Instrukcja obsługi NetworX NX-584 HOME AUTOMATION MODULE

NetworX Bezpieczeństwo NX-584 HOME AUTOMATION MODULE

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NetworX NX-584 HOME AUTOMATION MODULE (12 stron) w kategorii Bezpieczeństwo. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

NX-584 HOME AUTOMATION MODULE

Installation Manual

These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to be

met during installation, operation, and maintenance. If further information is desired or if particular problems arise that are not

covered sufficiently for the purchaser’s purpose, the matter should be referred to GE Interlogix, Gladewater, Texas, USA.

This document contains proprietary information of GE Interlogix, USA and is furnished to its customer solely to assist that

customer in the installation, testing, operations, and/or maintenance of the equipment described. This document shall not be

reproduced in whole or in part nor shall its contents be disclosed to any third party without the written approval of GE Interlogix.

Please refer to the current GE Interlogix product catalog for detailed warranty information.

TABLE OF CONTENTS

I. GENERAL DESCRIPTION .................................................................................................2

II. TERMINALS & PIN-OUT....................................................................................................2

III. ENCLOSURE DIAGRAM....................................................................................................3

IV. WIRING DIAGRAM.............................................................................................................4

V. ENROLLING THE MODULE...............................................................................................4

VI. PROGRAMMING THE MODULE........................................................................................5

VII. PROGRAMMING DATA .....................................................................................................5

VIII. LEDS INDICATORS............................................................................................................6

IX. PROGRAMMING LOCATIONS..........................................................................................7

X. PROGRAMMING WORKSHEETS....................................................................................10

XI. SPECIFICATIONS ............................................................................................................12

NX-584 Home Automation

I. GENERAL DESCRIPTION

The NetworX NX-584 is a low cost add-on module that fits neatly into any NetworX family system

enclosure and provides a standard RS-232 bi-directional DB-9 connector for connection to a home

automation host system. A simple three-wire connection to the main control is all that is required to

fully integrate this card into the system.

The NX-584 has several levels of security that can be programmed in at the time of installation to

allow as much or as little security system information to be passed to the host system. It can also be

set to limit the commands that will be accepted from the host system to prevent unauthorized

attempts to override the security system status.

The unit can be easily configured for communication in an ASCII or Binary protocol. A selectable

baud rate can be set from 600 baud to 76.8k baud with hardware RTS and CTS handshaking. The

ASCII implementation is easy to use and debug with standard programming tools while the Binary

version is a more efficient for method for transferring information between the two systems. The

system integrator can select any number of events or conditions to cause the NX-584 to send the

relevant information to the host without polling. This allows for a faster response to activity than

polling alone can provide.

All security system information can be requested at anytime if enabled to do so by the installer. This

is useful at system initialization and at periodic intervals to keep the two systems in sync without

worrying about missing any transitional event. This information is organized as System, Partition,

Zones and Outputs. System information will contain such information as power status, phone line

condition, module troubles, and other system wide condition. Partition information includes readiness

of all zones assigned, armed state, entry / exit delays, last user number, alarm condition and many

other conditions within a specific partition. Zone information includes faults, alarm memory, bypasses,

troubles, tampers, low batteries, missing and partition assignments. Output messages include

commands that can be passed to or from devices in X-10 compatible format.

II. TERMINALS & PIN-OUT

TERMINAL DESCRIPTIONS

POS Connect to the KP POS terminal of the NX-8

COM

Connect to the KP COM terminal of the NX-8

DATA

Connect to the KP DATA terminal of the NX-8

NX-584 Home Automation 3

DB-9 Pin-out Pin Number Signal

Name Direction

NX------PC Jumper

Number A Position B Position

Cts* → J7 8** 7

Txd → J8 2 3**

Rts* ← J9 8 7**

Rxd ← J10 2** 3

Sig.Gnd. ←→ -- 5

Unused -- -- 1,4,6,9

*Note: Rts and Cts signals are not currently supported

**Note: Default jumper settings

III. ENCLOSURE DIAGRAM

Inside the can, several 2-holed insertion points have been

constructed. This allows for either vertical or horizontal placement of

the modules. Notice that the insertion points have two sizes of

holes -- a larger hole and a smaller hole.

Diagram 1: The black plastic PCB guides are grooved on one edge

where the PC Board will be seated. The end with the half-moon

protrusion fits into the larger hole. The smaller hole is for the screw.

Diagram 2: Place the first black plastic PCB guide in the top insertion

point, grooved edge downward. The half-moon protrusion will be in

the large hole. It does not require force. Insert one of the provided

screws into the smaller hole (from inside the can) to secure it in place.

A screwdriver should reach through the notch that runs the length of

the guide to tighten the screw. The second PCB guide should be

positioned opposite of the first (grooved edge up) and placed in the

lower insertion point, using the same procedures described above.

Once mounted, screw it in securely.

Diagram 3: The PC board should slide freely in the grooves of both

guides.

Specyfikacje produktu

Marka:	NetworX
Kategoria:	Bezpieczeństwo
Model:	NX-584 HOME AUTOMATION MODULE

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z NetworX NX-584 HOME AUTOMATION MODULE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Bezpieczeństwo NetworX

NetworX NX-595E IP Communication Module Instrukcja

5 Października 2024

NetworX NX-124E Instrukcja

23 Września 2024

NetworX NX-108E Instrukcja

21 Września 2024

NetworX NX-4 Instrukcja

20 Września 2024

NetworX NX-408 Instrukcja

20 Września 2024

NetworX NX-448 Instrukcja

9 Września 2024

NetworX NP0098.1 Instrukcja

7 Września 2024

NetworX NX-10 Instrukcja

7 Września 2024

NetworX NX-6V2 System Keypad Instrukcja

6 Września 2024

NetworX NX-4SE Instrukcja

5 Września 2024

Instrukcje Bezpieczeństwo

Najnowsze instrukcje dla Bezpieczeństwo

Aritech SHATTERPRO 3 Instrukcja

15 Stycznia 2025

Axis Camera Station S9001 Mk II Desktop Terminal Instrukcja

15 Stycznia 2025

Eminent EM6511 Instrukcja

15 Stycznia 2025

Ranex RX2567-Z Instrukcja

11 Stycznia 2025

Technaxx TX-106 Instrukcja

11 Stycznia 2025

Geemarc SOS-PRO 295 Instrukcja

2 Października 2024

One2track Safety Angel Instrukcja

28 Września 2024

Sygonix SY-3851632 Instrukcja

28 Września 2024

Sygonix 1326052 Instrukcja

28 Września 2024

Sygonix 43588A WLAN Camera Instrukcja

28 Września 2024