Instrukcja obsługi Oliveri SB35BK
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Oliveri SB35BK (2 stron) w kategorii Zlew. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Template suits:
SB35SS
SB35GM
SB35CU
SB35BK
For topmount and undermount installation instructions see reverse.
For flushmount installation refer to your installer.
Digital templates are available at oliveri.com.au
Template suits:
SB63SS
SB63GM
SB63CU
SB63BK
Template suits:
SB50SS
SB50GM
SB50CU
SB50BK Care instructions for you coloured Oliveri stainless steel sink
AVOID CONTACT WITH ROUGH OR DIRTY SURFACES as new polished stainless steel will show scratches!
• Coloured sinks should only be cleaned with soapy water and a soft cloth or sponge, then rinsed and towelled
dry.
• The colouring is a solid coating (Physical Vapour Deposit) on the surface of the stainless steel only - harsh
scratching should be avoided.
• It is highly recommended to use the wire bowl protector provided with the sink, to protect the bottom of the
bowl
• Never use steel wool in or on the sink (steel wool should be avoided with any stainless steel sink, as it can leave
steel deposits on the sink, which can cause rust).
• Never use harsh abrasive cleaning pads to clean coloured sinks.
• Never use harsh chemicals or bleaches to clean coloured sinks.
• Do not store harsh chemical (acids, chlorines, bleaches etc.) under the sink, as the vapours (even from the closed
containers) can cause rusting on the underside of the stainless steel sinks.
• Avoid prolonged contact with ordinary steel containers (e.g. tin cans), as these can rust and stain the sink.
• Avoid prolonged exposures to acids from fruit, fruit juices, salts, tea bags etc., as these may leave stains.
• Avoid leaving liquid soaps, hand sanitizing liquids etc. to dry on the surface of the sink, as these may leave stains.
Coloured Stainless Steel Care Guide
IT IS HIGHLY RECOMMENDED THAT THE ACTUAL SINK BE PRESENT AT TIME OF INSTALLATION
All cut-out templates are available online at oliveri.com.au
It is essential that the installation is waterproof and carried out in accordance with these instructions.
Tasman Sinkware will not be held responsible for any damage caused by leakage or faulty installation.
CHECK YOU HAVE THE CORRECT MODEL SINK
The model number on the sink packaging must match the model of sink
the customer ordered. Do not install if incorrect.
AVOID CUTS
The perimeter and punch-outs on the sink may contain sharp edges.
Handle the sink carefully to avoid personal injury.
CHECK THE CONDITION OF THE SINK BEFORE INSTALLATION
Do not install if defects are found – contact your retailer / point of purchase.
By installing the sink, the owner / installer accepts that the product is free
of defects – Tasman Sinkware shall not be liable for any expense incurred
relating to the removal or replacement of a defective product.
AVOID SCRATCHES
Stainless steel can be scratched if proper care is not taken during
installation.
Any advice, recommendation, information, assistance or service provided by in relation Oliveri Solutions
to goods manufactured by it or their use and installation, is given in good faith and is believed by Oliveri
Solutions to be appropriate and reliable. However, any advice, recommendation, information, assistance
or service is provided by without responsibility or liability.Oliveri Solutions
Australia (Head Office)
Oliveri Solutions Pty Ltd
ABN 12 007 551 886
PO Box 2141 Regency Park
SA 5942 Australia
P 61 8 8348 6444
F 61 8 8348 6495
E @oliveri.com.ausales
New Zealand
Fletcher Building Products Ltd
PO Box 4641 Christchurch
New Zealand 8140
P 0800 440 606
F 0800 440 532
E s @oli .com.auales veri
Stainless Steel Sink Installation Guide
Spectra Cut Out Templates
TF153 - Spectra Installation and Care Instructions.pdfd
Check Space & Level
Use a level to check the counter/benchtop – if not level, have rectified. Ensure there is adequate space
for tapware (including a splash back if specified). Check space for installation (underneath) and operation
(above). Particular care must be taken when a thick splash back is used (it may interfere with tapware
location and operation). Ensure the cabinet will not foul the sink mounting flange or basins.
Template *
Template supplied in carton is for undermount installation only. For digital templates or topmount
installation templates visit oliveri.com.au.
IF COUNTER / BENCHTOP IS SUPPLIED WITH CUT-OUT, SKIP STEPS MARKED WITH*
Mark Cut Out *
Carefully mark out the template (or follow drawing instructions). Once the hole is marked out, use the
template to conduct a final check before cutting.
IMPORTANT
For topmount sinks only, you can trace the sink itself to mark your cut out, the hole must be cut 10mm /
3/8” inside the marked line.
Cut & Finish Hole *
Re-check the position and cut out shape you have traced before cutting. Ensure there are no obstacles
below that might interfere with cutting. Drill pilot holes to accept an appropriate cutting tool for the
counter/benchtop material (wear suitable personal protection equipment).
Masking
If using a sealant, masking is necessary to prevent sealant overrun. It is recommended that the edge of
the sink and the edge of the cutout are both covered with a suitable masking tape. This tape should be
removed within 2 days of application.
