Instrukcja obsługi Oliveri VE590FBN-P
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Oliveri VE590FBN-P (2 stron) w kategorii Dźwig. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Venice
T S MIXER TAP MUST BE INSTA ED BY A LICEN D PLUMBER IN HI LL SE
ACCORD CE WITH LO L EGULATIONS. AN CA R
This Oliveri tap is manufactured to standard AS/N 3 . ZS 718
MAX OPERATING PRE URE: .. . . . . . ... . . . . .. 5 bar ( 0kPa) SS .... ... ... .... .... ... .... .. .... .. .. .... .. .. .. .. .. .... .. .. .. .. .. .... 50
RECOMMENDED OPERATION PRESSURE: .. .. .... .... .... .. .. .. .. .. ... . . . . ... . .. .. . . . ..... .. ... .. ... .. ... . 1.5-5 bar (150- 0kPa) 50
MAX HOT WATER TEMPERAT E: UR .. .. .... .... .... .. .. .. .. .. .. .. .. .. .. ... . . . . ... . .. . .. .. ... .. .... . . .. .. .. .. .. 65°C
RECOMMENDED HOT WATER TEM RATURE: PE .. .. .... .... .... .. ... . . . . ... .. .. ... .. ... .. ..... . . . . . ..... 50°C
Where water pressure exceeds 500kPa, a pressure reducing device is required to be installed Note that water .
pressure overnight can reach 150% of the daytime pressure.
Note: Installation of aerators containing flow regulators: Upon re-installation, the aerator should be tightened
with an aerator key to prevent removal by hand.
Note: Ceramic Cartridges: Warranty claims will not b honoured where the ceramic cartridge has e
malfunctioned due to the presence in the water supply of:
• Copper tube piece sand, dirt or stones s,
• Thread tape
• Other objects not normally present in potable water s es. uppli
Do not remove the cartridge from the body as it has been pressure tested and tightened to a
specific torque.
Before attempting any work involving ains water supply lines, ensure the water supply is shut off. m
Stop valves (preferably with filters) must be used when installing your Oliveri mixer to allow isolation (not
supplied with mixer). Failure to do so where required will void warranty.
This mixer tap is already pre-a embled and tested. Do not dis mble, as this may void the warranty. ss asse
Thi mixer tap must be installed in a ordance with these instructions. s cc
O veri Solutili ons Pty Ltd ABN 12 007 551 886
51 Naweena Rd, Rege y Park SA nc 5010 P 08 8348 6444 E sales@o eri.coliv m.au
Issue Date 12/03/ 022 3 Revision Number: V1.0
VE VE VE590CR-P / 590MB-P / 590BN-P
CARE & MAIN CE TENAN
Clean with a soft cloth and warm soapy water as nece ary - rin and dry after cleaning. Under no ss se
circumstances should abrasive or acid based cleaning products be used.
WA TY RRAN
PRODUCT CO ONENTMP DOMESTIC USE CO ERCIAL USEMM
Kitchen Tapware
London
Car idgetr 10 years replaceme pa s,nt rt
1 year labour
7 years replaceme pa s,nt rt
1 year labour
Body 7 years replaceme pa s,nt rt
1 year labour
1 years replaceme pa s,nt rt
& labour
Finish (chrome) 5 CR-PVE 90 7 years replacement pa s, rt
1 year lab rou
1 year replacement parts
& labour
Finish (Other) 5 N-P,VE 90B
VE5 MB-P90
5 years replacement pa s,rt
1 year lab rou 1 year replacement parts
& labour
Subject to the terms contained in the full warranty information available at https://oliveri.com.au ervice-and- /s
warranty, where a genuine manufacturing defect arises within the warranty period Oliveri will, at its election,
repair the defect or replace the product.
This warra y does not cover against n mal wear and will be vo ed if the product is misused nt or id
o installed in accordance with these instructions. r not Note: Fitting spout-attached devices, including
water filters, to this mixer will void warranty.
Our good co with guarantees that cannot be excluded under the Australian Consumer Law. You are s me
entitled to a replacement or refund for a major failure and for compen tion for any other reasonably sa
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
SERVICE
If the problem represents a danger, or damage to property may occ , immediately shut off the ur
water s ly. upp If the mixer tap require servicing, pl se contact your plumber (preferably the one who s ea
installed it). Most problems occur due to contaminated supply lin or water pressure exceeding 500k . es Pa
Unscrew and clean the spout aerator periodically - especially if you notice a drop in water pressure.
If the Plumber / Insta er is satisfied that the pr lem i t e tll ob s no du o poor insta all tion, contact Oliveri’ minated s no
Warranty Service Agent for a istance on: ss
Ph: (08) 8348 6444 (choose the after sa esl service & wa an rr ty op onti )
E il: warranty@oliveri.com.au ma
For full warranty information visit: h ps://ott liveri.com.au/service-and-wa anty rr
If a warranty service call fi s thand t the spout does not have a genuine manufacturing fault, our
Warranty Service ent reser s the ri t to pass on any call-out fee to the householder. Ag ve gh
Insta ation ll Inst ctionsru
Tec icalhn Data
Pull Out Swivel Mixer
Issue Date 12/03/2023
Revision Number: V1.0
Installation Instructions
Max 37
INSTA ATION IN RUCTIONS LL ST
General Note: This product is to be installed by a licensed plumber, installation must comply with
AS/NZS 3500 and local plumbing c es. od
Pressures & Temperatures
Maximum Hydrostatic Pressure – 500 k . (As per AS/NZS 3500). Pa
Note: AS/NZS 3500.1-2003 (Clause 3.3.4) states that “Provision shall be made to ensure that the
maximum static pressure at any outl , et other than a e service outlet, within a building does fir
not exceed 500 kPa.
