Instrukcja obsługi Mitsubishi L75-A91 Laservue

Mitsubishi Telewizor 3D L75-A91 Laservue

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mitsubishi L75-A91 Laservue (100 stron) w kategorii Telewizor 3D. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/100

MODEL

L75–A81

MODEL

L75–A91

Owner’s Guide

In the U.S. call 1(877) 675-2224 for assistance.

FCC Declaration of Conformity

Product: Projection Television Receiver

Models: L75-A81, L75-A91

Responsible

Party:

Mitsubishi Digital Electronics

America, Inc.

9351 Jeronimo Road

Irvine, CA 92618-1904

Telephone: (800) 332-2119

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1)

This device may not cause harmful interference,

and

(2) This device must accept any interference

received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential instal-

lation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may

cause harmful interference to radio communica-

tions. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

Reorient or relocate the receiving antenna. -

Increase the separation between the equip- -

ment and the receiver.

Connect the equipment into an outlet on -

a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/ -

TV technician for help.

Changes or modifications not expressly

approved by Mitsubishi could cause harmful

interference and would void the user’s authority

to operate this equipment.

Canadian Notice

For Model L75-A81

This Class B digital apparatus complies with

Canadian ICES-003.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or moisture.

This apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as

vases, shall be placed on the apparatus.

Cet appareil ne doit pas être exposé à des gouttes ou

à des éclaboussures et aucun objet rempli d’un liquide,

comme un vase, ne doit être placé sur l’appareil.

WARNING: This product contains chemicals known

to the State of California to cause cancer and/or birth

defects or other reproductive harm.

TV WEIGHT: This TV is heavy. Exercise extreme care

when lifting or moving it. Lift or move the TV with a

minimum of two adults. To prevent damage to the TV,

avoid jarring or moving it while it is turned on. Always

power off your TV, unplug the power cord, and discon-

nect all cables before moving it.

Stand Requirement

Mitsubishi does not design, manufacture or sell match-

ing bases for L75-A81 and L75-A91 model televisions.

When selecting a stand, base, or other furniture to

support the TV, please make sure it is designed with the

appropriate dimensions for stability and to support the

TV’s weight plus the weight of any additional equipment

you plan to store.

Children and Television Viewing

The American Academy of Pediatrics discourages

television viewing for children younger than two years of

age.

MAINS DISCONNECTION: The mains plug is used

as the disconnect device. The mains plug shall remain

readily operable.

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user of the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to consti-

tute a risk of electric shock to persons.

The exclamation point within an equilat-

eral triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

Note: Features and specifications described in this

owner’s guide are subject to change without notice.

In Canada call 1(800) 450-6487 for assistance.

Important Safety Instructions

Please read the following safeguards for your TV and

retain for future reference. Always follow all warnings

and instructions marked on the television.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart,

stand, tripod, bracket,

or table specified

by the manufacturer,

or sold with the

apparatus. When

a cart is used, use

caution when moving

the cart/apparatus

combination to avoid

injury from tip-over.

13) Unplug this apparatus

during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

ANT E NNA

LE AD IN W IR E

ANT E NNA

DIS C HAR G E U NIT

(NE C AR T IC LE 810-20)

G R OU NDING

C ONDUC T OR S

(NE C AR T IC LE 810-21)

G R OUND C LAMP S

P O W E R S E R V IC E G R OUNDING

E L E C T R ODE S Y S T E M

(NE C AR T 250, P AR T H)

G R OUND C LAMP

E LE C T R IC

S E R V IC E

E QUIP ME NT

NE C — NAT IONAL E LE C T R IC AL C O DE

E X AMP LE O F ANT E NNA G R OUNDING

Outdoor Antenna Grounding

If an outside antenna or cable system is connected

to the TV, be sure the antenna or cable system is

grounded so as to provide some protection against

voltage surges and built-up static charges.

Replacement Parts

When replacement parts are required, be sure the

service technician has used replacement parts speci-

fied by the manufacturer or have the same character-

istics as the original part. Unauthorized substitutions

may result in fire, electric shock or other hazards.

In the U.S. call 1(877) 675-2224 for assistance.

Laser Safety

This TV is in compliance with the requirements of IEC •

60825-1 Ed. 2(2007).

This TV is a CLASS 1 laser product. This TV poses •

no risk to eyes or skin during normal use. An expo-

sure hazard may exist only if the protective housing

is removed.

This TV contains a CLASS 4 laser device, which by •

itself may be hazardous. However, this TV incorpo-

rates a protective housing, optics and electronics

such that there should be no exposure to unsafe

levels of laser light during normal operation and

proper service.

Do not open this product. No consumer controls •

inside. Only a trained LASERVUE® technician

should service this TV. Please call Mitsubishi for

assistance.

In the U.S.A. call 1-877-675-2224. -

In Canada call 1-800-450-6487. -

Safe Operation

Always inspect the TV for damage after moving it. •

If the cabinet or screen is physically damaged, DO

NOT connect the TV to an AC outlet.

In the U.S.A. call 1-877-675-2224 for assistance. -

In Canada call 1-800-450-6487. -

DO NOT power on the TV until it has been repaired

by qualified service personnel authorized by

Mitsubishi. See “Service” on the next page.

Caution.• Use of controls or adjustments or per-

formance of procedures other than those specified

herein may result in hazardous radiation exposure.

Use external or remote controls to operate the •

product. Connection to signal sources and power

are accomplished through the external connectors.

Damage and Repair

There are no user serviceable components in this •

TV. Do not attempt to disassemble any part of the

TV.

If damaged, the device must not be powered on or •

used until it is repaired by qualified service person-

nel authorized by Mitsubishi. See “Service” on the

next page.

Under no circumstances shall attempts be made to •

operate this device without the screen in place or if

any portion of the enclosure, including the screen,

is cracked, broken, a liquid is spilled onto the TV or

is otherwise damaged.

CAUTION

CLASS 4 LASER LIGHT WHEN

OPEN AVOID EYE OR SKIN

EXPOSURE TO DIRECT OR

SCATTERED RADIAITON

ATTENTION

LUMIÈRE LASER DE CLASSE 4 - EN CAS

D’OUVERTURE EXPOSITION DANGERE-

USE AU RAYONNEMENT DIRECT OU

DIFFUS DES YEUX OU DE LA PEAU

This class-4 label and similar service warning labels

are located inside the back cover of the television in an

area that should not be accessed by the user under any

circumstances.

An additional class-4 label is located at the lower front

access panel under the front decorative bezel.

This class-4 label is located at the center back of the TV

under the outer cover.

This label is located on the right lower back of the

television set.

In the U.S. call 1(877) 675-2224 for assistance.

Contents

Important Information About Your TV

Important Safety Instructions ................ 2

Laser Safety ........................... 3

Installation and Operating Notes ............. 4

1 Basic Setup and Operation

Package Contents ....................... 6

Special Features of Your TV................. 7

TV Controls and Indicators ................. 8

First-Time Power-On ..................... 11

Setting Up TV Inputs..................... 12

Basic TV Operation...................... 14

Using the TV with a Personal Computer ....... 16

2 TV Connections

Before You Begin ....................... 18

Cable Management ..................... 18

Inputs and Outputs ...................... 19

Y Pb Pr Component Video Device ........... 21

DMI Device .............................21

DVI Video Device ....................... 22

Antenna or Cable TV Service ............... 22

Composite Video Device .................. 22

VCR or DVD Recorder to an Antenna or

Wall Outlet Cable ...................... 23

VCR or DVD Recorder to a Cable Box ........ 23

A/V Receiver .......................... 24

A/V Receiver with HDMI Output ............. 24

3 Using TV Features

Selecting an Input ...................... 25

Sleep Timer ........................... 25

ChannelView Channel Listings .............. 26

Redirecting Audio Output ................. 26

Controlling A/V Receiver Sound Volume ....... 26

Status Display ......................... 27

TV Signals and Display Formats ............. 28

3D Video ............................. 29

Camera and Music Files .................. 31

Streaming Internet Movies with VUDU ........ 34

Introduction to Home-Theater Control ........ 36

4 TV Menus

Main Menu ............................ 37

Menu Navigation ....................... 37

Adjust ............................... 38

Captions ............................. 42

Initial ................................ 43

Inputs ............................... 45

Lock ................................ 47

5 NetCommand IR Control

About NetCommand IR Control ............. 50

IR Emitter Placement .................... 51

Initial NetCommand Setup ................ 52

Operating NetCommand-Controlled Devices ... 53

6 NetCommand IR Control of an A/V Receiver

Controlling an A/V Receiver after

NetCommand Setup .................... 56

Setting Up A/V Receiver Control

Power and Volume ................... 57

Automatic Audio or Audio/Video Switching . . 58

Appendices

Appendix A: Programming the Remote Control . 64

Appendix B: Bypassing the Parental Lock ..... 71

Appendix C: HDMI Control of CEC Devices .... 73

Appendix D: TV Care .................... 76

Appendix E: Troubleshooting .............. 77

Trademark and License Information .......... 84

Mitsubishi TV Software .................... 85

Warranty .............................. 88

Index ................................. 92

In Canada call 1(800) 450-6487 for assistance.

