Instrukcja obsługi Moxa INJ-24

Moxa wzmacniacz wifi INJ-24

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Moxa INJ-24 (8 stron) w kategorii wzmacniacz wifi. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

 11 . A20 Moxa Inc ll rights reserved.

P/N: 1802000240011

Moxa PoE Injector

INJ- 24 Series

Hardware Installation Guide

Second Edition, March 2011

- - 2

Overview

The that Moxa PoE Injector INJ- 24 Series is a 1- port PoE injector

delivers both data and electrical power to Ethernet-enabled devices using

a single Ethernet cable. The INJ- 24 can supply up to 30 watts of power

through the port, and can power IEEE 802.3af Ethernet /at compliant

powered devices (PD), such as wireless access points or IP cameras,

eliminating the need for additional wiring. The INJ- G24 supports igabit

communication, which is vital for high speed- and low-latency applications.

The INJ-24 also offers a wide operating temperature range of -40 to 75°C,

and is designed to withstand a high degree of vibration and shock. A

rugged hardware design makes the INJ-24 perfect for ensuring that your

Ethernet equipment can operate in critical industrial environments, such

as in hazardous locations, and complies with FCC and CE standards.

Wiring Requirements

WARNING

Do not disconnec

t modules or wires unless the power supply has

been switched oﬀ or the area is known to be non-

hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

Safety Extra-Low Volta

ge. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

Safety Extra-Low Voltages (SELV) in compliance with IEC

60950 1.-1/EN 60950-

WARNING

The power for this product is

intended to be supplied by a Listed

Power Unit, with output marked LPS, and rated to deliver 24 DC

at a maximum of 1.3 A.

WARNING

This unit is a built-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply with ﬁre enclosure regulation IEC 60950- -1/EN60950 1

(or similar regulation).

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa PoE injector. Calculate the maximum possible

current in each power wire and common wire. Observe all

electrical codes dictating the maximum current allowable for each

wire size. If the current goes above the maximum ratings, the

wiring could overheat, causing serious damage to your

equipment.

- - 3

You should also pay attention to the following items:

• Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

• NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with diﬀerent

signal characteristics should be routed separately.

• You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

• Keep input wiring and output wiring separated.

• It is strongly advised that you label wiring to all devices in the system

when necessary.

Package Checklist

The Moxa - Series INJ 24 is shipped with the following items. If any of

these items is missing or damaged, contact a Moxa customer service

representative for assistance.

• Moxa PoE Injector INJ- 24

• Hardware Installation Guide

• Moxa Product Warranty Statement

Features

High Performance Network Switching Technology

• 10/100/1000BaseT(X)

• Provides up to 30 watts per PoE port

• Active circuit protection

• Auto disconnection for over voltage or under voltage

• Power consumption detection and classiﬁcation

• Industrial- grade reliability

Rugged Design

• Operating temperature range from 0 to 60°C, or extended operating

temperature from - 40 to 75°C for “T” models

• IP30, rugged high- strength case

• DIN-Rail or panel mounting ability

Specyfikacje produktu

Marka:	Moxa
Kategoria:	wzmacniacz wifi
Model:	INJ-24
Kolor produktu:	Czarny
Napięcie wejściowe AC:	12-48 V
Wysokość produktu:	100 mm
Szerokość produktu:	24.9 mm
Głębokość produktu:	86.2 mm
Waga produktu:	115 g
Certyfikaty:	EN 61000-4-2 (ESD) Level 3, EN 61000-4-3 (RS) Level 3, EN 61000-4-4 (EFT) Level 3, EN 61000-4-5 (Surge) Level 3, EN 61000-4-6 (CS) Level 3, FCC Part 15 Subpart B Class A, EN 55022 Class A
Standardy komunikacyjne:	IEEE 802.3, IEEE 802.3ad, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ilość portów Ethernet LAN (RJ-45):	2
Obsługa PoE:	Tak
Zakres temperatur (eksploatacja):	-40 - 75 °C
Zakres wilgotności względnej:	5 - 95 %
Wi-Fi:	Nie
Zakres temperatur (przechowywanie):	-40 - 85 °C
Model:	Wzmacniacz sieciowy
Technologia okablowania:	10/100/1000Base-T(X)
Prąd wejściowy:	1.3 A
Maksymalny dystans transferu:	- m
MTBF (Średni okres międzyawaryjny):	2525278 h