Instrukcja obsługi MSR Whisperlite Universal

MSR Rożen Whisperlite Universal

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla MSR Whisperlite Universal (2 stron) w kategorii Rożen. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Pump

Body

Control

Valve

Assembly

Canister Fuel

Adapter

Canister Fuel

Adapter

Canister

Stand

Jet and

Cable Tool

Liquid Fuel

Adapter

Liquid Fuel

Adapter

Flame

Adjuster

Fuel Line

Retainer

Nut

Swivel

O- Rings

Fuel Tube

O- ring

Check

Valve

Fuel Pump

Groove

Pump

Seal

Plunger

Fuel Tube

Bushing

Pump

Cup

Plunger

Bushing

Plunger

Bushing

Tabs

Pot Supports/

Legs

Windscreen

Elbow

Burner

Head

Mixer

Tube

UK Jet

UG Jet

UC Jet

Shaker

Needle

Generator

Tube

Heat

Reflector

Catch

Arm

Priming

Cup

Priming

Wick

Rim

Detent

WARNING

WARNING WARNING

WARNING

Do not use this stove: (1) before reading and fully understanding this Instruction Manual; (2) if you are not prepared or comfortable attending to a burning and/or hot stove at all times; (3) if you observe

leaking fuel; or (4) if you observe any condition with the stove system or in the surrounding environment that would make operation of an open flamed device dangerous. Failure to follow these directions

can cause an unsafe situation leading to fire, burns, severe injury or death.

KNOW YOUR MSR ® WHISPERLITE ™ UNIVERSAL STOVE

Please familiarize yourself with the parts of your WhisperLite Universal stove and the fol-

lowing instructions before its use. Because this stove can accommodate different fuels, you

may need to exchange the preinstalled UC Jet and the Canister Fuel Adapter before using

this stove.

CONFIGURING STOVE FOR DIFFERENT FUELS

CHANGING THE JET

1. Fold Pot Supports/Legs.

2. Unscrew Priming Cup and remove Wick.

3. Remove Fuel Line from stove.

4. Loosen current Jet with Jet and Cable Tool.

Carefully unscrew Jet to avoid losing Shaker Needle inside the Elbow.

IMPORTANT: Do not bend Generator Tube while removing Jet.

5. Set new Jet carefully over the Shaker Needle and screw into place.

Gently tighten the Jet with Jet and Cable Tool.

6. Hold folded Pot Supports/Legs together and reinstall Fuel Line.

Replace Wick and rescrew Priming Cup to reassemble stove.

CHANGING THE FUEL ADAPTER

1. Loosen Retainer Nut on current Fuel Adapter with Jet and Cable Tool.

2. Unthread Retainer Nut and disconnect Fuel Adapter from Fuel Line.

3. Insert end of Fuel Line into new Fuel Adapter.

4. Gently tighten Retainer Nut with Jet and Cable Tool.

STOVE PREPARATION

FUEL BOTTLE PREPARATION

CONNECT STOVE CONNECT STOVE

TURN STOVE ON TURN STOVE ON

USE STOVE TO COOK USE STOVE TO COOK

TURN STOVE OFF TURN STOVE OFF

SET UP STOVE

The WhisperLite™ Universal stove

can be easily configured to burn

white gas and unleaded gas, kero-

sene, and canister fuels. Before stove

use, select the fuel and install the

appropriate Jet and Fuel Adapter.

(See )Fuel Information.

Unscrew

Priming Cup

Remove

Jet

Loosen

Retainer Nut

Tighten

Retainer Nut

Insert Fuel

Line

Use MSR® fuel bottles only. Non-MSR fuel bottles may leak fuel creating an unsafe situation leading to fire, burns, severe injury or death. Keep children far away from stove and fuel—Cascade

Designs, Inc. recommends no less than 10 feet (3+ meters). Never leave a burning or hot stove unattended. An unattended stove can lead to fire and/or a situation where children, pets, or the

unwary can be burned, injured, or killed. Use extreme caution when using stove in temperatures below freezing. In freezing temperatures O-rings can stiffen and leak fuel. Always check for fuel leaks

before and after pressurizing bottle, priming, and during and after lighting stove. Use of a leaking stove can cause fire, burns, severe injury or death.

Ensure that the WhisperLite™ Universal stove is configured with the correct Jet and Fuel Adapter. (See Stove

Preparation.) If using a liquid fuel, prepare the Fuel Bottle before using the stove. If using a canister fuel, skip this

panel and go now to Step 1, Set Up Stove.

