Instrukcja obsługi Mosconi Gladen Pro 5/30

Mosconi odbiornik Gladen Pro 5/30

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mosconi Gladen Pro 5/30 (1 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
PRO 5|30
4-channel AB class / 1-channel D amplifier [ Rev. 3.0 – 2017/10 ]
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CEA-2006-A SPECIFICATIONS
POWER RATING :(@ 4 Ohm < 1% THD+N) 70Wx2 + 150Wx2 + 550Wx1
SN RATIO :(ref.: 1 Watt into 4 Ohm) >75 dBA (CH1/2) >71 (CH3/4) >73 (CH5)
SN RATIO Direct DSP :(ref.: 1 Watt into 4 Ohm) >83 dBA (CH1/2) >76 (CH3/4) >76 (CH5)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
MOS SPECIFICATIONS (Tcase = 25 °C / 4 Ohm stereo / 0.2V input level @ 14.4 Volt if not otherwise specified)
TARGET POWER: 85x2 Watt (CH1/2), Watt (CH3/4), Watt (CH5) [@ 4 Ohm]170x2 600x1
REAL POWER ( ):
single section driven CH1/2: W W 95x2 @ 4 Ohm / 150 x2 @ 2 Ohm
1% THD [CH1/2/3/4] – 3% THD [CH5] CH3/4: W W 185x2 @ 4 Ohm / 290 x2 @ 2 Ohm
CH5: W W 660 @ 4 Ohm / 1030 @ 2 Ohm
REAL POWER ( ):
all sections driven 70x2 W (CH1/2) + W (CH3/4) + W (CH5)150x2 @ 4 Ohm 550x1 @ 4 Ohm
1% THD [CH1/2/3/4] – 3% THD [CH5] 65x2 W (CH1/2) + W (CH3/4) + W (CH5)135x2 @ 4 Ohm 760x1 @ 2 Ohm
W (CH1/2) + W (CH3/4) + W (CH5)85x2 195x2 @ 2 Ohm 750x1 @ 2 Ohm
Watt ( )1310 is the total amount of power the amplifier can deliver
THD (90% power rating ref.)
4 Ohm / ST mode < 0.045 % < 0.035 % < 1 % (CH1/2 - 1KHz) (CH3/4 - 1KHz) (CH5 - 100Hz)
2 Ohm / ST mode:< 0.05 % < 0.04 % < 1 % (CH1/2 - 1KHz) (CH3/4 - 1KHz) (CH5 - 100Hz)
DC-DC converter typology / Conversion frequency: Unregulated Push-Pull / 50 Khz (managed by microcontroller)
Supply voltage range operation: 9 V ÷ 16 V 11 V ÷ 14.4 V (Absolute maximum) / (Recommended)
Under / Over Voltage Safety Thresholds: 8 V 16 V(1 sec. 6V sustaining for Start & Stop) /
Mute delay time: 4 secs.
Secondary voltages (VDD#12 /VDD#34 /VDD#5 / DRIVE / SERV): ±33.1 V / ±45.3 V / ±84.7 V / ±14 V / ±15 V
Max output offset voltage (each channel): ±15 mV
Standby current: < 1 mA (typical)
Quiescent consumption @ 12V6 / 14V4: 1.90 A / 2.15 A (no idle current regutation)
Idle current regulation (no signal): 0.05 A (each trimmer)
Quiescent consumption @ 14V4: 2.25 A (with idle current setted)
Thermal protection consumption: 140 mA
Ground decoupling: (RCA Input) / 47R 1 KOhm (battery vs secondary) / (body vs battery)68 Ohm
Bandwidth (-3dB ÷ 1 Watt): < 5 Hz ÷ 135 KHz < 5 Hz ÷ 145 KHz < 5 Hz ÷ 1.75 KHz (CH1/2); (CH3/4); (CH5 10Watt)
Input sensitivity (Power rating ref): 0.35 V ÷ 12 V (5.3 V in DDSP mode) (3.1 V in DDSP mode) [CH1/2/3/4] 0.14 V ÷ 5.9 V [CH5]
Input impedance @ 1 KHz (STEREO input): 15 KOhm / 47 Ohm (LL) (HL)
S/N ratio – Power rating ref: (filter: 10 Hz - 500 KHz ) / (filter: 10 Hz - 22 KHz “A” weighted) 67 dB 94 dB
S/N ratio DDSP – Power rating ref: (filter: 10 Hz - 500 KHz ) / (filter: 10 Hz - 22 KHz “A” weighted) 69 dB 100 dB
Channel separation@ 100Hz / 1KHz / 10KHz – 10 Watt ref: 75 dB / 75 dB / 62 dB
Xover functions (selectable filters): CH1/2= HP: 43 ÷ 500Hz(x1) or 430 ÷ 5000Hz(x10) [12 dB/oct – Q: 0.7]
CH3/4= HP: 50 ÷ 200Hz & LP:(430 ÷ 5000Hz) [12 dB/oct – Q: 0.7]
CH5= LP: 43 ÷ 200Hz [24 dB/oct]
Special features: DDSP - Direct DSP (bypass all the preamplifier circuitry but the differential input interface)
HL/LL - High Level / Low Level selectable input
Controlled via uC – Internally controlled via Atmel Processor
Thermal cutoff Threshold: 90°C / 100°C (CH5 cutoff) (Overall cutoff) / (resume to normal operation)70°C
ProSPEED® Fan Controller Threshold: 50°C / 45°C / 70°C (start) (stop) (max speed)
Damping factor @ 100 Hz 10 Watt ref (Right / Left):- 319/397 318/487 153 [CH1/2] - [CH3/4] - [CH5]
Damping factor @ 1 KHz 10 Watt ref (Right / Left):- 291/375 304/453 101 [CH1/2] - [CH3/4] - [CH5]
Damping factor @ 10 KHz 10 Watt ref (Right / Left): - 178/199 183/219 n.a. [CH1/2] - [CH3/4] - [CH5]
Load drive limitations (*): 2 Ohm / 4 Ohm (Stereo / Bridged)
Suggested fuse: 150 A (Internal)
Size (mm): 500 / 205 / 55
Weight (Kg): 5.4
(*) VERY IMPORTANT NOTE - READ CAREFULLY
4 Ohm ST 8 Ohm BTL or CONTINUOUS SINEWAVE SIGNAL – pure resistive load or speaker load
2 Ohm ST 4 Ohm BTL or – pure resistive load or speaker loadMUSICAL SIGNAL
2 Ohm – pure resistive load or speaker load (only CH5)MUSICAL SIGNAL
All Right Reserved - Features may change without notice -


Specyfikacje produktu

Marka: Mosconi
Kategoria: odbiornik
Model: Gladen Pro 5/30

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mosconi Gladen Pro 5/30, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje odbiornik Mosconi

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon

Denon AVR-S900W Instrukcja

15 Października 2024
Pro-Ject

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024
AKG

AKG HP12U Instrukcja

15 Października 2024
Apart

Apart SBR160 Instrukcja

14 Października 2024
American Audio

American Audio VLP 600 Instrukcja

14 Października 2024
Chord

Chord Anni Instrukcja

14 Października 2024
Sennheiser

Sennheiser EM 9046 SU Instrukcja

14 Października 2024
Yamaha

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024
JL Audio

JL Audio VX600/6i Instrukcja

12 Października 2024
Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024