Basic Setup and Operation

Package Contents

Please take a moment to review the following list of

items to ensure that you have received everything.

Remote Control Batteries

Remove the remote control back cover.1.

Emitter bulb

Load the batteries, making sure the polarities 2.

(+) and (-) are correct. Insert the negative (-)

end first.

Slide the cover back into place.3.

Remote Control1.

GUIDE MENU INFO BACK

ACTIVITY

Two AA Batteries2.

Owner’s Guide3.

Quick Setup Guide4.

Product Registra-5.

tion Card

Cable Tie6.

L75-A91: Four-ended 7.

IR emitter cable

1. Basic Setup and Operation 7

In the U.S. call 1(877) 675-2224 for assistance.

Welcome to LASERVUE® TV! Mitsubishi has created a

new category of television with laser technology. Laser

beams provide the widest range of rich, complex colors,

along with the most clarity and depth of field. Precise

and focused, the purity of laser light far surpasses

current high-definition technologies and sets a new

standard for premium large-screen television.

Your new high-definition widescreen television has

many special features that make it the perfect center of

your home entertainment system, including:

1080p High-Definition DLP Display System

Your Mitsubishi HDTV uses Texas Instruments Digital

Light Processing™ technology for rear-projection TVs

to create the picture you see on screen. All images are

displayed at 1080p. The TV uses Plush 1080p® 5G to

convert lower-resolution signals to 1080p for display.

The TV can also accept 1080p original signals and main-

tain them at 1080p through all processing until displayed.

3D Ready

All Mitsubishi 1080p LASERVUE HDTV’s are 3D Ready.

This feature lets you experience the new 3D technolo-

gies applied to many recent movies and video games.

Immerse yourself in your favorite video game, movie, or

sporting event displayed in 3D.

Integrated HDTV Tuner

Your widescreen Mitsubishi LASERVUE HDTV has an

internal HDTV tuner able to receive both over-the-air

HDTV broadcasts (received via an antenna) and non-

scrambled digital cable broadcasts, including non-

scrambled HDTV cable programming.

High-Definition Video Inputs

Component Video Inputs.• Also called Y/Pb/Pr

inputs, these inputs receive standard analog video

formats of 480i, 480p, plus 720p and 1080i high-

definition signals. This provides a high level of

flexibility when connecting DVD players/recorders,

cable boxes, and satellite receivers.

HDMI Inputs.• These inputs accept digital 480i,

480p, 720p, 1080i, and 1080p video signals plus

PCM digital stereo signals. The HDMI™ inputs can

also accept a variety of PC signals and resolutions.

These inputs support HDMI 1.3 Deep Color (up to

36 bits) and the x.v.Color extended color gamut.

Used with an adapter, these HDMI inputs also

accept compatible digital DVI video signals. HDMI

inputs provide additional high-performance,

high-definition connections for maximum flexibility

in your choice of home theater products. The HDMI

inputs are HDCP copy-protection compatible.

Easy Connect Auto Input Sensing

Easy Connect™ Auto Input Sensing automatically rec-

ognizes when you plug in a device and prompts you to

assign a name to it. The TV ignores any unused inputs,

so the result is an uncluttered menu where you can

easily find and select connected devices by name.

Home-Theater Control

HDMI Control

HDMI devices with Consumer Electronics Control

(CEC) capabilities may be compatible with the TV’s

HDMI Control feature. Compatible devices can receive

control signals through the HDMI connection, allowing

the TV’s remote control to operate some functions of

these devices.

NetCommand with IR Learning

Model L75-A91. Your Mitsubishi HDTV offers a new

level of networking that seamlessly integrates selected

older A/V products with new and future digital prod-

ucts. NetCommand® supports IR (infrared) control of

products such as VCRs, DVD players, cable boxes, and

satellite receivers. NetCommand can “learn” remote

control signals directly from many devices, allowing you

to create a customized NetCommand-controlled home-

theater system.

Internet-Video Ready

Model L75-A91. Built-in VUDU™ connectivity lets you

stream high-definition internet video content directly to

your TV. Access to VUDU’s fee-based movie service

is through menus displayed on the TV.

VUDU offers the

largest on-demand HD movie selection anywhere, featur-

ing full 1080p and 5.1 surround sound. VUDU allows you

to enjoy movies with no store visits, no mailing, no late fees

and no subscriptions.

ENERGY STAR®

This is an ENERGY STAR® qualified TV. Products that

earn the ENERGY STAR prevent greenhouse gas emis-

sions by meeting strict energy efficiency guidelines set

by the U.S. Environmental Protection Agency and the

U.S. Department of Energy.

This TV consumes energy in excess of ENERGY STAR

guidelines for a powered-down device under the follow-

ing conditions:

Model TV Condition

L75-A81

L75-A91

TV powered off, Fast Power On mode

enabled

L75-A91 TV powered off, External Controller Input

enabled

Special Features of Your TV

8 1. Basic Setup and Operation

In Canada call 1(800) 450-6487 for assistance.

Remote Control

TV Controls and Indicators

Note: To operate other audio/video

devices using the TV’s remote

control:

• SeeAppendix A, “Programming the Remote

Control.”

• ForHDMIdevicescompatiblewiththeTV’s

HDMI Control feature, see Appendix C.

• L75-A91. With NetCommand

See - page 50 for NetCommand IR “Learn-

ing” of device keys.

For use of specific keys with NetCom- -

mand-controlled devices, see “Special

Operation Methods,” page 53.

The MORE menu in TV mode

SLEEP

Sleep Timer, page 25

FORMAT

Picture shape (aspect ratio), page 28

Clears

the MORE menu.

Closed captions, page 42

VIDEO

Video adjustments, page 38

AUDIO

Audio adjustments, page 39

F1 F3 F4F2

FAV

DEMAND

GUIDE MENU INFO BACK

ACTIVITY

Powers TV on or off

Side button sets the control mode

for the type of device to operate. Set

mode to

for normal TV viewing.

Number/letter keys

Channel tuning, page 14

Displays a menu showing addi-

tional functions for the number

keys.

For the •

menu in TV mode,

see below.

With remote control programmed •

for another device, the

is specific to the device. See page

64.

For CEC-enabled devices, • page 75

CHANNEL UP

VOLUME UP

Record/Playback controls for external devices

When remote control is programmed, page 64

HDMI control, page 75

L75-A91: NetCommand, page 55

VCR

CABL/SAT

DVD

AUDIO

Control-mode indicator for device

type to control. Use the side button to

change.

MUTE

VOLUME DOWN

LAST

Returns to the previously tuned

channel.

CHANNEL DOWN

GUIDE

ChannelView listings, page 26

TV main menu, page 37

INFO

TV status (

page 27)

or TV help.

BACK

Steps back one menu; clears

the top menu or Status Display.

(

PAUSE

)

Freezes a broadcast TV picture.

Adds a separator when entering digital

channel numbers. Clears some menu entries.

Press to select a TV activity and input.

See page 25.

L75-A91. See page 64.

PAGE UP

ENTER

Selects a channel number or

menu item.

Navigation controls

PAGE DOWN

1. Basic Setup and Operation 9

In the U.S. call 1(877) 675-2224 for assistance.

TV Control Panel

Buttons on the control panel duplicate some keys on

the remote control.

Refer to • left labels when no TV menus are dis-

played.

Refer to • right labels when using TV menus or after

activating a special function.

System Reset

If the TV fails to respond to the remote control, the

control-panel buttons, or will not power on/off, perform

System Reset. Recent setting changes made before

using System Reset may be lost.

To perform System Reset, press and hold the

POWER

button on the control panel for ten seconds.

Panel-Lock Release

To • release the Panel Lock using the TV control

panel, press and hold the

ACTIVITY

button on the

control panel for ten seconds. If the TV is off, press

the

POWER

button to make it power on.

To activate the Panel Lock, use the • Lock menu,

page 49.

TV Controls and Indicators, continued

10 1. Basic Setup and Operation

In Canada call 1(800) 450-6487 for assistance.

Key

Off

Steady On

Slow Blinking

Fast Blinking

POWER Indicator

LED Color TV Condition Additional Information

None TV is powered off. Normal operation.

Green TV is powered on. Normal operation.

Green TV powered off, auto-on TV Timer is set. Normal operation. TV can be turned on at any time.

Green TV power just turned on. Normal operation. A picture will appear shortly.

