Instrukcja obsługi Mtx Audio TRP8

Mtx Audio Niesklasyfikowane TRP8

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mtx Audio TRP8 (24 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/24

TRP8

20cm (8’’) Powered Vented Enclosure, 360W Peak, 120W RMS CEA

mtxaudio.eu

facebook.com/MTXEurope

twitter.com/MTXEurope

Gain

Input

EBC

Remote

High Level

Input

6V - 0,2V

Prot.

PWR.

+12V GND

Ch.1 Ch.2

Power

REM

Owner’s Manual - MTX TRP8

Thank You !

Thank you for purchasing an MTX Audio High-End ampliﬁer. Proper installation matched with MTX speakers and subwoofers provide

superior sound and performance for endless hours of waking the neighbors, slammin’ your friends or ﬂat out stomping wanna-be

players. Congrats and enjoy the ultimate audio experience with MTX !

Speciﬁcations :

• Powered vented enclosure

• Mono block class-D ampliﬁer

• Subwoofer : 20cm (8”)

• Ampliﬁer Max Power : 360W

• Ampliﬁer RMS Power : 120W

• High and low level inputs

• EBC (External Bass Control) remote included

• Dimensions : 33x31x31cm

Power Terminal (+12V) : This is the main power input for the ampliﬁer and must be connected directly to the positive terminal of the

vehicles battery for proper operation. Use caution when installing (+12V) power cable in the vehicle. Avoid running this cable parallel

with RCA cables, antennas, or other sensitive equipment due to massive currents that can induce noise into the audio system. It is

also very important to have a tight, secure connection for maximum performance. MTX recommends using a minimum of 6mm2 full

copper power wire with the MTX TRP8.

Remote Terminal (REM) : The ampliﬁer can be turned on by applying 12 volts to this terminal. Typically this voltage is supplied by a wire

from the source unit marked “remote” or “power antenna”.

Ground Terminal (GND) : A proper ground is required for your ampliﬁer to operate at peak performance. A short ground cable the same

diameter as the power cable should be used to attach the ground terminal directly to the chassis of the vehicle. Always remove paint,

dirt or debris to expose bare metal where the ground will be attached.

Protection LED (Prot.) : When the amp is in thermal protection, the LED turns to red.

PowerOn LED (PWR.) : The LED illuminates red when the amp is switched on.

RCA Inputs (Input) : These RCA inputs are used with source units that have RCA or Line level outputs. (Source units need a minimum

level of 200mV output for proper operation of the ampliﬁer). MTX recommends only high quality RCA cables to decrease the possibility

of radiated noise entering the system.

Gain Control (Gain) : The gain control matches the input sensitivity of the ampliﬁer to the source unit being used.

The operating range varies from 200mv to 6V. Adjusting the gain:

1. Turn the gain control on the ampliﬁer all the way down (counter clockwise).

2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.

3. Adjust the gain control on the ampliﬁer until audible distortion occurs.

4. Adjust the gain control down until audible distortion disappears.

5. The ampliﬁer is now calibrated to the output of the source unit.

Speaker level inputs (High Level Input) : This input will allow the ampliﬁer to operate from source units with speaker-level outputs.

Output speaker leads from the source unit should be tied directly to the wire harness provided with the ampliﬁer.

Note : When speaker level inputs are used, a remote turn on wire must used to switch the ampliﬁer on and oﬀ.

Remote bass control port (EBC) : use this port to connect the optional MTX EBC. It alows you to control the output level siting at the

front of the car.

Control Panel on the Ampliﬁer :

Installation & Mounting :

MTX recommends your new MTX TRP8 to be installed by an Authorized MTX retailer. Any deviation from speciﬁed installation instruc-

tions can cause serious damage to the ampliﬁer, speakers and/or vehicles electrical system. Damage caused from improper installation

is NOT covered under warranty. Please verify all connections prior to turn on your system !

1. Disconnect the vehicle’s negative battery cable.

2. Determine the mounting place for your MTX TRP8. Keep in mind there should be suﬃcient air ﬂow for proper cooling.

3. Install a positive (+) power cable from the vehicle’s battery through the ﬁrewall using a grommet or ﬁrewall bushing to avoid cable

damage from sharp edges of the ﬁrewall. Run the cable through the interior of the vehicle and connect it to the ampliﬁer (+12V)

terminal (1). Do Not connect to the battery at this time.

Note : Use only proper gauge wire for both positive and negative connections.

4. Install a circuit breaker or fuse within 20cm of the battery. This eﬀectively lowers the risk of severe damage to you or your vehicle

in case of a short circuit or accident. Make sure the circuitbreaker is switched oﬀ or the fuse is taken out of the fuse holder untill all

connections are made. Now connect your positive power cable to the positive battery terminal of the battery.

5. Grounding - Locate a proper ground point on the vehicle’s chassis and remove all paint, dirt or debris to reveal a bare metal surface.

Attach the ground wire to that contact point. Connect the opposite end of the ground wire to the (GND) terminal on the ampliﬁer (3).

6. Connect a remote turn-on wire from the source unit to ampliﬁer remote terminal (2). If the source unit does not have a dedicated

Remote Turn-on lead, you may connect to the source unit’s Power Antenna lead.

7. Connecting signal cables to the ampliﬁer : There are two ways to supply the signal to your MTX TRP8.

• To get maximum performance, we suggest connecting a high quality RCA to the corresponding outputs at the source unit and inputs

of the ampliﬁer.

• If a source unit is being used without RCA outputs, use the included high-level ampliﬁer’s speaker terminals (8) using the right

gauge speaker wire.

8. Double check all previous installation steps, in particular, wiring and component connections. Once veriﬁed, reconnect the vehicle’s

negative battery cable, turn the circuit breaker on or place the fuse in the fuse holder.

Note : Gain Levels on the ampliﬁer should be turned all the way down (counter clockwise) before proceeding with adjustments.

How To Stay Tuned :

https://www.facebook.com/MTXEurope

https://twitter.com/MTXEurope

http://www.mtxaudio.eu

Specyfikacje produktu

Marka:	Mtx Audio
Kategoria:	Niesklasyfikowane
Model:	TRP8

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mtx Audio TRP8, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Mtx Audio

Mtx Audio TRP8 Instrukcja

22 Września 2024

Mtx Audio iWa250 Instrukcja

17 Września 2024

Mtx Audio Terminator TNA251 Instrukcja

16 Września 2024

Mtx Audio RTP8x2 Instrukcja

16 Września 2024

Mtx Audio RTF10P Instrukcja

13 Września 2024

Mtx Audio Terminator TN500-1D Instrukcja

12 Września 2024

Mtx Audio iX3 Instrukcja

11 Września 2024

Mtx Audio TRT8P Instrukcja

11 Września 2024

Mtx Audio RTU8P Instrukcja

10 Września 2024

Mtx Audio X3-17-Thunder5 Instrukcja

10 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024