Instrukcja obsługi Moman H2

Moman zestaw słuchawkowy H2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Moman H2 (2 stron) w kategorii zestaw słuchawkowy. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
MOMAN
MOMAN
① On/Off Key
② Indicator Light
③ Function Key
④ Charging Interface
⑤ Knob
⑥ Headset Interface
⑦ Buckle Flap
⑧ Speaker
⑨ Headset Plug
⑩ Butterfly
sticker
⑪ Microphone
Press the On/Off Key for 2 seconds. When you
hear voice prompt, the blue indicator flashes twice.
The system enters the standby mode.
Press the On/Off Key for 2 seconds. When you
hear voice prompt, the red indicator flashes twice.
(1)Power on two intercoms and the blue indicators flash twice. The red and
blue indicators flash alternatively, which means two intercoms wait to be
Bluetooth paired.
(2)Then, press the On/Off Key of any one of them while the blue indicator
flashes quickly with voice prompting “Intercom Search”; the red and blue
indicator of the other keeps flashing alternatively. After few minutes, they are
paired automatically with blue indicator flashing slowly.
Press the Function Key for 2 seconds to disconnect the intercoms. Press it
again to reconnect.
※ The distance between intercom and mobile phone should be within 1 meter.
※ When two intercoms are paired successfully, there is no need to pair them
repeatedly. Under standby mode, they will be paired automatically after a few
seconds.
※ The automatic connection function is available within five minutes after
disconnection. If the connection fails again, you can manually press the
Function Key once for searching and matching.
(1) After power on, the blue indicator flashes twice. The red and blue indicator
flashes alternatively, which means the intercom waits to be Bluetooth paired.
(2) Turn on the Bluetooth function of the mobile phone, search and select
“MOMAN H2” to connect and pair. The voice will prompt “Bluetooth
connected”.
※ The distance between intercom and mobile phone should be within 1 meter.
※ If the intercom has pairing record with the mobile phone, they will be
connected after power on, provided that the Bluetooth is turned on.
press the Function Key
When the phone calls and there
is no operation after 8 seconds, it will answer the call
automatically.
press and hole the Function Key for 3
seconds until you hear the “beep” sound.
(1) Under Bluetooth connection mode, press the
Function Key to play/pause music.
(2) turn the Knob counterclockwise.
(3) turn the Knob clockwise.
When it is on, press On/Off Key and rotate the Knob to
change the language of voice prompt.
(1)In intercom mode, press the Function Key for 2 seconds and you hear “beep”,
indicating the intercom mode exits, and enter the switch between Music/FM
radio;
(2) Press the Function Key twice;
short press the Function Key;
long press the Function Key.
(1) If the machine is connected with mobile phone, the intercom will disconnect
when there is call. When the call ends, it will get back to the intercom mode,
which takes 5 seconds.
Mobile Phone
Intercom
Music/FM Radio
(1) continuously turn the Knob
counterclockwise.
(2) continuously turn the Knob clockwise.
※ There is voice alarm for two high or two low volume.
(1) under standby mode, press the Function
Key twice to switch to the FM radio.
(2) quickly rotate the Knob and
release to adjust and select channels. Continuously
rotate the Knob to select different channels. Rotate
the Knob continuously to enter volume adjustment.
(3) press the Function Key twice to get back
press the Function Key.
In standby mode, press the On/Off Key twice to dial the last call number.
to the previous mode.
※ If the signal is weak indoor, you could try to turn on the FM radio near
window or in the open area.
※ When FM radio is turned on and there is a phone calling, the machine will
cut off FM radio automatically and connect to the mobile phone. It gets back to
the FM radio when the call ends.
Specications
① Use the screwdriver to loosen the screws of the back clip so that it can open
to a proper extent.
② Open the helmet liner, insert the clip into the right position on the left side of
the helmet and tighten the screw.
③ Slide the intercom into the back clip slot to make sure it locks firmly.
④ Open the helmet liner (ear position), clean the EPS surface of the helmet,
and stick a piece of horn Velcro on the left and right sides of the helmet.
⑤ Stick the speaker on the fixed Velcro surface and the speaker with short line
should be installed close to the machine. Fix the microphone and arrange the
helmet lining and cable.
⑥ Insert the headset into the jack of the intercom and tie up the headset cable.
Separate the hook and loop fasteners. First stick the hook onto the Velcro
clip; choose the right installation position on the helmet and stick the loop to
the position. Install the intercom onto the Velcro clip.
The installation of speakers can refer to the description above.
First unplug the headset, then press the xed buckle in the middle of the
back clip with one nger (push towards the side of the helmet), so that
the back clip hook is detached from the intercom, and push the intercom
upwards to let it slide out of the back clip smoothly to complete the
disassembly.
Unscrew the screws on the back of intercom with
screwdriver, open the buckle ap, plug in the headset
plug and tighten the screws. If you need to plug
out the headset, please open the buckle ap by
unscrewing the screws.
1. Before using the Bluetooth intercom, please use the attached charging
cable to charge the intercom. The small type-C interface on the charging
line is connected to the USB charging interface of the Bluetooth intercom,
and the large USB connector on the charging cable is connected to the
following charging interface for power supply:
A. USB interface of computer;
B. A mobile power supply with DC 5V output;
C. A USB power adapter with DC 5V output.
2. When charging, the red LED is always on, and when fully charged, the red
light goes out slowly. It takes up to 2.5 hours to fully charge the unit.
1. If you do not use intercom for up to one month or more, please charge
the intercom once every two months in order to protect the lithium battery;
2. The storage temperature of this product is -20 ℃ to 50 ℃ , and do not
store in the environment with too high or low temperature, otherwise, the
service life of the product will be aected;
3. Do not expose this product to re to avoid explosion;
4. Only two screws on the back of intercom can be opened. Do not open
other screws to the intercom to avoid short circuit of main board or battery
damage.
℃

Specyfikacje produktu

Marka: Moman
Kategoria: zestaw słuchawkowy
Model: H2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Moman H2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje zestaw słuchawkowy Moman

Moman

Moman H2 Instrukcja

14 Grudnia 2024

Instrukcje zestaw słuchawkowy

Najnowsze instrukcje dla zestaw słuchawkowy

TELEX

TELEX AIRMAN 7P Instrukcja

19 Grudnia 2024
Gioteck

Gioteck EX-05 Instrukcja

19 Grudnia 2024
Gioteck

Gioteck EX-01 Instrukcja

19 Grudnia 2024
Gioteck

Gioteck EX-02 Instrukcja

19 Grudnia 2024
Gioteck

Gioteck TX-1 (Xbox 360) Instrukcja

19 Grudnia 2024
Gioteck

Gioteck HC-5 Instrukcja

19 Grudnia 2024
Gioteck

Gioteck HC-4 (PS4) Instrukcja

19 Grudnia 2024
Gioteck

Gioteck HC-3 Instrukcja

19 Grudnia 2024
Gioteck

Gioteck FL-400 (PS4) Instrukcja

19 Grudnia 2024
Gioteck

Gioteck FL-300 Instrukcja

19 Grudnia 2024