Trial Fit The Sink
Check that all clips are folded in so they will adequately clear the cut-out. Carefully position the sink into
the cut-out to make sure it fits correctly. If the fit is not correct, remove the sink and proceed with remedial
work. Perform another trial fit after corrections have been made.
Apply Sealant
Apply suitable sealant recommended for both the counter/benchtop material being used and for stainless
steel. Neutral-cure sealant will not damage stainless steel. It may be easier to apply sealant after preparing
your clamping equipment. Do not allow the sealant to dry before the sink is clamped to the counter/
benchtop.
Plumbing & Tapware
IMPORTANT - Connections to plumbing should always be done by a licensed plumber.
Fit supplied basket wastes to sink bowls. Install tapware according to manufacturer’s
instructions. Care should be taken when fitting wastes to the sink. Follow the instructions
provided with the wastes.
Additional Sealant (Optional)
Apply additional sealant / caulking compound around the join where the counter/
benchtop and the stainless steel sink meet. Check that the caulking product is mildew
resistant and is suitable for use on the counter/benchtop material and also is suitable
for use on stainless steel. Clean away any excess before it dries. Note: Additional sealant
should always be used if gaps are apparent after the sink has been clamped to the
counter/benchtop
Fitting The Sink
Position and align the sink correctly in the cutout (some threaded rod and timber bearers
will help to clamp the sink in place) and either
‘A’ Sandwich Method: RECOMMENDED FOR BOTH THIN AND THICK COUNTER/
BENCHTOP. Firmly fix a support board into / over the cabinet and cut the sink hole so
that the sink flange will sit above the edge of the board. Slightly rout the edge so that
the sink flange will sit flush with the top surface. Test for fit. Install sink and seal between
flange and support board. Apply sealant to the underside edge of the cutout on counter/
benchtop material and position it over the support board to sandwich the sink in place.
Fasten the counter/benchtop securely.
‘B‘ Bond: For minimum 1” / 25mm thick material. Bond it to the underside of the
counter/benchtop with a structural high strength epoxy compound. NOT RECOMMENDED
TO BE USED WHEN FITTING SINK TO THINNER COUNTER/BENCHTOPS.
‘C‘ Bolt: For minimum 1” / 25mm thick material. Bolt it to the counter /benchtop
using “molly” assemblies. Care must be taken during drilling and tightening to avoid
cracking. NOT RECOMMENDED TO BE USED WHEN FITTING SINK TO THINNER COUNTER/
BENCHTOPS.
If you have any doubts, confirm the correct mounting method for your material by
consulting the counter/benchtop supplier.
Above shows sandwich method
where sink is clamped between a
lower support board (with routed
edge) and the upper counter /
benchtop using method A.
Above shows how threaded rod
and timber bearers may be used
to clamp the sink in place while
fastening to the counter / benchtop
using methods B and C.
Do not overtighten as this may
damage the sink.
Counter / benchtop
Sealant
Sink flange
Support board with routed edge
(such as timber)
A
Counter / benchtop
Sealant
Sink flange
Epoxy
B
1” Counter / benchtop with hole drilled
Molly
Sealant
Sink flange
Saddle
Screw
C
UNDERMOUNT ONLY
Fitting The Sink
Position and align the sink correctly in the cutout and lower it onto the counter/benchtop.
From underneath, install and tighten the clips with a screwdriver using a suitable
tightening sequence (tighten from the centre of the sink to the outer edge) until the sink
is secure and no gaps are visible. Take extra care if using power tools as over-tightening
can damage clips. The clips included with the sink require a minimum counter/benchtop
thickness of 1” / 25mm. If fitting into a thinner bench top, timber blocks or similar should
be installed between the bench top and the clip.
TOPMOUNT ONLY
Stainless Steel Sink Installation Guide
TF153 - Spectra Installation and Care Instructions.pdfd
Specyfikacje produktu
| Marka: | Oliveri |
| Kategoria: | Zlew |
| Model: | SB35BK |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Oliveri SB35BK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Zlew Oliveri
3 Października 2024
3 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
Instrukcje Zlew
- Zlew Teka
- Zlew Smeg
- Zlew Concept
- Zlew Nodor
- Zlew Hotpoint Ariston
- Zlew CDA
- Zlew Artusi
- Zlew Franke
- Zlew Caple
- Zlew Kernau
- Zlew Foster
- Zlew Deante
- Zlew BLANCO
- Zlew Rangemaster
- Zlew Leisure
- Zlew Elkay
- Zlew Schock
- Zlew Roca
- Zlew Advance Tabco
- Zlew Sani-Lav
- Zlew Laveo
- Zlew Tot Mate
- Zlew Kuchinox
- Zlew Shaws
Najnowsze instrukcje dla Zlew
14 Października 2024
13 Października 2024
13 Października 2024
13 Października 2024
13 Października 2024
4 Października 2024
4 Października 2024
4 Października 2024
4 Października 2024
4 Października 2024