Instrukcja obsługi Muse M-1015

Muse Radia samochodowe M-1015

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Muse M-1015 (2 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Detach the Front Panel

Press button in the upper left corner, and then the front panel will be folded down.

(release button)

PWR (Power button)

9/ button (Skip forward)

7/MODE button

SEL/VOL knob (Audio / volume)

AMS/SCH button (Automatic

storing)

TA button (Trafﬁ c alarm)

disc slot

LCD display

(Eject button)

USB slot

AUX in jack

0/DSP button (Display time)

6/DIR+ button (Directory up)

5/DIR- button (Directory down)

4/RDM button (Random)

3/RPT button (Repeat)

2/INT button (Intro)

1/PAU button (Pause)

BAND/LOUD button

PTY button (Program type

selecting)

EQ button (equalizer)

8/ (skip backward)

AF button (Alternative Frequency)

Reset button

SD/MMC slot

Do not attempt to modify the unit, modifying the unit may cause an accident.

Installation or servicing of the unit by persons without training and experience in

electronic equipment and automotive accessories may be dangerous and could

expose you to the risk of electric shock or other hazards.

Stop the vehicle before carrying out any operation that could interfere with your

driving.

Keep the volume at a level which you could hear sounds from outside the vehicle.

Do not work in extremely high or low temperature. Be sure the temperature inside

the vehicle is between +60°C and -10°C before turning on your unit.

When replacing the fuse(s), the replacement must be of the same amperage as

shown on the fuse holder.

Do not block vents or radiator panels. Blocking them will cause heat to build up

inside and may result in ﬁ re.

Using this unit without running the engine can result in battery drainage

Use only in cars with a 12 volt negative ground.

After completing the installation and beginning to play the unit(including replacing

the battery), please remove the front panel at ﬁ rst, and then press RESET button

on the base with pointed object (such as ball-point pen) to set the unit to initial

status.

Before you install the unit, remove absolutely the two transportation screws on top

of the unit.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

10.

11.

M-1015 MR

GB - 1

User Manual

CAR RADIO CD/MP3

PLAYER WITH USB/SD/MMC

Please read the instruction carefully

before operating the unit.

PRECAUTIONS

English

* Do not attempt to load more than one disc.

* Only 12cm discs are compatible.

* New discs may have some roughness around the edges. Before load such disc into

the player, use a ball-point pen or the like to remove any roughness from the edge of

the disc.

* If there is a scratch, dirt or ﬁ ngerprints on the disc, it may cause tracking error. Before

playing, clean the disc with a clean cloth. Wipe the disc from the center out.

* Don’t store discs in places with high temperatures or high humidity, they can become

warped. After playing, store the disc in its case.

GB - 2 GB - 3

CONNECTION

1. Antenna Receptacle

2. Line out Right (red)

3. Line out Left (white)

4. Output plug (male)

5. Output plug (female)

6. FUSE holder (15 A)

Caution!

- Make sure to connect the color coded leads according to the diagram. Incorrect

connections may cause the unit to malfunction or damage the vehicle’s electrical system.

- Make sure to connect the speaker (-) leads to the speaker (-) terminal. Never

connect the left and right channel speaker cables each other or to the vehicle body.

- Make sure all the connections are completely correct before turning on your unit.

Do not connect the ignition wire (red) and the battery wire (yellow), it may cause a short circuit,

even result in ﬁ re.

Install the unit

- Method 1: DIN Front-Mount

1. Remove the outer trim frame

2. Select a position where the screw holes of

the mounting bracket supplied with the car

and the screw holes of the main unit become

aligned (are ﬁ tted).

3. Tighten the screws. And then fasten them to

the car.

GB - 4 GB - 5

Install the front panel

Insert the panel into the housing and make sure the panel is properly installed.

Otherwise, abnormality occurs on the display or some keys will not function properly.

Note: Never put any objects into the front panel.

Detach the unit

1. Detach the front panel. (please refer to upper part)

2. Take out the outer trim frame.

3. Insert the keys supplied to the unit at the both sides of the unit (shown as illustrated)

until they click. Pulling the keys and makes them to remove the unit from the dash-

board.

GB - 6

LOCATION OF CONTROLS

Front panel

Base

GB - 7

Notice on disc

Use such discs may cause malfunction or breakdown of the internal mechanism:

with large scratches; with irregular shape; cracked; with any cellophane tape or other

glue on it or with peeling off marks; with protection sheet; equipped with stabilizers, etc.