PREPARING FUEL BOTTLE FOR LIQUID FUELS

1. Fill Fuel Bottle to fill line only.

Air space is necessary for fuel expansion.

2. Insert Pump into Fuel Bottle and firmly tighten.

3. Check Fuel Bottle for leaks pressurizing the bottle.before

4. Close the Control Valve, then stroke Plunger (20-30 strokes).

Pump until firm resistance is felt.

Less fuel requires more strokes or pressure.

1. Close Control Valve/Flame Adjuster

Valve.

2. Unfold the 3 Pot Supports/Legs.

Rotate Pot Supports/Legs fully open.

3. Place stove on the center of the Heat

Reflector.

Keep combustibles at least 4 feet (1.2 meters) away from the top and sides of a burning stove or a stove that you are in the process of lighting. Keep flammable liquids and vapors at least 25

feet (7.6 meters) away from the top and sides of a burning stove or a stove that you are in the process of lighting. This stove can ignite combustible materials, flammable liquids and vapors creat-

ing a situation where fire, burns, severe injury or death can result. This stove is designed for the outside (i.e., not within enclosure spaces of any kind, e.g., tents) and for the boiling of water or

cooking of food only—never use it for any other purpose. Use of stove within any enclosure or for a purpose other than boiling water or cooking food can cause fire, burns, severe injury or death.

Never overtighten fuel canister to stove. Overtightening can damage stove or canister and cause fuel to leak. Leaking fuel can cause fire, burns, severe injury or death. Use extreme caution when using stove

in temperatures below freeing. In freezing temperatures O-rings can stiffen and leak fuel. Always check for fuel leaks before and after lighting stove. Use of a leaking stove can cause fire, burns, severe

injury or death. Keep children far away from stove and fuel–Cascade Designs, Inc. recommends no less than 10 feet (3+ meters). Never leave a burning or hot stove unattended. An unattended stove can

lead to fire or a situation where children, pets, or the unwary can be burned, injured, or killed. The canister must be constructed and marked in accordance with the CAN/CSA 339.

1. Lubricate the entire brass end of Liquid Fuel Adapter with saliva or oil.

2. Completely insert brass end of Liquid Fuel Adapter into Pump.

Place Fuel Bottle on its side so Control Valve points up.

3. Secure Catch Arm on Fuel Pump Groove.

Keep Fuel Line straight for safety.

Keep Fuel Bottle as far away from stove as possible.

Use UG Jet and Liquid Fuel Adapter for white gas and unleaded auto gas.

Use UK Jet and Liquid Fuel Adapter for kerosene. (See Stove Preparation.)

Before every use, look for fuel on the fuel bottle, pump, fuel line, burner, and on the area beneath and

around stove. Do not light stove if you see or smell fuel. (See Troubleshooting.) Use of stove where

fuel has leaked or is leaking can cause fuel to ignite causing fire, burns, severe injury or death. Never

disconnect the fuel line, pump, or fuel bottle when stove is burning, hot, or near any open flame. Never

disconnect fuel line, pump, or fuel bottle when control valve is in an open (i.e., fuel flowing) position.

Disconnecting fuel line, pump, or fuel bottle when stove is burning, hot, or near any open flame, or

disconnecting fuel line, pump, or fuel bottle when control valve is in an open (i.e., fuel flowing) position

can lead to spilled fuel that can ignite and cause fire, burns, severe injury or death.

1. Unfold Flame Adjuster.

2. Close Flame Adjuster Valve on Canister Fuel Adapter.

3. Screw Fuel Canister onto Canister Fuel Adapter.

Use UC Jet and Canister Fuel Adapter for all canister fuels. (See Stove Preparation.)

1. Release only ½ spoonful of fuel.

Open Control Valve (3/4 turn) and let fuel flow through the Jet.

Close Control Valve.

Look for fuel in Priming Cup and on Wick.

2. Light fuel in Priming Cup.

A brief soccer ball-sized flame is normal.

3. Wait for preheat flame to reduce in size (approximately 2 minutes).

If flame goes out, wait 5 minutes for stove to cool before relighting.

