Instrukcja obsługi Onkyo SKF-4800

Onkyo głośnik SKF-4800

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Onkyo SKF-4800 (4 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Speaker System

SKF-4800

Instruction Manual

Thank you for your purchase of the Onkyo speaker

system.

Please read this manual thoroughly before using it.

Following the instructions in this manual will

enable you to obtain optimum performance and

listening enjoyment from your new speaker

system.

Please retain this manual for future reference.

• The speaker cabinet is made of wood and is

therefore sensitive to extreme temperatures and

humidity. Avoid placing the speaker systems in

locations subjected to direct sunlight, or in smoky

or in humid places, such as near an air conditioner,

humidifier, bathroom, or kitchen. Doing so may

result in damage to the speaker.

• Place the unit on a rigid, level surface. Placing it

on a slanted surface or weak base not only may

cause the unit to fall, but also results in decreased

sound quality.

• Be sure to turn off your amplifier before

connecting the speaker system. Connecting them

with the amplifier’s power on may result in

damage to the amplifier or the speaker system.

• Keep water or other liquids away from the unit. If

water is spilled into the unit, not only the unit but

also the speakers themselves may be damaged.

• This speaker system can handle the specified

input power when it is used for ordinary music

reproduction. If the following abnormal signals

are fed to the speaker, however, an overcurrent

may flow in the internal circuits, causing burning

or breakage of the wires even if the input power is

below the specified rating.

1. Noise produced when FM station is not tuned in

2. Sound produced when fast-forwarding cassette

tape deck

3. High-frequency sound generated by an

oscillator, an electronic musical instrument, etc.

4. Oscillating amplifier signals

5. Special test signals produced by audio checking

CD, etc.

6. Sound produced when connecting or

disconnecting audio connection cables (Always

turn off the amplifier’s power before connecting

or disconnecting cables.)

7. Howling when a microphone is used

• Do not place magnetic objects such as

screwdrivers and iron parts near the tweeter since

they use speakers with strong magnets. Otherwise,

the objects may be attracted, causing injury or

damaging the diaphragm.

Before using this unit

Precaution on use

• The two speakers are identical, so it doesn’t matter

which one you use on the left or right.

• Turn the sound volume to the minimum and

disconnect the power cord from the amplifier before

connecting the speaker cables.

• The nominal impedance of this speaker system is

6 Ω. Use only amplifiers capable of handling this

impedance.

• Use the supplied speaker cables to connect between

speaker’s input terminals and the amplifier’s speaker

terminals as illustrated on the below

• Use the red line wires to connect the positive (+)

terminals.

• Connect the speaker cables

securely to the terminals, with

the core wires twisted properly.

In this case, make sure that the

core wires do not touch each

other. Note that a short circuit in

core wires may result in damage

to the amplifier.

Connecting to AV amplifier

Before turning on the amplifier’s power switch:

• Make sure that the positive (+) and negative (–)

speaker cables do not contact each other. Otherwise, a

short-circuit may occur, causing damage to the

amplifier.

• Be sure to connect the speaker cables with correct

polarity (connect the speaker’s positive (+) and

negative (–) binding posts with the amplifier’s

corresponding speaker terminals). Reversed polarity

results in impaired bass-range reproduction, causing

mislocalization of the sound image. Also, be sure to

connect the Right and Left speakers with the

amplifier’s corresponding speaker terminals.

• Pull lightly on the speaker cables to ensure that they

are connected firmly.

The sound quality a speaker system reproduces varies

greatly depending on the construction and area of the

room where it is installed, as well as the location and

size of the furniture. For better-quality sound, observe

the following precautions.

• Avoid placing the speaker system on an elevated

object such as on concrete blocks. Instead, place it on

a rigid floor surface with minimal vibration. Also

note that high-quality bass cannot be obtained if the

speaker system is unstably positioned. Generally

speaking, placing the speaker system on several

small-diameter supports results in better bass than

placing it directly on the installation surface.

Moreover, if you feel the bass reproduced by the

system is too weak, move the speaker system closer

to the wall behind it. You can thus control the

strength of the reproduced bass by the position of the

speakers.

• In many rooms, the furniture and wall affect the

reproduced sound quality. For stereo sound

reproduction, placing the Right and Left speakers in

the same condition produces the best results. If they

are placed in extremely different conditions, the

Right- and Left-channel balance will be adversely

affected.

