Instrukcja obsługi Olivetti d-Copia 120D

Olivetti drukarka d-Copia 120D

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Olivetti d-Copia 120D (81 stron) w kategorii drukarka. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/81
The ENERGY STAR program is an energy reduction plan introduced by theUnited States
Agency in response to environmental issues and for the purpose of advancing the deve
more energy efficient office equipment.
ENERGY STAR is a U.S. registered mark.
Your attention is drawn to the following actions which could compromise the conformity
as the characteristics of the product:
• incorrect electrical power supply;
• incorrect installation, incorrect or improper use or use not in compliance with the warn
User’s Manual supplied with the product;
• replacement of original components or accessories with others of a type not approved
performed by unauthorised personnel.
All rights reserved. No part of this material may be reproduced or tr
form or by any means, electronic or mechanical, including photocopy
by any information storage and retrieval system, without permissio
the Publisher.
1
CAUTIONS
Caution label on the unit
The label ( ) in the fusing area of the unit indicates the following:
: Caution, risk of danger
: Caution, hot surface
Cautions on using the unit
Follow the cautions below when using this unit.
Warning:
The fusing area is hot. Exercise care in this area when removing misfed paper.
Do not look directly at the light source. Doing so may damage your eyes.
Do not switch the unit rapidly on and off. After turning the unit off, wait 10 to 15
seconds before turning it back on.
Unit power must be turned off before installing any supplies.
Caution:
Place the unit on a firm, level surface.
Do not install the unit in a humid or dusty location.
When the unit is not used for a long time, for example for consecutive holidays,
turn the power switch off and remove the power cord from the outlet.
When moving the unit, be sure to turn the power switch off and remove the power
cord from the outlet.
Do not cover the unit with a dust cover, cloth or plastic film while the power is on.
Doing so may prevent heat radiation, damaging the unit.
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
Important points when selecting an installation site
Do not install your unit in areas that are:
damp, humid, or very dusty
exposed to direct sunlight
poorly ventilated
subject to extreme temperature or humidity changes, e.g., near an air conditioner
or heater.
Be sure to allow the required space around the
machine for servicing and proper ventilation.
A small amount of ozone is produced within the unit during
operation. The emission level is insufficient to cause any health hazard.
Note:
The present recommended long term exposure limit for ozone is 0.1ppm (0.2mg/m 3) calculated
as an 8hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable
to place the unit in a ventilated area.


Specyfikacje produktu

Marka: Olivetti
Kategoria: drukarka
Model: d-Copia 120D

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Olivetti d-Copia 120D, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje drukarka Olivetti

Instrukcje drukarka

Najnowsze instrukcje dla drukarka

Kyocera

Kyocera ECOSYS P2135dn Instrukcja

15 Października 2024
OKI

OKI C920WT Instrukcja

15 Października 2024
Brother

Brother DCP-J152W Instrukcja

15 Października 2024
Sharp

Sharp MX-M7570 Instrukcja

14 Października 2024
Ricoh

Ricoh P C300W Instrukcja

14 Października 2024
OKI

OKI MC851dn Instrukcja

13 Października 2024
Kyocera

Kyocera TASKalfa 8052ci Instrukcja

13 Października 2024
Epson

Epson Mobilink TM-P20II Instrukcja

13 Października 2024