TV just plugged into AC outlet.•

AC just restored after power failure.•

TV is rebooting after power fluctua-•

tion or receiving abnormal digital

signals from a digital channel or

digital device.

You have begun the procedure to •

update software from an authorized

flash memory device.

Wait approximately two minutes for blinking to stop before

turning on. Normal operation.

Yellow TV is too hot.

The TV will display a warning message and shut off if it over-

heats.

• Ambientroomtemperaturemaybetoohigh.Turnoff

the TV and let the room temperature drop.

• Clearblockedairvents.Ensureatleastafour-inch

clearance on all sides of the TV.

Red

TV may require service.

Turn off the TV and unplug the set from the AC power

source. Wait one minute and then plug the set back in. See

Appendix E.

If the LED is still on, contact Mitsubishi to receive Authorized

Service Center information:

U.S.A. Go to www.mitsubishi-tv.com or call 1-877-675-2224.

Canada. Go to www.MitsubishiElectric.ca or call

1-800-450-6487.

POWER

TV Controls and Indicators, continued

12 1. Basic Setup and Operation

In Canada call 1(800) 450-6487 for assistance.

Setting Up Other Inputs

Connect your devices to the TV, making note of

which TV input jack is used for each device. See

“TV Connections,” page 18, for recommendations.

Power on the devices to ensure detection.

Power on the TV.

The TV will display the New Device Found screen

for each new connection it detects Learn more

about Auto Input/Auto Output Sensing on the

opposite page.

Select the device type from the list on screen.

Sample New Device

Found screen.

Important Note for NetCommand IR Users

L75-A91. Be sure to select the correct device type

here. Although you can change the device type later

in the Inputs > Name menu, any “learned” NetCom-

mand IR codes will be erased when you make the

change.

L75-A91.

You can perform NetCommand IR “learn-

ing” after selecting the device type or at a later

time when convenient. To perform now, high-

light NetCommand and press

ENTER

. See

“Initial

NetCommand Setup,” page 52 or “Setting Up A/V

Receiver Control,” page 57.

Press

BACK

to close the New Device Found screen.

The TV will then display the New Device Found

screen for the next connection it finds.

Using the ANT (Antenna) Input

If using an antenna or direct cable service (no cable

box), connect the incoming coaxial cable to the TV’s

ANT

input. Refer to page 22.

You must save channels to memory with a channel scan

to enable reception of all available high-definition and

standard-definition digital channels. The channel scan

will search for channels available locally. If you skip

this step, the TV can receive only analog channels.

Memorizing Channels with Channel Scan

For the ANT input

To start channel memorization

Power on the TV.

Press

and open the Initial > Channel menu.

Start channel memorization from the Initial > Channel

menu.

Press

ENTER

to enter the menu.

Select

Ant Air if connected to an

over-the-air antenna. Select Ant

Cable for direct cable.

Highlight

Scan and press

ENTER

Channel memorization may take up

to 15 minutes to complete.

To stop channel memorization before completion,

press

CANCEL

Use the Initial > Channel > Edit menu (page 44) for

additional channel options, such as adding or deleting

channels from memory.

Setting Up TV Inputs

1. Basic Setup and Operation 13

In the U.S. call 1(877) 675-2224 for assistance.

About Auto Sensing

This TV’s Easy Connect™ Auto Sensing feature

detects most connections automatically. The excep-

tions are:

A connection on the •

ANT

input

An HDMI device that is powered off. Power on •

the device to ensure detection.

Auto Input/Auto Output Sensing for Most Devices

When you first connect a device, the TV will:

a. Detect the connected device and automati-

cally switch to it.

b. Prompt you to identify the device type.

c. L75-A91. Prompt you to perform NetCom-

mand set-up for the device, if available.

d. Repeat these steps for other newly detected

devices.

When You First Connect a Device

Most Device Types.• Select the device type from

the on-screen list. The device type you select

here will appear as a device icon in the

Activity

menu.

A/V Receiver•

T -

he TV can detect audio connections on the

DIGITAL AUDIO OUTPUT

jack (orange) and the

right (red)

AVR AUDIO OUTPUT

jack.

For an HDMI A/V receiver, select - AVR from

the list of device types if the A/V receiver is

not recognized automatically.

HDMI CEC Devices Compatible with the TV’s •

HDMI Control Feature.

Compatible CEC-

enabled HDMI devices are often recognized auto-

matically by the TV.

HDMI Control may allow you

to control some functions of a CEC-enabled device.

See Appendix C, “HDMI Control of CEC Devices.”

New Device Found screen for a device with HDMI

control enabled. Select On to enable the TV’s CEC

control of the device. In some cases, as in the

example above, you will also be prompted to select a

device name.

Tips on Auto Sensing

Choose a different name for each input.•

The antenna input (•

ANT

) is never detected,

although you can turn off the unused antenna

input in the Inputs > Name menu.

Change the device type displayed in the • Activity

menu by using the Inputs > Name menu (page

45).

L75-A91.• Any “learned” NetCommand IR codes

will be erased if you change the device type in

the Inputs > Name menu.

Reactivating Auto Input Sensing

for an HDMI Input

When you disconnect an HDMI device, Auto Input

Sensing is disabled until you perform these steps.

Disconnect the HDMI device.

Delete the removed HDMI device in the

Inputs >

Name menu (see “Removing an HDMI Device,”

page 75).

Connect the new device and the

New Device

Found screen will display.

Setting Up TV Inputs, continued

14 1. Basic Setup and Operation

In Canada call 1(800) 450-6487 for assistance.

Selecting an Input to Watch

Press

ACTIVITY

Press

and to highlight an input.

Press

ENTER

to switch to the input.

Watching Broadcast TV

TV Connected to an Antenna, Direct Cable, Cable

Box, Set-Top Box, or Satellite Receiver

Press

ACTIVITY

Press

and to select a broadcast source. If

you named devices during Auto Input Sensing,

select an input from the Watch TV group. Note:

Your TV may have only one group (Watch TV).

Note: For more about the Activity menu, see page 25.

Activity menu, antenna input selected

Tune to a channel on the

3. ANT

input using any of

these methods.

Enter the channel number using the number •

keys on the remote control and press

ENTER

For a two-part digital channel, such as 3-1,

press

—

CANCEL

to enter a dash (separator).

Press •

CHANNEL UP /CHANNEL DN

(

–

) to change

channels one channel at a time.

Press •

(LAST)

to switch back to the previ-

ously tuned channel.

Antenna or Direct Cable Only.• Press

GUIDE

display ChannelView channel listings, highlight

a channel number, and press

ENTER

to tune.

Note: Program information is provided by

broadcasters and may not be available in all

areas.

Watching DVDs or Videos

TV Connected to a DVD Player, DVR, or VCR

Press

ACTIVITY

and select a movie source from the

Activity menu. If you named devices during Auto Input

Sensing, select the input from the Watch Movie group.

Activity menu, DVD input selected

Basic TV Operation

1. Basic Setup and Operation 15

In the U.S. call 1(877) 675-2224 for assistance.

Making Picture Adjustments

To get the best picture under different viewing con-

ditions, set the Picture Mode before changing other

video settings. See page 38 for more.

a. Press

MORE.

b. Press

(VIDEO).

c. Press to make one of these Picture Mode

selections:

Name When to Use

Super

Brilliant

Under harsh retail lighting; not

recommended for home use

Brilliant

Under bright light

Game

With gaming consoles

Bright For most daytime viewing

Natural For most nighttime viewing

Cinema For recreating theater colors

Press

to display the name of the next adjust-

ment you want.

Press

to make the adjustment.

Additional picture adjustments are described on pages

40 and 41.

Audio Settings

Changing the Audio Output

To switch audio output from the internal TV speakers to

a connected external sound system or headphones:

Press

(AUDIO).

Press

until the Speakers option is displayed.

The Speakers option will display only if a connec-

tion has been detected on one of the TV’s audio

outputs.

Press

to switch between TV and either AV

Receiver or Headphones.

Changing Audio Settings

Press

(AUDIO).

Press

to display the name of the adjustment

you want.

Press

to change the setting.

Other TV Features

Activate Audio Lock to control your sound system •

with the TV’s remote control left in

mode. See

page 65.

To set the TV Clock see • page 43. Set the TV

Clock if you plan to use the TV Timer (page 43) or

ChannelView (page 26) features.

To set parental controls, see the • Lock menu, page

47.

Note: L75-A91. To set parental controls for

VUDU™ service, use the VUDU Info & Settings

menu.

To change the input names that appear in the •

Activity menu, see Inputs > Name options, page

45.

3D Video.• See page 29.

To program the remote control to operate other •

A/V devices, see Appendix A, “Programming the

Remote Control,” page 64.

To control compatible devices using HDMI CEC •

control, see Appendix C, “HDMI Control of CEC

Devices,” page 73.