- Method 2 DIN Rear-mount (For Japanese car)

BASIC OPERATION

Turning on/oﬀ the unit

Press button (2) to turn on the unit. Press this button again to turn oﬀ the unit.PWR

Note: When the unit is oﬀ, press any key except (1) to turn on the unit.

Selecting the mode

After the unit is on, press (4) button to select diﬀerent sourcing mode: Radio MODE

CD USB SD/MMC AUX

UNPACK YOUR UNIT

When you unpack your new car radio, make sure that you have removed all the acces-

sories and information papers:

Main unit

User manual

Accessories:

INSTALL AND DETACH THE UNIT

SOUND FEATURES

Setting the Sound:

Repeatedly press knob (5) to select the desired mode in the following order: SEL/ VOL

“BAS” (Bass) -> “TRB” (Treble) -> “BAL” (Balance) -> “FAD“ (Fade) ->“BEEP“ (BEEP

ON/OFF) -> “TA VOL“ (TA volume) ->“EON” (EON ON/OFF) -> “VOL” (Volume). After

selecting the desired mode, you can adjust the current level by rotating the SEL/ VOL

knob (5).

- BEEP: under Beep mode, rotate SEL/VOL (5), LCD shows “BEEP ON” or “BEEP

OFF”, choosing corresonding status can turn on or turn oﬀ beep.

- please refer to RDS operationEON:

Note: The unit will return to the previous mode if no adjusting within 3 seconds.

Time display

Press button (13) to show the current time on displayDSP

Adjust time: Long press DSP (13) until clock time with ﬂ ashing hour digits appears.

Then Press and button to adjust the hour value and press DSP (13) to conﬁ rm.

Then minute digits ﬂ ash. Press and button to adjust the minute value and

press (13) to conDSP ﬁ rm

Reset the unit

Operating the unit for the ﬁ rst time or after replacing the car battery, you must reset the

unit. To set the unit to initial status, press RESET button (25) located on the base with

a pointed object. When some errors occur in display, you can also reset the unit, but it

will erase the clock setting and some memorized functions.

Volume adjusting:

To increase or decrease the sound level, rotate knob (5) clockwise or SEL/VOL

anti-clockwise.

2625

Preset equalizer

When you are listening to popular music, classic music or rock music, using EQ

to select relative status can adjust the sound quality. Repeatedly press (8) to select EQ

diﬀerent equalizer mode in following order: FLAT->POP->ROCK->CLASS -> EQ oﬀ.

Switching Loudness On/oﬀ

Press and hold button (20) until “LOUD ON” shows on display to BAND/LOUD

activate LOUD function. By this function, you can increase the low frequency, which

can improve sound sensitivity. Press and hold this button again until “LOUD OFF”to

cancel LOUD function.

NOTE: It will return to normal play mode if no key is pressed within 5 second.

Information display

- In case of receiving a RDS station.

In radio mode: CT -> FREQ ->PTY ->PS

In CD (MP3 / WMA) mode: CD (MP3/WMA) -> CT -> FREQ -> PTY ->PS

- In case of not receiving a RDS station.

In radio mode: CT -> FREQ -> NO PTY -> NO PS

In CD mode: CD -> CT -> FREQ -> NO PTY -> NO PS

1 2 3 5 6 74

8 9 11 1210

M5 X 21

24 23 22 21 20 19 18 17 16 15 14 13 12

2 3 4 5 6 7 8 9 10 11

AR-3045 IB MUSE 001 REV0 GB.indd1 1

AR-3045 IB MUSE 001 REV0 GB.indd1 1AR-3045 IB MUSE 001 REV0 GB.indd1 1 2011-2-28 15:58:30

2011-2-28 15:58:30

2011-2-28 15:58:302011-2-28 15:58:30

12V DC (11-16 V allowable)

40W x4

±10 dB

Bass at 100 Hz

Treble at 10 kHz

Approx. 188 x 188 x 59 mm (d / w / h)

Approx. 169 x 182 x 53 mm (d / w / h)

Approx. 1.2 kg

87.5-108 (MHz)

10.7 MHz

15 dBuV

50 dB

25 dB

70 dB

50 dB

0.1%

20 - 20000Hz

Loading/Remove a disc

Insert the disc into the DISC SLOT with the printed side facing up. The player will play

the disc automatically. If a disc was inserted, press button (4) to start playing. MODE

To remove the disc, press button.

