Instrukcja obsługi Mount-It! MI-7285


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mount-It! MI-7285 (7 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/7
ON-WALL TV CABLE
CONCEALER KIT
MI-7285
Scan this QR code for
product information, videos,
and assembly assistance.
2
PACKAGE CONTENTS
WARNING
1. Due to the extremely sticky nature of the tape, please
plan your installation well in advance of installation to
avoid removing and reinstalling the cable channel. If
it is necessary to unplug the channel, try to soften the
bottom of the raceway by heating it with a Hair Dryer
(not too high a temperature is recommended) and then
gently peel it off.
2. The channels can be cut to a shorter length if needed,
please take all proper safety precautions when cutting
and beware of possible sharp edges left over.
3. It is not recommended that the channel be mounted
on an uneven wall, if you do need to mount on a
rough wall, use screw mounting rather than double
sided tape.
4. Do not use this product to route uninsulated, exposed,
or damaged wiring.
5. This product is intended to route and conceal cables for
decorative purposes, it may not be used as a structural
cable conduit.
Thank you for choosing Mount-It
Mount-It!
Mount-It!
4
Step 3
• First, plan the route and mark it with a pencil, then measure the distance and determine the number of
cable channels needed and the number of connectors and each type. Refer to the diagram to determine
the exact spacing of each connector.
• To each Straight Channel (#A) add additional length to accommodate the connectors used:
Add 0.63” (16mm) for each Flat 90° (#B) or Exterior 90° (#D).
Add 1.3” (33mm) for each Interior 90° (#C).
Add 2.36” (60mm) for each end of the T-Fitting (#F)
Add 0.71” (18mm) for each Straight Coupling (#E)
Measure
Step 2
• Wipe the mounting area clean with a cloth or a duster. If the walls were cleaned using a liquid cleaner,
allow the surface to fully dry before proceeding.
Clean the Wall Surface
Step 1
Installation Option 1: Adhesive Tape
(Not suitable for rough or uneven surfaces)
0.63 inch
(16 mm) 1.30 inch
(33 mm)
0.71 inch
(18 mm)
2.36 inch
(60 mm)
0.63 inch
(16 mm)


Specyfikacje produktu

Marka: Mount-It!
Kategoria: nieskategoryzowany
Model: MI-7285

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mount-It! MI-7285, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany Mount-It!

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024