To view still and moving digital camera images on •

the TV, see “Camera and Music Files,” page 31.

L75-A91.• To control A/V devices with NetCom-

mand, see chapter 5, “NetCommand IR Control for

Most Devices” on (page 50).

L75-A91.• See page 34 for internet video streaming

with VUDU™.

Basic TV Operation, continued

Other Information

TV Care

Remote Control.• See “Care of the Remote

Control” on page 76

General Cleaning.• See “Cleaning Recommenda-

tions,” page 76.

Assistance

For basic troubleshooting, see • Appendix E, page

77.

For service, and product support, see • page 4.

For warranty information, see the TV warranty on •

page 88.

16 1. Basic Setup and Operation

In Canada call 1(800) 450-6487 for assistance.

Connecting a Computer to the TV

Use one of the connection methods listed below based

on your computer’s video output.

Computer

Video Output

Video Connection Audio

Connection

Digital DVI DVI-to-HDMI cable

or an HDMI cable

with an HDMI-to-

DVI adapter

Stereo audio

cables

Note: If the computer’s audio output

is a single mini jack, a mini audio-to-

RCA-male “Y” adapter cable is also

required.

HDMI HDMI-to-HDMI

cable

No additional

audio connec-

tion is required.

IMPORTANT

This TV accepts digital computer signals only.

Connect the computer’s digital signal output to one

of the TV’s

HDMI

jacks. See the connection dia-

grams for the method suited to your equipment.

Connect the computer’s audio output using one of

these options:

• FordigitalDVIsignals,connectanalogleft/right

audio to the TV’s

DVI/PC INPUT AUDIO

jacks.

• ForHDMIsignals,noadditionalaudioconnec-

tion is required.

Power on the TV and computer. The TV will detect

the connection and display the New Device Found

screen.

In the

New Device Found screen, press to

highlight PC in the list of device types. It is impor-

tant to use the name PC so that the TV processes

the computer signal correctly.

Press

BACK

to close the New Device Found screen.

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

Computer with

HDMI output

panel

An HDMI-to-HDMI connection carries all video and

audio on a single cable.

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

DVI/PC L

RINPUT

DVI/PC L

RINPUT

DVI

OUT

AUDIO

Computer with

DVI and analog

stereo outputs

A DVI connection from a personal computer requires a

separate audio connection.

Note: If your computer provides digital audio out-

put (coaxial or optical), you can connect it

directly to a digital A/V receiver and bypass

the TV.

Using the TV with a Personal Computer

1. Basic Setup and Operation 17

In the U.S. call 1(877) 675-2224 for assistance.

Tip

Set the computer’s screen saver to display a pattern

after several minutes of inactivity. This acts as a

reminder that the TV is powered on.

Computer Video Adjustments

Power on the computer.

Select

PC from the Activity menu. To do this,

press

ACTIVITY

to open the Activity menu, move the

highlight to the PC icon, and press

ENTER.

Working from the computer, change the resolution

of the computer image. View the computer image

on the TV and maximize the computer resolution

while maintaining a suitable aspect ratio for the

image.

Perform TV video adjustments.

Press

then press

(VIDEO). Use

to cycle through video-adjustment

options.

Press

then press

(FORMAT)

repeatedly to find the picture format

(aspect ratio) best suited to the image.

See the chart on this page showing

how different computer resolutions

can be displayed on the TV.

Image Resolution

Your Mitsubishi TV can display the resolu-

tions shown in the chart from standard

VGA (640 x 480) through 1920 x 1080

signals at a refresh rate of 60 Hz.

In most cases, the computer will select

the best resolution match to display on

the TV. You can override this setting if you

wish. Refer to your computer operating

system’s instructions for information on

changing the screen resolution.

You may need to restart the computer for

changes to take effect.

Using the TV with a Personal Computer, continued

Distortion in Computer Images

Computer images may show distortion

when viewed on the TV, e.g., lines that

should be straight may appear slightly

curved.

Computer Display Formats

Press

then press

(FORMAT) repeatedly to cycle through the

TV displays available for your computer’s video signal.

Computer Signal

As Displayed on TV Screen

Original Format 4 X 3

Standard

16 X 9

Standard Zoom

VGA

640 X 480

SVGA

800 X 600

Original Format Standard Zoom

XGA

1024 X 768

PC 720p

1280 X 720

WXGA

1360 X 768

SXGA

1280 X 1024

Original Format Standard Reduce

PC 1080p

1920 X 1080

In Canada call 1(800) 450-6487 for assistance.

2TV Connections

Auto Input Sensing

The TV’s Auto Input Sensing feature automatically rec-

ognizes most connections and prompts you to identify

the type of device connected. See page 13 for more on

Auto Input Sensing.

Connection Types

Use the connection types available on your input

devices that will give the best video quality. For

example, choose HDMI over component video, and

choose component video over composite video.

Picture Quality

For best picture quality, route signals directly from the

input device to the TV whenever possible.

Surround Sound

For best surround sound audio quality, route audio-

signal cables or HDMI cables from the source device

directly to your A/V receiver or sound system.

IMPORTANT

Accessory items such as cables, adapters,

splitters, or combiners required for TV

connections are not supplied with the TV.

These items are available at most electronics

stores.

Before You Begin

Cable Management

Install the cable tie

(supplied) in one of

the mounting holes

on the back.

Lock the cable tie in place

by pushing the end into

the mounting hole.

To remove the cable tie,

squeeze the side tabs and

pull out.

Sample cable routing. Secure

the cable bundle with the

release tab facing out.

Press the release tab to

loosen the cable tie.

2. TV Connections 19

In the U.S. call 1(877) 675-2224 for assistance.

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

Inputs and Outputs

HDMI

(page 21)

LAN

(page 34)

USBa

(power

only, page 34)

RS-232

AVR AUDIO

OUTPUT

(page 24)

DVI/PC INPUT

(audio input,

page 22)

DIGITAL AUDIO

OUTPUT

(page 24)

VIDEO

(composite video,

page 23)

Y Pb Pr

(component video,

page 21)

ANT

(page 22)

–

NetCommand

Output/External Con-

troller Input

(page 51)

3D GLASSES EMITTER

(page 29)

USB

(page 31)

IR-NetCommand

Output/External

Controller offered

on L75-A91.

RS-232 control

jack is offered on

L75-A91.

HDMI 4 offered

on L75-A91.

1. ANT (Antenna)

Connect your main antenna or direct cable service

(no cable box) to

ANT

. The

ANT

input can receive

digital and analog over-the-air channels from a

VHF/UHF antenna or non-scrambled digital/analog

cable source.

2. 3D GLASSES EMITTER

Use this jack for the special IR emitter supplied

with 3D glasses. The emitter will send a signal that

synchronizes your 3D glasses with the screen display.

See page 29

3. IR–NetCommand Output/External

Controller Input

Connect IR emitters to this jack to send control

signals to external IR-controlled devices. This jack

can also serve as the input for an external controller.

4. Y Pb Pr (Component Video)

Connect devices with component video outputs to

this jack. Use the adjacent

INPUT 1/INPUT 2

audio

and

jacks if you wish to send audio to the TV.

VIDEO

(Composite Video)

Connect a VCR, DVD player, standard satellite

receiver, or other A/V device to the TV. Use the

adjacent

INPUT 1/INPUT 2

audio

and

jacks if you

wish to send audio to the TV.

6. L/R (Left/Right Analog Stereo Inputs)

Use with

INPUT 1/INPUT 2

video inputs, items

4 and 5.

USBa and LAN jacks

offered on L75-A91.

20 2. TV Connections

In Canada call 1(800) 450-6487 for assistance.

Inputs and Outputs, continued

7. HDMI™ Inputs

(High-Definition

Multimedia Interface)

The HDMI inputs support uncompressed standard and

high-definition digital video formats and PCM digital

stereo audio.

Mitsubishi recommends you use category 2 HDMI

cables, also called high-speed HDMI cables, to

connect HDMI 1.3 source devices. High-speed cat-

egory 2 cables bring you the full benefits of Deep Color

and x.v.Color.

These HDMI inputs can also accept digital DVI video

signals. To connect a device’s DVI output to the TV’s

HDMI input, use an HDMI-to-DVI adapter or cable plus

analog audio cables. Connect the analog audio cables to

the

DVI/PC INPUT AUDIO

jacks on the TV to receive left

and right stereo audio from your DVI device.

Use the HDMI inputs to connect to CEA-861 HDMI com-

pliant devices such as a high-definition receiver or DVD

player. These inputs support 480i, 480p, 720p, 1080i,

and 1080p video formats.

The TV’s HDMI inputs are compatible with many DVI-D

and HDMI computer signals.

These inputs are HDCP (High-Bandwidth Digital Copy

Protection) compliant.