To insert a USB devices (not included)

Open the plastic cover, connect your USB device to the USB slot (11), it will switch to

“USB” mode automatically. If USB has been inserted, press button (4) to switch MODE

to USB mode.

To insert an SD/MMC card (not included)

Press button (1) to fold down the front panel ﬁ rst. Insert your SD/MMC card in

card receptacle (26). Close the front panel and it will automatically start playing. If SD/

MMC card has been inserted, press button (4) to switch to card mode.MODE

CAUTION: Invisible laser radiation when open and interlocks defeated. Avoid

exposure to beam.

WARNING - To reduce the risk of ﬁ re or electric shock, do not expose this appliance to

rain or moisture.

If at any time in the future you should need to dispose of this product please

note that Waste electrical products should not be disposed of with household

waste. Please recycle where facilities exist. Check with your Local Authority

or retailer for recycling advice.(Waste Electrical and Electronic Equipment

Directive)

ATTENTION: To reduce the risk of electric shock, do not remove

the cover. There are no user serviceable parts inside the unit. Re-

fer all servicing to qualiﬁ ed personnel.

GB - 15

LISTENING TO THE RADIO

LISTENING TO DISC/USB/SD

LISTENING TO AUXILIARY SOURCE

1. Connect your auxiliary source (e.g. mp3 player) to the AUX IN jack (12)

2. Press (2) button to turn the unit on.PWR

3. Press (4) to select AUX mode.MODE

4. Start playback from your auxiliary source.

5. Adjust the volume (5) to desired level.

6. Disconnect your auxiliary source from the Aux in jack (12), press MODE button (4)

to select other source.

TROUBLE SHOOTING GUIDE SPECIFICATIONS WARNINGS

GB - 14GB - 13GB - 12

GB - 11GB - 10GB - 9GB - 8

General

Power Requirement

Load Impedance

Max. Power Output

Tone Controls

Dimensions

Mounting Dimensions

Weight Approx.

FM Section

Tuning Range

IF Range

Usable Sensitivity (-30dB)

Signal-to-noise Ratio

Stereo Separation

CD player Section

Signal-to-noise Ratio

Separation

Distortion

Frequency Response

Selecting band

In tuner mode, repeatedly press BAND/ LOUD button (20) to select bands in

following order: FM1->FM2->FM3.

Manual/automatic tuning

- Manual Tuning

Press and hold button or (3/23) until “MANUAL” shows on display, then press

button or (3/23) continuously to select a station downward or upward. Press

and hold button or (3/23)to tune the station with a faster speed.

- Automatic Tuning

Press or (3/23) once, the radio automatically searches a station upward or

downward respectively and plays when it ﬁ nds a station. Press or (3/23)once to

stop scanning.

Alternative frequency (AF)

The AF function switches to a different frequency on the same network in order to

maintain optimum reception. In FM mode, press AF button (24), certain program will be

automatically searched and received. If the reception of the current broadcast station

deteriorates, “AF” appears in the display and the radio searches for the same program

on another frequency. Press button (24) again to cancel this functionAF

Scanning/memorizing stations automatically

- By AMS/SCH button (6)

In tuner mode, press and hold AMS/SCH button for 3 seconds to start scanning for

stations and store them automatically in memory. Press AMS/SCH button (6) the radio

plays each preset station for a few seconds. Press AMS/SCH (6) again or numeric but-

tons 1-6 to listen to corresponding station.

- By number button (14-19) 1-6

1. Tune to a station by or (3/23).

2. Press and hold one of the 1- 6 Number buttons (14-19) for 2 seconds until LCD

shows the corresponding number, which indicates that station is stored in the corre-

sponding number button.

3. Under radio mode, press Number buttons (16-21) to listen to stored stations.1- 6

4. When you are listening to a station stored on a number button, press and hold

another number button for more than 2 seconds to store the station on this number

button.

Note: The unit can be stored up to 6 stations for each band.

-- RDS (Radio Data System) Operations --

This unit has a built-in RDS decoder system that supports broadcast stations

transmitting RDS data. This system can display the name of the broadcast station being

received and can automatically switch to the broadcast station with the best recep-

tion as you travel on long distances (AF switching). A trafﬁ c announcement broadcast

from an RDS station, no matter what mode you are, additionally, if EON information is

received, enables automatic switching of other preset stations on the same network

and interruption of the station being received with trafﬁ c information. This function is

not available in some areas.

Trafﬁ c alarm (TA)

In the TA standby mode, when a traffic announcement broadcast starts, the traffic

announcement broadcast is received as top priority regardless of the function mode so

you can listen to it. Trafﬁ c programme (TP) automatic tuning is also possible.