• The ideal placement of the speaker system is as

follows: Imagine an equilateral triangle and position

the Right and Left speakers on both ends of the base.

The ideal listening position is at or slightly to the rear

of the triangle apex.

• Glazed doors or surrounding walls in front of the

speaker system may cause the resonance of specific

frequency ranges due to reflected sound. To eliminate

this resonance, place some sound-absorbing material

such as a thick curtain in front of the doors or walls.

Connections

SURROUND BACK

SPEAKER SURROUND

SPEAKERS FRONT

SPEAKERS A CENTER

SPEAKER

+–

+– +–

15 mm

+–+–

1. Strip the insulation of speaker cables,

and twist the core wires tightly.

2. Loosen the terminal screw and insert

the wire into the hole (until the core

wires are inserted fully).

3. Fasten the terminal screw.

SKF-4800

Front right speaker SKF-4800

Front left speaker

SKC-4800

Center speaker

AV amplifier

SKR-4800

Surround right

speaker

SKR-4800

Surround left

speaker

Red line

Placement

Using spacers

Affix four of the supplied spacers to the speaker.

Note:

• When you lay the speaker on the floor, be sure to

have another person support it.

• Use a blanket or cushion to avoid scratches.

This speaker system uses

detachable grilles. Use the

following method to attach or

detach the grilles.

1. While holding the bottom edge of the speaker grille

with your both hands, pull it gently toward you to

remove the bottom of the grille.

2. In the same way, gently pull the upper edge of the

speaker grille toward you with your both hands to

remove it from the main unit.

3. To replace the grille, push the projections at the

corners into the grille plug holes on the speaker

cabinet.

Note:

Be careful to not to break the grille.

In general, Braun tubes used for color TV sets, etc. are

extremely sensitive and can be affected even by the

magnetism of the earth. If a speaker system is used near

them, therefore, discoloration or distortion of pictures

will occur. Try moving the speakers away from your TV

sets. If discoloration should occur, turn off your TV

sets, wait 15 to 30 minutes, and then turn it back on

again. This normally activates the degaussing function,

which neutralizes the magnetic field, thereby removing

any discoloration eﬀects.

Your Onkyo speakers are finished with a very high

quality polymer laminate covering that serves to protect

the wood speaker cabinet.

Wipe the cabinet periodically with a dry, silicon-

embedded or plain soft cloth.

The covering may be cleaned with a soft cloth

moistened with water and a mild soap. Avoid the use of

furniture polishes or harsh cleansers. Use a soft brush or

hand vacuum cleaner to remove dust and lint from the

grille material.

Type: 2-way Bass Reflex

Impedance: 6 Ω

Maximum input power: 130 W

Output sound pressure level

: 86 dB/W/m

Frequency response: 55 Hz–35 kHz

Crossover frequency: 3 kHz

Cabinet capacity: 40 L

Speaker: 16 cm Cone Woofer x 2

2.5 cm Soft-dome Tweeter

Dimensions: 295 (W) x 1024 (H) x 305 (D) mm

(Overall dimensions)

Weight: 13.0 kg (/speaker)

Accessory: 3.5 m speaker cable x 2

Instruction manual

Cork spacer x 8

Specifications and appearance are subject to change for

improvement without prior notice.

Bottom of the

SKF-4800

Spacer

Attaching and detaching the speaker grilles

Removal Replacement

Use with a TV set

Speaker care

Specifications

Specyfikacje produktu

Marka:	Onkyo
Kategoria:	głośnik
Model:	SKF-4800

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Onkyo SKF-4800, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Onkyo

Onkyo D-407M Instrukcja

16 Września 2024

Onkyo HTP-2S Instrukcja

10 Września 2024

Onkyo SKS-4700 Instrukcja

9 Września 2024

Onkyo SKS-3600 Instrukcja

4 Września 2024

Onkyo D-407F Instrukcja

3 Września 2024

Onkyo D-309H Instrukcja

3 Września 2024

Onkyo SKS-HT230 Instrukcja

30 Sierpnia 2024

Onkyo SKR-L500 Instrukcja

29 Sierpnia 2024

Onkyo SKS-101 Instrukcja

29 Sierpnia 2024

Onkyo Smart Speaker G3 VC-GX30 Instrukcja

28 Sierpnia 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025

ION Insta Sound Instrukcja

15 Stycznia 2025

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025

Yamaha WX-010 Instrukcja

15 Stycznia 2025

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025