8. DIGITAL AUDIO OUTPUT

This output sends Dolby Digital or PCM digital audio

to your digital A/V surround sound receiver. Incoming

analog audio is converted by the TV to PCM digital audio.

If you have a digital A/V receiver, in most cases this is the

only audio connection needed between the TV and your

A/V receiver.

HDMI Cable Categories

HDMI cables are available as Standard and

High-Speed types.

High-Speed HDMI Cables • (also called Category 2

Cables). Newer DVD players, video games, and set-top

boxes require High-Speed HDMI cables, suitable for

clock frequencies up to 340 MHz or data rates of up to

10.2 gigabits per second. Use high-speed cables for

1080p HD signals carrying extended color encodings

(i.e., 30 or more bits, also called Deep Color). High-

Speed HDMI cables are also suitable for standard HDTV

signals.

Standard HDMI Cables• (also called Category 1 Cables).

Standard HDMI cables may be unmarked. They are suit-

able for standard HDTV 720p, 1080i, and 1080p signals

with 8-bit color depth. Use category 1 cables for clock

frequencies up to 74.25 MHz or data rates of up to 2.23

gigabits per second.

9. DVI/PC INPUT AUDIO

When connecting a DVI device to one of the TV’s HDMI

inputs, use these jacks for left and right analog audio.

10. AVR AUDIO OUTPUT

Use

AVR AUDIO OUTPUT

to send analog audio of the

current program to an analog A/V surround sound

receiver or stereo system. Digital audio from digital

channels and HDMI devices is converted to analog

audio by the TV for output on this jack. This is the only

audio connection needed to the TV if using an analog

A/V receiver or stereo system.

Headphones. These jacks can also be used for head-

phones that accept standard line level audio signals.

An adapter may be required.

11. USB

The TV can read JPEG photo files and mp3 music files

from a USB device connected to the USB port.

12. RS-232C

L75-A91. Use the RS-232C interface to receive control

signals from compatible home-theater control devices.

See www.mitsubishi-tv.com for a list of control signals

for this interface.

13. LAN

L75-A91. Use the

LAN

Ethernet jack for streaming

internet video to the TV. See page 34 for setup. Visit

www.VUDU.com for details about VUDU™ service.

14. USBa

L75-A91. Standard USB 5-volt, 500-milliamp power

output you can use to supply power to an accessory

device. For use with the VUDU wireless adapter, see

page 34.

22 2. TV Connections

In Canada call 1(800) 450-6487 for assistance.

DVI Video Device

Cable Box, Satellite Receiver, DVD Player

Connect DVI devices (digital only) to the TV’s HDMI

input jacks.

Required:

1. DVI-to-HDMI cable or DVI/HDMI adapter and

HDMI cable

2. Analog stereo audio cables

If you are using a DVI/HDMI adapter, it is important to

connect the adapter to the DVI device for best perfor-

mance.

Some devices require connection to an analog input

first in order to view on-screen menus and to select DVI

as the ouput. Please review your equipment instruc-

tions for DVI connectivity and compatibility.

Note: The HDMI connection supports copy protection

(HDCP).

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

DVI/PC L

RINPUT

DVI/PC L

RINPUT

DVI

OUT

AUDIO

Digital DVI

device

panel

Antenna or Cable TV Service

Connect the incoming cable to the TV’s

ANT

input.

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

ANT

IN OUT

Cable TV

service

UHF/VHF

antenna

TV panel

Not recommeded.

Other connection

types provide better

quality audio and

video.

Direct cable (no cable box)

Older

cable

box

300-ohm-to75-

ohm combiner

(side view)

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

AUDIO OUT

COMPOSITE

VIDEO OUT LR

Y/ VIDEO

TV panel

Composite

video cable

VCR or other device with

composite video output

Composite Video Device

VCR or other device with composite video

output

Required:

1. Composite video cable (usually yellow)

2. Analog stereo audio cables.

2. TV Connections 23

In the U.S. call 1(877) 675-2224 for assistance.

VCR or DVD Recorder to an

Antenna or Wall Outlet Cable

Required:

1. Video cables

1a. Component video cables (red/blue/green)

1b. Composite video cable (usually yellow)

2. Left/right analog audio cables.

3. Two-way RF splitter

4. Two coaxial cables

Note:

Use composite video only if component video or •

HDMI are unavailable. For an HDMI connection

between the TV and recorder, see page 21.

If your recording device has an analog-only tuner, •

you must use a digital converter box to enable

recording of digital broadcasts.

2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

AUDIO OUT

COMPOSITE

VIDEO OUT COMPONENT

VIDEO OUT

Pb Pr

Y/ VIDEO

Pb Pr

ANT

ANTENNA

1a.

3. 4.

1b. or

DVD Recorder or VCR

Incoming

cable

RF Splitter

VCR or DVD Recorder to a Cable Box

Required:

1. Video cables

1a. Component video cables (red/blue/green)

1b. Composite video cable (usually yellow)

2. Left/right analog audio cables.

3. One coaxial cable

4. Video and audio cables required to connect the TV

to the cable box.

Notes: Use composite video only if component video or

HDMI are unavailable. For an HDMI connection

between the TV and recorder, see page 21.

When using this connection conﬁguration, it is

possible to view live cable programs through the

recording device. For best picture quality always

view live cable programs directly from the TV input

connected to the cable box device.

2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

AUDIO OUT

COMPOSITE

VIDEO OUT COMPONENT

VIDEO OUT

Pb Pr

Y/ VIDEO

Pb Pr

ANT

ANTENNA

OUT

1a.

1b. or

DVD Recorder or VCR

Incoming cable

Audio and video

from cable box

directly to TV,

preferably HDMI or

componenet

connections.

24 2. TV Connections

In Canada call 1(800) 450-6487 for assistance.

A/V Receiver

Most setups require either a digital audio cable or

analog stereo audio cables. To send audio from TV

channels received on the

ANT

input or devices con-

nected directly to the TV, you must use one of the

connections shown below. Usually, only one of these

connections is required.

The TV makes all audio available in digital and analog

formats:

Analog audio coming into the TV is available as •

output in digital stereo format on the

DIGITAL

AUDIO OUTPUT

jack.

Digital incoming audio is available as analog output •

on the

AVR AUDIO OUTPUT L

and

jacks.

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

OPTICAL

INPUT

COAXIAL

INPUT

COAXIAL

INPUT

DIGITAL

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

AVR AUDIO OUTPUT

Digital coaxial

cable (for a digital

A/V receiver)

Stereo analog cables

(for an analog A/V receiver)

A/V receiver

back panel

Note:

On rare occasions, an HDMI signal may be •

copy-restricted and cannot be output from

the TV as a digital signal. To hear these copy-

protected signals through the A/V receiver, use

the connection for an analog A/V receiver.

Check the A/V receiver’s Owner’s Guide for •

information concerning use of the digital input

and switching between digital sound and

analog stereo sound from the TV.

A/V Receiver with HDMI Output

Required: One HDMI-to-HDMI cable

Optional: One digital coaxial audio cable or analog

stereo audio cables

This option allows you to view content from devices

connected to an A/V receiver. The A/V receiver can

send audio and video to the TV over a single HDMI

cable.

In addition to the HDMI connection, you can use •

an audio connection from one of the TV’s audio

outputs. The optional audio connection allows you

to hear, through the A/V receiver, devices con-

nected to the TV only, e.g., an antenna on the

ANT

input.

You may be able to use the TV’s remote control (in •

mode) to operate connected CEC-enabled HDMI

devices. See Appendix C, page 73.

L75-A91.• This setup allows you to use NetCom-

mand-controlled audio and video switching over the

HDMI cable. See “Case 3: Automatic Audio and

Video Switching via HDMI” on page 60.

L75-A91.• To use NetCommand to supplement

HDMI control of a CEC-enabled A/V receiver, note

the recommendations under “More About Using an

HDMI Connection,” page 60.

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

HDMI

OUT

A/V receiver

with HDMI

output

Any connec-

tion types

(can be HD or

SD video)

AUDIO

DIGITAL

AUDIO IN

VCR

Cable box

DVD player

DIGITAL

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

AVR AUDIO OUTPUT

Optional audio

connection

(analog or digital)

HDMI

cable

In the U.S. call 1(877) 675-2224 for assistance.

Using TV Features

Selecting an Input

The Activity menu lets you switch TV inputs. If you named

devices during Auto Input Sensing, the inputs are organized

into groups based on possible ways to use each device.

Dots indicate the number of devices in each group. Note:

Your setup may have only one group (Watch TV).

Press the

ACTIVITY

key.

Use

to move through groups of TV inputs.

Use

to select an input.

Press

ENTER

to switch to the input.

To change the list of inputs shown in each activity group, •

see Inputs > Activity, page 45.