4. Open Control Valve (1/2 turn) and wait for steady blue flame.

5. Slowly open Control Valve.

Never place your head or body above the stove while priming, lighting, or cooking. Because stove maintains an open flame, placement of head or body above stove is an unsafe practice that can cause

fire, burns, severe injury or death. Never use excess fuel to preheat stove. Use of excess fuel for priming can lead to leaking or spilled fuel that can cause fire, burns, severe injury or death. Never relight

a heated stove. Always let an extinguished stove cool for at least 5 minutes before relighting. Relighting a heated stove can cause large flames that can cause fire, burns, severe injury or death. Never

move a burning or hot stove. Always extinguish stove and cool for at least 5 minutes before moving. Moving a burning or hot stove can cause fire, burns, severe injury or death.

VAPOR FEED MODE (most conditions, best simmering)

1. Hold a lit match or lighter over the edge of Burner Head.

2. Open Flame Adjuster Valve (3/4 turn) to release and ignite fuel.

3. Turn Flame Adjuster Valve to produce and maintain steady

blue flame.

Never place your head or body above the stove while priming, lighting, or cooking. Because stove maintains an open flame, placement of head or body above stove is an unsafe practice that can cause fire, burns, severe

injury or death. Never relight a heated stove. Always let an extinguished stove cool for at least 5 minutes before relighting. Relighting a heated stove can produce large flames that can cause fire, burns, severe injury or

death. Never move a burning or hot stove. Always extinguish stove and cool for at least 5 minutes before moving. Moving a burning or hot stove can cause fire, burns, severe injury or death.

LIQUID FEED MODE (very cold conditions or higher output/faster boiling)

1. Attach Canister Stand onto top of Canister Fuel Adapter.

2. Hold a lit match or lighter over the edge of the Burner Head.

3. Open Flame Adjuster Valve (3/4 turn) to release and ignite fuel.

Allow fuel to burn for 30 seconds to sufficiently preheat stove.

4. Invert Fuel Canister, using Canister Stand to support it.

5. Turn Flame Adjuster Valve to produce and maintain steady blue flame.

IMPORTANT: ALWAYS START STOVE WITH FUEL CANISTER IN UPRIGHT POSITION TO PREVENT A LARGE FLARE-UP.

1. Set up Windscreen.

Fold the ends of Windscreen together.

Leave a 1-inch (2.5-cm) gap between Windscreen and pot for optimal

performance.

Ensure that combustion flow and ventilation air are free of any obstruction.

Use Windscreen to improve performance in all conditions.

2. Add appropriate food or liquid to cookware.

3. Place cookware onto center of stove.

4. Maintain Fuel Bottle pressure.

Add approximately 10 strokes every 10 minutes to maintain

performance.

Hold Fuel Bottle firmly while pumping.

Keep fuel bottle away from the stove burner and other heat sources. Position connected fuel bottle so that it is as far away from the burner as possible. Use of bottle near burner or other heat sources

can result in the fuel bottle exploding and causing fire, burns, severe injury or death. Never place Windscreen around fuel bottle. Never use cookware with a diameter greater than 10 inches (25

centimeters). Never place and operate two or more stoves together. Never operate stove with empty or dry cookware. Never use non-MSR ® reflectors or diffusers. Use of stove in any of the preceding

manners can result in the fuel bottle exploding and causing fire, burns, severe injury or death. Never use cookware of any size that is ill-suited or inappropriate for use with stove or stove pot supports

(e.g., cookware with a convex or concave bottom, some enameled cookware, etc.). Use of stove with ill-suited and/or inappropriate cookware can result in cookware and/or stove instability and a

situation where hot cookware and/or cookware contents can spill and cause fire, burns, severe injury or death. Cascade Designs, Inc. warrants the use of appropriately sized MSR ® brand cookware

only—use of cookware other than MSR ® brand cookware will be at user’s own risk and discretion.

1. Set up Windscreen.

Fold the ends of Windscreen together.

Leave a 1-inch (2.5-cm) gap between

Windscreen and pot for optimal perfor-

mance.

Ensure that combustion flow and ventilation

air are free of any obstruction.

Use Windscreen to improve performance in

all conditions.

2. Add appropriate food or liquid to cookware.

3. Place cookware onto the center of stove.

Never use cookware with a diameter greater than 10 inches (25 centimeters). Never place and operate two or more stoves together. Never operate stove with empty or dry cookware. Never use non-MSR ®

reflectors or diffusers. Use of stove in any of the preceding manners can result in the fuel canister exploding and causing fire, burns, severe injury or death. Never use cookware of any size that is ill-suited

or inappropriate for use with stove or stove pot supports (e.g., cookware with a convex or concave bottom, some enameled cookware, etc.). Use of stove with ill-suited and/or inappropriate cookware can

result in cookware and/or stove instability and a situation where hot cookware and/or cookware contents can spill and cause fire, burns, severe injury or death. Cascade Designs, Inc. warrants the use of

appropriately sized MSR ® brand cookware only—use of cookware other than MSR ® brand cookware will be at user’s own risk and discretion.

