- Projektor Dukane
- Projektor Dream Vision
- Projektor Knoll
- Projektor DTS
- Projektor Touchjet
- Projektor Boxlight
- Projektor AAXA Technologies
- Projektor Mimio
- Projektor AWOL Vision
- Projektor Smart Tech
- Projektor Atlantis Land
- Projektor KickAss
- Projektor Microtek
- Projektor VAVA
- Projektor Panamorph
- Projektor Mirabella Genio
Najnowsze instrukcje dla Projektor
2 Kwietnia 2025
5 Marca 2025
5 Marca 2025
3 Marca 2025
1 Marca 2025
26 Lutego 2025
20 Lutego 2025
20 Lutego 2025
20 Lutego 2025
18 Lutego 2025