To assign or change the names of input icons, use the •

Inputs > Name menu, page 45.

Sleep Timer

The Sleep Timer turns the TV off after the length of time you set.

To set the TV to turn on at a certain time of day, see the Initial > Timer menu on page

43.

Setting the Sleep Timer

Press

on the remote control. The TV’s MORE menu will display.

Press

CANCEL

(SLEEP) repeatedly to increase the time in 30-minute increments.

The maximum is 120 minutes.

Press

BACK

or wait five seconds without pressing any keys for the message to dis-

appear.

Viewing the Sleep Timer

Press

INFO

to see the time remaining on the Sleep Timer.

SLEEP

With the MORE menu

displayed, press the

CANCEL key on the

remote control to

activate/deactivate the

Sleep feature.

26 3. Using TV Features

In Canada call 1(800) 450-6487 for assistance.

ChannelView Channel Listings

ChannelView displays program descriptions sent by

broadcasters. This information may be unavailable

in some areas.

ChannelView. Programs for the tuned channel are

listed on right side of screen.

ChannelView™ shows memorized channels on the

ANT

input. It displays channel names and program infor-

mation for digital channels as sent by broadcasters or

your local cable service provider (information may be

unavailable in some areas)

No program information is

displayed for analog channels.

Note: You must set the TV Clock (page 43)

o receive

ChannelView listings for the current channel.

Using ChannelView

Feature Instructions

Display/hide ChannelView

listings from the ANT

input.

GUIDE

Receive updates for a

digital channel.

Press 1. to

highlight a channel

number.

Press the 2.

INFO

key

(the screen may

briefly go blank).

Scan channels one by one. Hold or

Scan channels quickly.

Hold

PAGE UP/PAGE DN

Jump to listings for a spe-

cific channel.

Enter the channel 1.

number.

Press 2.

ENTER

See more of the program

description for the current

channel (if available).

INFO

Tune to the highlighted

channel.

ENTER

Redirecting Audio Output

Selecting an Audio Output Device

Press

and then

(AUDIO)

Press

to show the Speakers option. The

Speakers option will display only if there is a rec-

ognized audio device on an audio output or HDMI

input.

Press

to select either AV Receiver, Head-

phones, or TV.

Note: The Headphones option displays only if you

selected the name Headphones in the New

Device Found screen.

Disconnecting an Analog A/V Receiver

When you disconnect an analog A/V receiver, change

the Speakers setting to TV to hear sound from the TV

speakers. Change the setting using the remote con-

trol’s

(AUDIO

)key or the Adjust > Audio >

Speakers menu.

Controlling A/V Receiver Sound

Volume

Use one of the methods below to control sound volume from

an A/V receiver.

With a Standard TV Setup

Recommended Method:• Program the TV’s

remote control for your A/V receiver and enable the

Audio Lock feature. See page 65.

Program the TV’s remote control for your A/V •

receiver and set the TV remote control’s mode to

AUDIO

. Return the control mode to

to control the

TV.

Use the remote control that came with the A/V •

receiver.

With HDMI Control (CEC-Enabled HDMI

A/V Receiver)

The TV’s remote control may control some functions of

the A/V receiver. See Appendix C, “HDMI Control of

CEC Devices,” page 73.

With NetCommand IR Control

Model L75-A91. Set up NetCommand control of the A/V

receiver’s volume functions in the Inputs > AVR menu.

The TV’s remote will then control A/V receiver volume.

See page 57.

3. Using TV Features 27

In the U.S. call 1(877) 675-2224 for assistance.

Press the

INFO

key to see

the on-screen status

display. The most

common displays are

shown here.

Sample information

from the on-screen

status display

1. Current Input

2. Audio Indicator.

TV speakers External sound system

Headphones Mute

3. Channel number (antenna source only)

Digital channel includes major and sub-channel

numbers.

4. Digital channel name (if broadcast); antenna

source only.

V-Chip rating

Antenna source only for digital signal•

Antenna or •

VIDEO

composite jack for

analog

signal

6. Program name (if broadcast); digital source only

7. Program description (if broadcast); digital

source,

antenna only. Press the

INFO

key additional

times to see more of the description.

8. Sleep Timer remaining time

9. Day and time

10. Signal type being received

11. Screen format in use

12. Program Audio indicator (antenna source only)

Digit•

al source: Stereo, Surround

Anal•

og source:

Stereo, Stereo SAP, SAP

13. Available language (digital source, antenna only)

14. Signal-strength indicator (digital source, antenna

only)

Status Display

402-101 KABC Monday Night Football

TV-PG DLSV St. Louis vs. Tampa Bay, played in Tampa for

Sleep 30 min

Tuesday 9:10 PM

Surround English

HD 1080i Standard

GUIDE MENU INFO BACK

ACTIVITY

About Channel Numbers

Channel Numbers for Over-the-Air Reception or

Reception by Direct Cable

Note: All signals are automatically converted to

1080p for display.

Standard-Definition Analog Channels

Cable 3

480i Stretch

Receiving Standard-Definition

Analog Signal (480i)

Cable Reception Channel 3

Standard-Definition Digital Channels

Ant 7-1 KABC-SD

SD 4:3 Stretch

Receiving Standard-Definition

Digital Signal (SD)

Over-the-Air

Antenna

Reception

Main Channel 7

Sub-Channel 1

High-Definition Digital Channels

Ant 7-1 KABC-HD

HD 16:9 Stretch

Receiving High-Definition

Digital Signal (HD)

Over-the-Air

Antenna

Reception

Main Channel 7

Sub-Channel 1

28 3. Using TV Features

In Canada call 1(800) 450-6487 for assistance.

TV Signals and Display Formats

Signal Definitions

480i: Older type of interlaced signals from the

ANT

input,

composite

VIDEO

, component

Y Pb Pr

, or

HDMI

jacks.

480p: Progressive-scan DVD signals on component

Y Pb

HDMI

jacks.

720p and 1080i: High-definition signals received through

component

Y Pb Pr

HDMI

jacks. These signals are

always 16:9 (widescreen).

1080p: High-definition signals from a PC or Blu-ray player,

HDMI inputs only.

SD 4:3: Standard-definition squarish-screen-format

signals from digital channels on the

ANT

input.

SD 16:9: Standard-definition widescreen-format signals

from digital channels on the

ANT

input.

HD 16:9: High-definition 16:9 widescreen signals from

digital channels on the

ANT

input.

This is a 16:9 widescreen TV suitable for images available

from HDTV and many DVDs. You can view older-style, squar-

ish images (4:3 aspect ratio) using one of the display formats

described on this page. Press the

key and then the

key (

FORMAT

) to cycle through available display formats.

The TV remembers the format you last used for each input.

DVD Image Definitions

Image information may be stated on the DVD case. Some

DVDs support both of the formats described below.

Anamorphic (or Enhanced for WideScreen TV)

Indicates DVDs recorded to show widescreen images prop-

erly on 16:9 TV sets using the TV’s Standard format mode

(recommended)

Non-Anamorphic (or 4:3, 1.33:1, Letter Box, or

Full Screen)

Indicates DVDs recorded for viewing on squarish TV

screens. They may be full screen (4:3 or 1.33:1) which

crops movies to fit the narrow TV, or letter box, which

adds black top and bottom bars.

TV Display Format Definitions

Standard: The full-screen format used by HDTV signals.

Use this format to display anamorphic DVDs with a 1.78:1 or

1.85:1 aspect ratio. Anamorphic DVDs with a 2.35:1 aspect

ratio are displayed correctly but with top and bottom black

bars. Squarish (4:3) images are stretched evenly from side to

side. Available for all signals.

Expand: Enlarges the picture to fill the screen by cropping

the top and bottom; useful for reducing the letter box top and

bottom bars of non-anamorphic DVD images.

Zoom: Enlarges the picture to fill the screen by cropping the

sides, top, and bottom to eliminate black bars.

480i/480p and SD 4:3 signals:• Eliminates top and bottom

bars on anamorphic DVDs with a 2.35:1 aspect ratio.

720p, 1080i, SD 16:9, and HD signals:• Eliminates bars

added to squarish 4:3 images.

Stretch: Stretches a squarish 4:3 image across the

screen to display the entire image with less distortion

than the Standard format.

Stretch Plus:

Similar to Stretch, but minimizes distortion

on the sides by expanding the picture to crop off portions

of the top and bottom. Use to adjust the vertical

position of the picture. L75-A91. Position adjustment may

be unavailable if your NetCommand setup reassigned the

keys for the current device.

Narrow: Displays narrow 4:3 images in their original

shape. Adds black side bars to fill the screen.

Wide Expand: Enlarges the picture, cropping the image on

both sides. Removes or reduces black side bars added to

narrow images converted to 16:9 signals for digital broad-

cast.