1. Close the Control Valve.

Residual flame will continue to burn with a small flame.

2. After flames are out, wait 5 minutes for stove to cool.

3. Unlock Catch Arm and remove Fuel Line from Pump.

4. Depressurize Fuel Bottle and repack stove.

Hold Fuel Bottle upright, away from your face and

any sources of heat or ignition.

Slowly unscrew pump to depressurize Fuel Bottle.

NOTICE: To transport the Fuel Bottle, the Pump may be left

inside a depressurized Fuel Bottle. The Pump can also be

removed and replaced with the Fuel Bottle Cap.

Always store fuel bottle with cap securely tightened where it cannot be accessed by children. Storage of fuel bottle with loose cap and easy accessibility by children can result in a child opening the

fuel bottle and accessing bottle contents. Exposure to or ingestion of bottle contents can cause poisoning, severe injury, or death. Always store fuel bottle in a well-ventilated location away from any

possible heat or ignition source, such as water heaters, stoves, pilot lights, or furnaces. Storing bottle near any heat or ignition source can result in the fuel bottle exploding and causing fire, burns,

severe injury or death.

1. Place the Fuel Canister in the upright position if inverted.

2. Close the Flame Adjuster Valve.

Residual flame will continue to burn with a small flame.

3. After flames are out, wait 5 minutes for stove to cool.

Remove Canister Stand if attached.

Fold Flame Adjuster Valve.

4. Ensure that burners are extinguished.

Fold Pot Supports/Legs.

5. Move stove assembly away from any ignition sources and unscrew

Fuel Canister.

A small amount of gas may escape when unscrewing canister.

If canister is completely empty of fuel, follow proper disposal

requirements in your local area.

Always disconnect stove from canister before storing it. Failure to disconnect stove from canister before storing may allow fuel to leak and cause fire, burns, severe injury or death. Always store fuel canisters

in a well-ventilated location away from any possible heat or ignition source, such as water heaters, stoves, pilot lights, or furnaces, or where temperatures exceed 120 F (49 C). Storing fuel canisters near

any heat or ignition source or where temperatures exceed 120 F (49 C) can result in the canister exploding and causing fire, burns, severe injury or death.

Stroke

FULL

20-3 0 Stroke s

1/2 F ULL

30-4 0 Stroke s

FILL

LINE

AIR

FUEL

4-ft. (1.2-m) MIN.

DISTANCE from

COMBUSTIBLE

MATERIALS

25-ft. (7.6-m) MIN.

DISTANCE from

FLAMMABLE LIQUIDS/

VAPORS

OPERATOR POSITION

OPEN OPEN

OPEN WAIT

30 SEC.

BELOW EYE

LEVEL

WAIT!

5 MIN.

3/4 TURN

3/4 TURN 3/4 TURN

1/2 TURN SLOWLY

WAIT!

STEADY

BLUE FLAME

1/2-in.

(1.3-cm)

1/2-in.

(1.3-cm)

COOKWARE

10-in. (25-cm) DIA.

MAX

10 Strokes

10 MIN.

2 MIN.

COOKWARE

10-in. (25-cm) DIA.

MAX.

COOKWARE

6-in. (15-cm) HT. MAX.

10-lb. (4.5-kg) WT. MAX.

COOKWARE

6-in. (15-cm) HT. MAX.

10-lb. (4.5-kg) WT. MAX.

UG Jet

UK Jet

WHITE GAS AND UNLEADED AUTO GAS

KEROSENE

CANISTER FUELS

UC Jet

(preinstalled)

DANGER

FOR YOUR SAFETY

DAN

LIMITED WARRANTY/LIMITATIONS OF REMEDIES AND LIABILITY

USA and Canada

CARBON MONOXIDE

HAZARD

This stove produces car-

bon monoxide, which

has no odor. Using it in

an enclosed space can

kill you. Never use this

stove in an enclosed

space such as a camper,

tent, car, or home.

our O-rings before every trip.

he Annual Maintenance Kit or the

IMPORTANT

Read and understand this entire manual carefully

before assembling or using this stove. Keep this

manual for future reference. If you do not understand

this manual or have any questions, please call Cascade

Designs, Inc. at 1-800-531-9531.