Press TA button (7), when LCD shows “TA”, traffic program will be automatically

searched and saved, when LCD shows “TP”, this means that the RDS broadcast

station being received has trafﬁ c announcement programmes.

If you press button (7) while a trafTA ﬁ c announcement broadcast is being received,

the trafﬁ c announcement broadcast reception is cancelled and the unit goes into the TA

standby mode.

If a TP station is not received, the unit continues searching.

Press button (7) again to stop searching, “TA” goes oﬀ.TA

ALARM

“ALARM” will be displayed when an emergency broadcasting is received; meanwhile

sound output level will be adjusted to the preset output level automatically when the

volume control is set at minimum.

EON: (Enhanced Other Networks Information)

Press and rotating (5) to select EON mode, EON ON. When receive the SEL/VOL

EON information, the EON indication is on. With EON facility, it oﬀers the ability for lo-

cal stations to”break into” a national station’s broadcast for the duration of a Trafﬁ c An-

nouncement.

Program type selecting (PTY)

When PTY is selected, the radio starts to search corresponding PTY information, and

stops when the corresponding PTY information is detected.

I f c o r r e s p o n d i n g P T Y i n f o r m a t i o n d o e s n o t e x i s t an y m o r e , PT Y i s

automatically stopped to normal mode.

When PTY mode is engaged. The PTY switch is shared as follows:

According to above 2 groups, the preset number is used for PTY selection as follows:

MUSIC group

1. POP M, ROCK M

2. EASY M, LIGHT M

3. CLASSICS, OTHER M

4. JAZZ, COUNTRY

5. NATION M, OLDIES

6. FOLK M

SPEECH group

1. NEWS, AFFAIRS, INFO

2. SPORT, EDUCATE, DRAMA

3. CULTURE, SCIENCE, VARIED

4. WEATHER, FINANCE, CHILDREN

5. SOCIAL, RELIGION, PHONE IN

6. TRAVEL, LEISURE, DOCUMENT

Basic player functions

Play/pause: 1/PAU press (19) to suspend momentarily the playing track. Press (19)

once again to resume playing.

Skip/fast search: press button (3) to skip forward to next track and (23) to skip

backward to previous track. Press and hold or (3/23) to search quickly within a

track.

Intro scan: press 2/INT button (18) when it show “INT ON”, then the player will play

the ﬁ rst 10 seconds of each track in the disc, press again to cancel this function when

it show “INT OFF”.

Repeat a track: Press RPT button (17) once to repeat your desired track. Press again

to repeat all.

Random playing: RDM Press button (16), all tracks will play randomly.

SELECTING DIRECTORY UP/DOWN: DIR + Press DIR-button (15) or button (14) to

select directory downward or upward. If the MP3 disc does not contain any directory,

there is no function of pressing button (15) or button (14).DIR- DIR +

Searching a track in MP3-CD/USB/card:

Use the keys for corresponding number or letter when you search a music ﬁ le:

- Search by track number:

1. Press button (6) once, LCD shows “NUM SCH” and “NUM AMS/SCH ***” press the

keys standing for corresponding numbers (refer to upper list).

2. Press knob (5) to start playing.SEL/VOL

- Search by letter:

1. Press button (6) twice, LCD shows “FILE SCH” and “AMS/SCH *- - - -” press the

keys standing for corresponding letters (refer to upper list).

2. Repeat this procedure until you ﬁ nish the ﬁ le name.

3. Press knob (5) to start playing.SEL/VOL

- Search by folder:

1. Press button (6) thrice, LCD shows “DIR SCH” then the total directories AMS/SCH

and available directories name.

2. Rotate the knob (5) to search your desired folder, press SEL/VOL SEL/VOL knob (5)

to enter the selected directories.

3. Rotate the knob (5) to select your desired track, press SEL/VOL SEL/VOL (5)

button to start playing.

Exit disc/ USB/SD card mode

1. Press (10) to eject the disc. If the disc is not taken out within 10 seconds, it will

be automatically reloaded.

2. To exit USB mode, disconnect your USB device from the unit, it will switch to tuner

mode automatically.

3. To exit card mode, take out your SD/MMC card from the unit, it will switch to tuner

mode automatically.

Note

* Do not use CDs with irregular shape (for example octagonal or heart-shaped).

* Notes: CD-Rs or CD-RWs playback capability of this player may vary depending on

quality media, CD-Burner, burning speed and application software.