Note: All high-definition channels send widescreen

(16:9) signals, but not all programming was created for

the widescreen format. The broadcaster may stretch the

image or add side bars to fill the widescreen area.

Non-anamorphic or SD 4:3

Anamorphic DVD

Standard

Distorted.

Not recom-

mended.

Recommended

Expand

Recom-

mended for

letterbox. See

Note 1.

Distorted; not

recommended.

See Note 1.

Zoom

Distorted.

Not recom-

mended. See

Note 1.

Recommended

for anamorphic

2.35:1 images.

See Note 1.

Stretch

Recom-

mended for

standard

broadcasts.

See Note 1.

Distorted; not

recommended.

See Note 1.

Stretch

Plus

Recom-

mended for

standard

broadcasts.

See Note 1.

Distorted; not

recommended.

See Note 1.

Narrow

See Note 1 Distorted; not

recommended.

See Note 1.

Note 1: Available for 480i, 480p, and digital SD 4:3 signals only.

Original Signal Display Formats

SD 16:9 or

HD Digital

720p, 1080i,

1080p Signal

Wide

Expand

Recommended to re-

move side bars.

Zoom

Recommended to re-

move bars from the top,

bottom, and sides.

TV Display Formats. Press the

key and then

repeatedly press the

key (

FORMAT

)

to see the displays

available for the current program. Press the

INFO

key to

see the name of the display format in use.

Original

Signal

Display

30 3. Using TV Features

In Canada call 1(800) 450-6487 for assistance.

3D Video, continued

3D Safety Requirements

3D Glasses are NOT designed as sunglasses or safety glasses and do not provide protection. 3D glasses should •

be worn only when viewing 3D material.

Do not wear the wireless glasses in any situations that require unimpaired visual perception.•

Children under the age of 5 should not view 3D programming.•

Under normal conditions, 3D viewing is safe for your movies or games. Some people may experience discomfort,

however. To minimize the potential for experiencing visual problems or any adverse symptoms:

Read and follow any and all safety warnings that accompany your 3D glasses or 3D source devices.•

Maintain a distance of no less than 2 to 2.5 times the screen height measurement away from the display. Viewing •

from too short a distance can strain your eyes.

Take regular breaks, at least 5 minutes after every hour of 3D viewing.•

If you experience any of the following symptoms, discontinue 3D viewing until the symptoms go away:

nausea, dizziness, or queasiness, •

headache, or eyestrain, •

blurry vision,•

double vision that lasts longer than a few seconds,•

Do not engage in any potentially hazardous activity (for example, driving a vehicle) until your symptoms have com-

pletely gone away. If symptoms persist, discontinue use and do not resume 3D viewing without discussing your

symptoms with a physician.

Do not use the glasses where loss of balance or limiting your field of vision may be dangerous to you.

Do not use near staircases, ledges or balconies. You may risk falling during or after use.

Epilepsy

WARNING!

IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY, CONSULT A PHYSICIAN BEFORE

USING COMPUTER GAME PRODUCTS.

A small percentage of the population may experience epileptic seizures when viewing certain types of TV images or

video games that contain flashing patterns of light.

The following people should consult a physician before viewing 3D Games or Video:

Anyone with a history of epilepsy, or who has a family member with a history of epilepsy•

Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects.•

WARNING!

SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY.

DISCONTINUE 3D VIEWING IF YOU EXPERIENCE ANY OF THE FOLLOWING SYMPTOMS:

Involuntary movements, eye or muscle twitching•

Muscle cramps•

Nausea, dizziness, or queasiness•

Convulsions•

Disorientation, confusion, or loss of awareness of your surroundings•

Do not engage in any potentially hazardous activity (for example, driving a vehicle) until your symptoms have com-

pletely gone away.

Do not resume 3D viewing without discussing the symptoms with your physician.

Notice Concerning Format Compatibility

In order to display 3D images. Mitsubishi 3D Ready DLP

Home Cinema TVs require the use of a 3D source device

coupled with the Mitsubishi 3D adapter or other source

devices that support checkerboard display formats for

display of 3D games, 3D broadcasts from terrestrial/cable/

satellite and 3D Blu-ray disc content. In all cases an emitter

and matching 3D active shutter glasses or DLP Link active

shutter glasses are required in order to view 3D content.

3. Using TV Features 31

In the U.S. call 1(877) 675-2224 for assistance.

The USB Media Player Menu

Displaying the Menu

Back up the data on your USB drive before con-

necting it to the TV. Mitsubishi is not responsible

for any file damage or data loss.

Connect your USB drive to the TV’s USB port.

The USB Media Player menu displays while files

are being read. Wait until icons appear in the menu

before continuing.

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

IMPORTANT

Do not use USBa for this purpose.

The TV is unable to read files from

the USBa port.

From the USB Menu you can:

Activate any of the

menu options

Highlight an icon and press

ENTER

Display the Activity

menu.

Press

ACTIVITY

Press again to

clear.

Display the main

menu.

Press

MENU.

Press again to

clear.

Display status for the

USB device.

Press

INFO.

Press

BACK

clear.

To resume use of the USB port after switching the

TV to a different input, press

ACTIVITY

, choose View

Photos, and select the USB icon port.

Playing a Slide Show or Playlist

Use these keys while playing a slide show or playlist.

ENTER

Replays the slide show or playlist.

Pauses a slide show or playlist.

Stops a slide show or playlist.

Displays the previous or next slide.

Plays the previous or next track.

GUIDE

Rotates an image clockwise in 90˚ incre-

ments.

BACK

Displays the USB Media Player menu.

Displays the main menu and stops play.

ACTIVITY

Displays the Activity menu and stops play.

INFO

Displays slide name or track name. Press

BACK

to clear.

IMPORTANT

Always stop playback with (

STOP

) or change

to a different TV input before disconnecting your

USB device.

The TV can read photo or music files from a USB •

device. Photos must be in JPEG format and music

files must be in mp3 format. To play music files

while displaying a photo slide show, see “USB

Media Setup Menu” on the next page.

The TV can display still or moving images from a •

camera through the

Y/VIDEO

port. See “Photos

and Moving Video as Composite Video,” page 33.

Camera and Music Files

The TV can read JPEG files as created by the

camera. If you edit a picture file on a computer

and resave the image, the TV may be unable to

read the resaved file.

32 3. Using TV Features

In Canada call 1(800) 450-6487 for assistance.

Thumbnail and Playlist

Menus

JPEG Thumbnail Menu

Use these keys while viewing JPEG thumbnail images

or the music tracks in a playlist.

Moves the highlight from item to item.

GUIDE

Rotates a thumbnail clockwise in 90˚

increments

ENTER

Plays the slide show or playlist starting

with the highlighted item.

Selects the last item on the current page.

Selects the first item on the current page.

PAGE UP/DN

Displays the next or previous page of

items.

BACK

Displays the USB Media Player menu.

Displays the main menu.

ACTIVITY

Displays the Activity menu.

Notes on Using the USB Port

• TheTVignoresallcommandswhilereadingfiles.

Wait

until the Play icon appears highlighted and in full

color before continuing.

• Largefilesorhigh-capacitystoragedevicesmaytakea

long time to display.

•

The TV can read files up to 10 MB in size with a

maximum of 2,500 files stored on the device. The

FAT16 or FAT32 file system is recommended.

• UseaUSBdriveinsteadofacardreader.

• BackupthedataonyourUSBdrivebeforecon-

necting it to the TV. Mitsubishi is not responsible

for any file damage or data loss.

Note:

Some manufacturers’ USB devices may be incom-

patible with the TV. If the TV is unable to display

your photos, you can:

• Transfer

files to a different USB device.

• Useyourdigitalcamera’scompositevideo

output. See page 33.

Picture Files Compatible with the USB Port

• Stillimagesrecordedondigitalcamerasusingthe

Exchangeable Image File Format, version 2.1 (EXIF

2.1) standard for digital still cameras and Design

Rules for Camera File Systems version 1.0 (DCF 1.0)

• Someimagesopenedandresavedonacomputer

may not play back or may not display in the thumb-

nail list. This happens if the files were resaved in an

incompatible format.

• Fullpathfilenamescanbenolongerthan50char-

acters and must end in a .jpg extension. Only the

first 20 of the 50 characters will display.

Camera and Music Files, continued

USB Media Setup Menu

Use the USB Media Setup menu set up play of a slide

show or playlist.

• IfJPEGimagefilesandmp3filesareontheUSB

device, choose:

Slideshow + Music -

Slideshow -

Music only -

Slideshow.• Select either Auto or Manual advance

for the slide show. During manual operation, press

ENTER

to advance to the next slide.

Interval.• For automatic advance, select the time

interval for display of each slide. The interval you

select here is the minimum time between slides;

actual time may be longer for larger files.