Limited Warranty. Cascade Designs, Inc. (“Cascade”), to the original

owner (“Owner”), under intended use and maintenance, warrants

the enclosed product (“Product”) to be free from defects in materials

and workmanship for the life of the Product. No warranty against defects

in materials and workmanship will apply if Product is (i) altered in any way, (ii)

used for purposes inconsistent with Product’s intended purpose or design, or (iii)

improperly maintained. Warranty will furthermore be voided where Owner/user (i)

failed to follow Product instructions or warnings or (ii) subjected Product to misuse,

abuse, or neglect.

During the warranty period, original Product parts determined by Cascade to be

defective in materials or workmanship will be repaired or replaced as Owner’s sole

remedy. Cascade reserves the right to replace any discontinued product with a new

product of comparable value and function. A returned product deemed irreparable

becomes the property of Cascade and will not be returned.

EXCLUDING THE LIMITED WARRANTY PROVIDED ABOVE, CASCADE, ITS

AFFILIATES AND THEIR SUPPLIERS, TO THE MAXIMUM EXTENT PERMITTED BY

LAW, MAKE NO WARRANTIES, EXPRESSED OR IMPLIED, AND DISCLAIM ALL

WARRANTIES, DUTIES AND CONDITIONS, WHETHER EXPRESSED, IMPLIED

OR STATUTORY WITH RESPECT TO THE PRODUCT, INCLUDING WITHOUT

LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, AGAINST LATENT

DEFECTS, FITNESS FOR A PARTICULAR PURPOSE, OR CORRESPONDENCE TO

DESCRIPTION.

Warranty Service. To obtain service under this warranty, the warranty-

eligible Product must be presented to a Cascade authorized dealer. In the

United States and Canada, warranty service may also be obtained by calling

1-800-531-9531 [M-F, 8:00-4:30, PDT].

Owner is responsible for all costs associated with returning Product to Cascade for

service. Where at its sole discretion Cascade deems Product eligible for warranty

repair or replacement, Cascade will pay the shipping and handling associated

with returning repaired or replaced Product to Owner. In instances where Cascade

deems a returned product ineligible for warranty service, Cascade will, if possible,

repair product for a reasonable fee that includes return shipping and handling. For

warranty return service details, please go to www.msrgear.com.

Limitation of Remedies Should a court of competent jurisdiction find the limited .

warranty set forth above breached, Cascade’s only obligation will be, at its option,

either to repair or replace Product. Should the aforementioned remedy fail of

its essential purpose, Cascade will, in exchange for return of Product, refund to

Owner the Product’s original purchase price. THE FOREGOING REMEDY IS THE

SOLE AND EXCLUSIVE REMEDY OF THE PURCHASER AGAINST CASCADE, ITS

AFFILIATES AND THEIR SUPPLIERS, REGARDLESS OF LEGAL THEORY.

Limitation of Liability. Cascade’s, its affiliates’ and their suppliers’ maximum liability

is limited to incidental damages not to exceed the original purchase price of the

Product. CASCADE, ITS AFFILIATES AND THEIR SUPPLIERS HEREBY DISCLAIM AND

EXCLUDE ANY LIABILITY FOR ANY CONSEQUENTIAL OR OTHER DAMAGES

RESULTING FROM ANY REASON WHATSOEVER. THIS EXCLUSION AND

LIMITATION APPLIES TO ALL LEGAL THEORIES UNDER WHICH DAMAGES MAY

BE SOUGHT AND WILL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL

PURPOSE.

This limited warranty gives Owner specific legal rights; Owner may have additional

rights, which may vary state to state.

Always completely follow safety, use, operation, and maintenance instructions for

this or any other Cascade product.

European Union customer statutory rights are not affected.

CARBON MONOXI

EXPLOSION HA

There are serious hazards associa

and fuel. Accidental fire, explosion

death, serious burns, and property

sible for your own safety and the

group. Please use good judgment.

This stove is for OUTDOOR USE O

in a tent, vestible, car, house, or in

This stove consumes oxygen and pr

gas, which is poisonous and has no

ily ignite nearby combustible materi

or vapors. If you use this stove in a

be killed or seriously burned.