* There are many USB devices or SD/MMC card on the market. We cannot guarantee

to support all different models. Please try another USB device or SD/MMC card if your

device is not supported.

* The unit might not support all the multimedia ﬁ les stored in SD/MMC card or USB

because it includes some special playback procedure which might not be compatible

with the procedure of this unit.

Precaution

- Clean the front panel with a soft cloth, or damp chamois leather. Never use solvents.

- Do not expose to rain or water; Handling the Detachable Front Panel:

- Do not drop or apply shock.

- Make sure that you keep your set away from high temperatures.

- The use of apparatus in moderate climates.

- Do not be exposed to dripping or splashing, and that no object ﬁ lled with liquids, such

as vases, shall be placed on the apparatus.

- No naked ﬂ ame sources such as lighted candles should be placed on the apparatus.

Cleaning the Connector

If the connector between the main unit and the front panel is dirty, may result in ab-

normal working condition. To avoid such problems, please detach the front panel, and

clean the connector with an alcohol swab. Gently clean and avoid damaging the con-

nector.

Notes:

For the sake of safety, always shut down the engine and take out the igni-

tion key before cleaning. Never keep your finger or any metal device on the

connector directly.

Replacing the Fuse

Make sure the amperage matches the speciﬁ ed value when replacing the fuses. If the

fuse is blown, check the power connection and replace with a new one. If the same

problem occurs, it would be subjected to the malfunction in-house. In such cases,

please consult the nearest service dealer.

Note:

Due to continuous product improvement, specifications and design are subject to

change without prior notice.

CAUTION! This set uses a laser beam. To prevent any accident due to this type of

beam, the set should only be opened by properly trained personnel. The unit conforms

to the international safety speciﬁ cations and to guide lines of the European community

and also complies with current standards concerning electrical safety and electromag-

netic compatibility EMC.

When reception is bad, the “ ” icon will blink.AF

Press and hold button (24) for 5 seconds, the unit will be under “REG ON” or “REG AF

OFF” mode:

REG ON: Should be selected to list the local broadcast of the current station, even if

there is a national broadcast of this station.

REG OFF: Should be selected to listen to the national broadcast of the current

station.

The exclamation point within the triangle is a warning sign alerting the user of

important instructions accompanying the product.

The lightening ﬂ ash with arrowhead symbol within the triangle is a warning

sign alerting the user of “dangerous voltage” inside the unit.

PTY SPEECH group PTY MUSIC group PTY off

MAINTENANCE

/VOL(press)

(1/PAU)

(2/INT)

(3/RPT)

(4/RDM)

(5/DIN -)

(6/DIN +)

7/MODE

KEY

0/DSP

(rotate)

AR-3045 IB MUSE 001 REV0 GB.indd2 2

AR-3045 IB MUSE 001 REV0 GB.indd2 2AR-3045 IB MUSE 001 REV0 GB.indd2 2 2011-2-28 15:58:41

2011-2-28 15:58:41

2011-2-28 15:58:412011-2-28 15:58:41

Specyfikacje produktu

Marka:	Muse
Kategoria:	Radia samochodowe
Model:	M-1015

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Muse M-1015, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Radia samochodowe Muse

Muse M-198 DAB Instrukcja

8 Października 2024

Muse M-715 DR Instrukcja

4 Października 2024

Muse M-095 Instrukcja

26 Września 2024

Muse M-199BT Instrukcja

13 Września 2024

Muse M-1010 Instrukcja

7 Września 2024

Muse M-718 DR Instrukcja

4 Września 2024

Muse M-1015MR Instrukcja

3 Września 2024

Muse M-1015 Instrukcja

2 Września 2024

Muse M-1230 BT Instrukcja

24 Sierpnia 2024

Muse M-092 MR Instrukcja

8 Sierpnia 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

JVC KD-R90BT Instrukcja

15 Października 2024

Kenwood KMM-X705 Instrukcja

15 Października 2024

Alpine CDM-7870R Instrukcja

14 Października 2024

Hyundai H-CMD2009 Instrukcja

14 Października 2024

Dual XC4100 Instrukcja

13 Października 2024

Audiovox VXE 3010 Instrukcja

13 Października 2024

MB Quart PAB 5400 Instrukcja

13 Października 2024

Hyundai H-CDM8023 Instrukcja

13 Października 2024

Caliber RCD110B Instrukcja

13 Października 2024

JVC KD-X30 Instrukcja

13 Października 2024