Note: Pressures above 500kPa can cause damage om water hammer, reduced life of appliances, fr
taps a fit s, and cause excessive noise in the system. nd ting
Minimum Hydrostatic Pr sure – 100 kPa. The Maximum operating temperature for the mixer tap is 65 °es C.
Please ens e that the lines are flushed prior to installation as contaminates in the water can damage ur
the ceramic cartridge, flow reg a r and also affect the peul to rformance of the Mixer.
1. Remove product from packaging and check for damage, if the product is d aged do not am
install and return to store of purchase.
2.. The WELS compliant aerator has been pre-a embled into the mixer outlet. To comply with WELS the ss
flow regulator must re in in place. ma
3. Ensure Product is complete as per exploded drawing.
4. A single 35mm hole is required in the mounting surface.
5. The maximum mounting surface thickness cannot exceed 37 mm.
6. Ensure bench sealing washer (A) is in place on base of the Mixer.
7. Firmly screw the Mixer Tails (C) into base of the Mixer being careful to avoid damage to the o'ri ng
seals, the Mixer Tails are colour coded, red for hot and blue for cold, the Mixer base inlet holes are
stamped with "H' for hot and 'C' for cold, or red mark for hot and blue mark for cold.
8.
9.
Feed the Mixer Tails (C) and (L) through the mounting surface each Tail alternately. Feed the Braided
Ho through the mountinse g surface and the Stabiliser Plate (B), and position the mixer on the mounting
surface ensuring the Dress Ring (A) and Stabiliser Plate (B) are positioned correctly.
10.
Slide Rubber Seal (E) onto the threaded inlet tube followed by Metal Plate (F).
N.B The Mixer Tails should be positioned towards the user and the Fixin Inlet tube to the back. g/
11.
Using Fixing Nut (G) tighten Mixer to the mounting surface.
12.
Screw Dual Check Valve (H) to end of Inlet Tube (D ensuring sealing washer (l) is in place. )
13.
Screw male threaded end of Braided Hose (L) into Hose Dual Check Valve (H) ensuring sealing washer (J) is in place.
14.
Connect Mixer Tails (C) to mains water supply line.
15.
N.B Ensure the Mixer Tails are not kinked, bent, stretched or wisted when assemb t ling to the mains
water s ly. The Mixer Tail connection between the Mixer and the water supply must have a upp
natural curve. Ensure Mixer Tails are not exposed to abrasi s, corrosive agents the likeon or .
16.
It is reco nded that In-Line filters be installed to ensure a cleaner flow of water to the Mixer. mme
17.
The Braided Mixer Hose (L) will have a natural curve under the mounting surface On the hand piece side of .
the curve, fit the Return Weight (M) using the two screws provided. Fit the Weight approximately 100 mm
up from the bottom of the curve on the hand piece side, the position can be adjusted to suit but the
weight must remain on the hand piece side of the curve.
Pull the hand piece (K) out from the Mixer to test hose extension, release the hand piece (K) to ensure that
it return accurately back into the Mixer cradle. s
TO THE CONS ER UM
1. The Mixer i to only be cleaned with warm soapy water and a soft cloth. s
2. Under no circumstances should any abrasive, cream or acid based cleaning agents be used, as th e es
typ of cleaners can damage th finish, cartridge, seals and Mixer aerator. es e
K
C
D
E
F
G
A
Braided flexible hoses
must be inspected
every 12 months for
warning signs of failure
including bulging, rust
spots, wear, moisture,
snapped threads,
kinking, water staining,
general corrosion or
discolouration.
Mixer tails showing any
signs of the above
mentioned warning
signs must be replaced
immediately.
H
B
I
J
M
L
Specyfikacje produktu
| Marka: | Oliveri |
| Kategoria: | Dźwig |
| Model: | VE590FBN-P |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Oliveri VE590FBN-P, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Dźwig Oliveri
7 Października 2024
7 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
Instrukcje Dźwig
- Dźwig Ikea
- Dźwig Teka
- Dźwig Smeg
- Dźwig Etna
- Dźwig Lamona
- Dźwig Berg
- Dźwig Nodor
- Dźwig Grohe
- Dźwig Axor
- Dźwig CDA
- Dźwig Delta
- Dźwig Franke
- Dźwig Inventum
- Dźwig Livarno Lux
- Dźwig Caple
- Dźwig Hansgrohe
- Dźwig Sussex
- Dźwig Deante
- Dźwig Miomare
- Dźwig BLANCO
- Dźwig Ernesto
- Dźwig Elba
- Dźwig Schütte
- Dźwig Elkay
- Dźwig Quooker
- Dźwig Lynx
- Dźwig Empire
- Dźwig Moen
- Dźwig Aloni
- Dźwig WillieJan
- Dźwig Sani-Lav
- Dźwig Brauer
- Dźwig Fala
- Dźwig Neo
- Dźwig Lomazoo
- Dźwig Vola
- Dźwig Zip
- Dźwig The Galley
- Dźwig Oras
- Dźwig Viidako
- Dźwig Curaqua
- Dźwig Waltec
- Dźwig Fantini
- Dźwig Rogerseller
- Dźwig Gessi
- Dźwig Graff
- Dźwig Zurn
Najnowsze instrukcje dla Dźwig
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024