Keep stove and fuel bottle or fuel

heat sources. Never use cookware o

a diameter larger than 10 inches (2

cookware can overheat the fuel bo

expose the fuel bottle or fuel can

explode and you can be killed or s

Never let children use this stove. K

feet (3+ meters) away from the stov

supervise them at all times.

READ, UNDERSTAND, AND FOLLO

warnings in this manual before us

follow warnings and instructions ca

burns or other injury, and property

Unscrew

Retainer Nut

move Swivel

O-Rings

h can occur.

STOVE MAINTENANCE TROUBLESHOOTING

FUEL INFORMATION

Remove

Cable

Scour Fuel Line

20 X

5-in. (13-cm)

Strokes

5. Remove Shaker Needle and use it to clear Jet Orifice from top or bottom.

NOTE: To exchange Jets, place Shaker Needle in new Jet and reassemble stove.

6. Scour Fuel Line.

Unscrew Fuel Adapter from Fuel Line.

Remove Cable from Fuel Line with Jet and Cable Tool. Stubborn cables can be

loosened with a common lubricant (WD-40™, Pump Cup Oil, etc.).

Fully reinsert Cable into Fuel Line.

Move Cable in and out with 5-inch (13-centimeter) strokes approximately

20 times.

Wipe Cable clean.

7. Flush Fuel Line.

Remove Cable.

Connect Liquid Fuel Adapter to Fuel Line and install into Pump and Fuel Bottle.

Secure Catch Arm on Fuel Pump Groove.

Pressurize Fuel Bottle with 15 strokes.

Fully open Control Valve to flush 4 spoonfuls of fuel through Fuel Line into an

appropriate container. (Jet uninstalled.)

WARNING: Keep away from ignition sources.

Close Control Valve and remove Fuel Line.

Safely dispose fuel when flushing is complete.

8. Reassemble stove.

If stove performance is still impaired, repeat Cleaning the Jet and Fuel Line steps.

CLEARING THE JET WITH THE SHAKER NEEDLE

1. Close Pump Control Valve and wait 5 minutes for stove to cool.

2. Shake stove up and down.

Shaker Needle inside Jet should rattle.

3. Preheat and run stove.

If performance does not improve, perform Cleaning the Jet and Fuel Line steps.

CLEANING THE JET AND FUEL LINE

1. Fold Pot Supports/Legs to packed position.

2. Unscrew Priming Cup and remove Wick.

3. Hold folded Pot Supports/Legs together.

Remove Fuel Line from Mixer Tube.

4. Unscrew Jet with Jet and Cable Tool.

IMPORTANT: Do not bend Generator Tube while loosening Jet.

Deposits in the Jet and Fuel Line reduce fuel flow and impair stove performance. Minor deposits in the Jet can be cleared with

the Shaker Needle. Major deposits may require more extensive cleaning of the Jet and Fuel Line. At a minimum, perform the fol-

lowing maintenance annually or every time you perform the Pump Maintenance.

Shake the

Stove

Remove

Jet

Clear Jet

Orifice

Unscrew

Priming Cup

The WhisperLite™ Universal stove can burn a variety of fuels by exchanging the

Jet and Fuel Adapter.

1. The UG Jet and Liquid Fuel Adaptor are used for White Gas and Unleaded

Auto Gas.

2. The UK Jet and Liquid Fuel Adaptor are for Kerosene.

3. The UC Jet and Canister Fuel Adaptor are used for canister fuels.

Both the UK and UG Jets and the Liquid Fuel Adapter are included in the parts

kit with your stove.

To exchange the Jet or Fuel Adapter, see Stove Preparation.

Use MSR® SuperFuel™ (White Gas) or MSR IsoPro (canister fuel) for optimal

performance. It is the highest quality fuel available for your stove. Do not use

leaded fuels. Fuels other than MSR SuperFuel white gas or MSR IsoPro can lead

to rapid stove clogging and require more frequent Jet and Fuel Line cleanings.

Also, the use of Unleaded Auto Gas may shorten stove lifespan. Use the fuels

chart to help you find your fuel when traveling internationally.

Use of stove with non-MSR fuel products is not recommended.

Visit www.msrgear.com for more information on international fuel names and

safe stove transportation.

USA/UK/CANADA GERMANY/

SWITZERLAND JAPAN FRANCE NETHERLANDS SPAIN

LIQUID FUEL

White Gas,

Naphtha Kocherbenzin,

Reinbenzin White Gas Pétrole à brûler,

Essence C Wasbenzine Bencina

blanca

Kerosene Petroleum Toh-yu Kérosène Petroleum

Lampolie Parafina

Unleaded

Auto Gas Autobenzin Gasoline Essence sans

plomb Benzine Gasolina sin

plomo

CANISTER FUEL FLÜSSIGBRENNSTOFF

KARTUSCHE

Kyanisutā

Ka CARTOUCHE DE

GAZ TANK ONDER

DRUK BOMBONA

DE GAS

Butane,

Isobutane,

Propane

Butan,

Isobutan,

Propan

Butan,

Isobutan,

Puropan

Butane,

IsoButane,

Propane

Butaan,

Isobutaan,

Propaan

Butano,

Isobutano,

Propano

Problem

Leaking Fuel Cause Solution

At Pump and Fuel Bottle

Connection Damaged or missing Pump

Seal Replace Pump Seal

At Pump and Fuel Line

Connection Damaged or missing Fuel

Tube O-ring Replace Fuel Tube O-ring

At Control Valve Stem Damaged or missing

Control Valve O-ring Replace Control Valve O-ring

In Pump Plunger Chamber Obstructed Check Valve Clean Check Valve Cavity

Poor Performance

(LIQUID FUEL) Cause Solution

Pump not pressurizing Fuel

Bottle Loose or poorly seated Pump

Damaged Pump Cup

Tighten or rescrew Pump

on Fuel Bottle

Replace Pump Cup

Plunger hard to pump Dry Pump Cup Lubricate Pump Cup

Diminished flames Low Fuel Bottle pressure Pump the Plunger

Poor Performance

(CANISTER FUEL) Cause Solution

Diminished flames Low fuel

Cold canister

Replace canister

Swap canister

Stove does not light Cold canister

Windy conditions

Empty canister*

Swap canister

Use Wind Screen

Replace canister

*To check if canister is empty, remove stove and gently shake canister. If a splashing sound is

heard, canister still contains fuel.

Poor Performance

(ALL FUELS) Cause Solution

Erratic flames, loud burning

noise Incorrect Jet/Fuel Adapter

configuration Check Jet and Adapter - install

correct configuration for fuel

in use

Erratic yellow flames Improper preheating Repeat Step 3

Slow boil times Clogged Jet or Fuel Line Clear Jet and clean Fuel Line

Diminished flames at altitude Insufficient airflow Open Windscreen slightly

WIVEL O-RINGS

m Fuel Line.

e if damaged.

fety Pin.

mp Cup Oil or any mineral-based oil.

el Adaptor.

If you smell gas

1. Do not attempt to light stove.

2. Extinguish any open flame.

3. Disconnect from fuel canister.

Do not store or use gasoline or other

liquids with flammable vapors in the

vicinity of this or any other stove.

Specyfikacje produktu

Marka:	MSR
Kategoria:	Rożen
Model:	Whisperlite Universal

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z MSR Whisperlite Universal, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Rożen MSR

MSR Wind Pro II Instrukcja

14 Września 2024

MSR DragonFly Instrukcja

13 Września 2024

MSR Whisperlite International Instrukcja

13 Września 2024

MSR Whisperlite Universal Instrukcja

12 Września 2024

MSR XGK-EX Instrukcja

11 Września 2024

MSR Windburner Instrukcja

11 Września 2024

MSR SuperFly Instrukcja

11 Września 2024

MSR PocketRocket Deluxe Instrukcja

11 Września 2024

MSR WhisperLit Universal Instrukcja

11 Września 2024

MSR PocketRocket 2 Instrukcja

11 Września 2024

Instrukcje Rożen

Najnowsze instrukcje dla Rożen

Barbecook Siesta 210 Instrukcja

12 Października 2024

Tefal CB2231 Easy Grill Comfort Instrukcja

10 Października 2024

Roesle MAGNUM PRO G3 Instrukcja

9 Października 2024

Roesle No.1 F60 AIR Instrukcja

9 Października 2024

Roesle Smoker No.1 F50-S Instrukcja

9 Października 2024

Roesle Videro G4 Instrukcja

9 Października 2024

Grill Guru Classic Large Instrukcja

9 Października 2024

Euro Appliances EAL1200RBQBL Instrukcja

9 Października 2024

Euro Appliances EAL900RBQBL Instrukcja

9 Października 2024

XO GPOWER60K Instrukcja

8 Października 2024