Frequency.•

For automatic advance, select the

number of times (frequency) to play the complete slide

show and/or playlist:

Once, Twice, or Continuous.

Press •

BACK

to close the Media Setup menu and

return to the Media Player menu.

34 3. Using TV Features

In Canada call 1(800) 450-6487 for assistance.

Streaming Internet Movies with VUDU

L75-A91. This TV’s built-in VUDU™ capabilities allow

you to access your own personal home video store

right on your TV. VUDU’s service offers you:

The largest on-demand HD movie selection any-•

where, featuring full 1080p and 5.1 surround sound.

All of Hollywood’s latest hits and classics. Movies •

are available to rent or buy the same day the movie

comes out on DVD.

VUDU allows you to enjoy movies with no store •

visits, no mailing, no late fees and no subscriptions.

Parental controls allow you to restrict access to •

content according to MPAA ratings. See the VUDU

Info & Settings menu.

VUDU features popular internet applications provid-•

ing free content.

At the time of this writing, VUDU requires an internet

bandwidth of 4.0 Mbps or higher for instant HD video

and 2.0 Mbps or higher for instant SD video. These

specifications are subject to change. Visit www.VUDU.

com to learn more about available titles, prices, recom-

mended bandwidth, and services offered. For a list of

recommended routers and switches, see the Support >

FAQ section at VUDU.com.

Required for VUDU Service

Broadband internet service•

Ethernet cable • or the VUDU wireless kit.

Computer access to the VUDU.com website •

(required for one-time account activation).

A credit card for rental and purchase transactions.•

Standard Connection

Connect the TV to your network router or directly to a

high-speed internet modem using an Ethernet cable

(not supplied).

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

DVI/PC L

INPUT

Pb Pr

Y/ VIDEO

Ethernet

cable

Internet

router or

modem

Incoming

high-speed

internet

service

Standard VUDU connection via Ethernet

VUDU Wireless Kit

The VUDU wireless kit is available for purchase from

VUDU.com. The kit includes the two wireless boxes,

two power cables, and two Ethernet cables shown in

the diagram below. VUDU capabilities are built right

into the TV, so connect VUDU Wireless Box 2 directly

to the TV as shown.

The LED indicators for •

POWER

and

ETHERNET

will

light up once power is applied to the boxes.

After a few seconds, the LED indicator for •

WIRELESS

will start to blink, indicating the wireless

adapters have been set up successfully.

The LED indicators for •

WIRELESS

and

ETHERNET

will blink when data is being transmitted.

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

USB-to-DC

power cable

AC-to-DC

power

cable

VUDU Wire-

less Box 2

Router

or modem

Ethernet

cable

Ethernet

cable

VUDU Wire-

less Box 1

Connecting the VUDU wireless kit. Connect VUDU

Wireless Box 2 directly to the TV.

In the U.S. call 1(877) 675-2224 for assistance.

4TV Menus

Displays or clears the main menu.

Moves up one menu level.•

Clears the current menu.•

Moves navigation into options •

area.

Selects an item.•

Moves the highlight within menus.

Makes adjustments in some

menus.

Look for the key guide at

the bottom of each menu.

Main Menu

Press

on the remote control to open the main menu and then select from one of these categories.

Adjust Customize picture and sound settings; enable 3D mode. 38

Captions Turn closed captions on and off; customize caption displays. 42

Initial Perform basic TV setup. Set language, scan (memorize) channels and edit

channel options, set the TV clock, set auto-on TV Timer. 43

Input Assign names to TV inputs, enable HDMI Control, assign activities to inputs.

Model L75-A91. Perform NetCommand IR “learning.” 45

Lock Restrict TV use. Disable the control-panel buttons. Set a pass code. 47

Menu Navigation

38 4. TV Menus

In Canada call 1(800) 450-6487 for assistance.

Picture

Mode

Super

Brilliant

The Super Brilliant Picture Mode is designed to compensate for the

harsh, bright lighting used in retail settings and is not recommended for

home use. Prolonged use of the Super Brilliant Picture Mode will age

the lasers faster, reducing picture brightness as the TV ages.

Set the Picture Mode

first before changing

Categories

D Sexual Dialog. Applies in differing degrees to TV-PG and TV-14.

Adult Language. A

pplies in differing degrees to TV-PG, TV-14, and TV-MA.

Sexual Situations. Applies in differing degrees to TV-PG, TV-14, and TV-MA.

VViolence (graphic or realistic). Applies in differing degrees to TV-PG,

TV-14, and TV-MA.

Movie

Rating

G General Audience. Designed for the entire family.

Parental Guidance. Parental Guidance recommended; may not be suitable for some children.

PG-13 Parental Guidance, 13 and Older. Not recommended for children under 13.

Restricted. Restricted in theaters to 17 years old and older unless accompanied by an adult.

NC-17 No Children 17 or Under. Restricted in theaters to 18 years old and older.

XAdult. Designed for and restricted in theaters to adult audiences only.

Not Rated No MPAA rating assigned

4. TV Menus 49

In the U.S. call 1(877) 675-2224 for assistance.

Lock, continued

Time

Blocks all use of the TV during the time period you specify. You must enter a pass code to use the

TV when the time lock is in effect.

Lock by Time

Enables/disables Lock by Time.

Lock Time,

Unlock Time

To set the lock and unlock times:

Highlight the hour digits for the 1. Lock Time.

Press 2. repeatedly to change the hour and associated AM/PM indicator. To

move quickly through the numbers, just press and hold.

Press 3.

ENTER

to set the hour and highlight the minutes.

With the minutes highlighted, press 4. repeatedly to change the minutes. To

move quickly through the numbers, just press and hold.

Highlight the 5. Unlock Time digits and set the time as described above.

Note: T

o make Lock by Time active 24 hours a day, make Start Time and Stop Time

the same.

Panel

Off, On On locks and Off unlocks the buttons on the TV’s control panel. Use this option if

small children try to press TV buttons.

To • release the Panel Lock from the TV’s control panel, press and hold the

ACTIVITY

button for ten seconds. If the TV is powered off, press

POWER

after the

lock releases to make the TV power on.

To reactivate the lock, return to this menu and change the setting to • On.

Other

Other Menu Options (alternate rating system)

Model L75-A91, U.S. Only

This TV can recognize new rating systems that may come into effect in the future. The Other option

remains grayed out until the TV receives a signal using an alternate rating system. Such alternate

rating systems will apply only to digital programming received on the

ANT

input.

Lock On, Off Enables/disables program blocking.

System Name

The rating system available for the channel

Group Rating groups available in the rating system shown on the screen. Rating groups are

defined by the rating system in effect.

Rating Rating restrictions available in the selected rating system and group. Highlight the

rating and press

ENTER

to check (block) or uncheck (allow) rated content.

In Canada call 1(800) 450-6487 for assistance.

NetCommand IR Control

NetCommand IR home-theater control is avail-•

able on model L75-A91.

NetCommand IR home-theater control setup is •

optional.

You can perform NetCommand setup when the TV •

first recognizes a device during Auto Input Sensing

or at any convenient time afterward.

NetCommand operates by sending remote control •

signals from the TV to your other devices via the

IR (infrared) emitters, telling the devices to play,

record, change inputs, adjust volume, change

channels, or perform other functions. All this is

accomplished with the TV’s remote control left in

mode.

You may wish to use NetCommand IR control to •

supplement control of CEC-enabled devices.

Important Note on NetCommand

Be sure to connect the IR emitter cable to the

TV and properly place the emitters so that

NetCommand can control your devices.

About NetCommand IR Control

5. NetCommand IR Control 51

In the U.S. call 1(877) 675-2224 for assistance.

The NetCommand system uses emitters connected

to the

–

NetCommand Output

jack to control other

devices such as DVD players, cable boxes, satellite

receivers, and VCRs.

Replacement IR emitter cables are available for

purchase from Mitsubishi. Request either part

number 242D483020 (two-ended cable) or part number

299P254020 (four-ended cable).

Connect the plug end of the IR emitter cable to the

IR—NetCommand Output

jack on the TV back panel.

When the

New Device Found screen displays,

leave

IR—NetCommand Output selected.

Highlight

EXIT and press

ENTER

The New Device Found screen displays when you

connect the IR emitter cable.

Position the emitter end with the emitter bulb facing

the device’s remote control sensor. The bulb emits

infrared light in a cone-shaped pattern. Place the

bulb far enough from the sensor to allow the cone

pattern to reach the sensor.

In some cases, the emitter works better facing

downward from the top of the device. Experiment

to find what works best.

Secure the emitter ends in place using double-

sided tape.

Place any unused ends behind the devices to

prevent stray signals from reaching the IR sensors.

DIGITAL

SURROUND

A/V Receiver

Other A/V Device

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

IR-NetCommand

Output/External

Controller Input

IR-

NetCommand

Output/External

Controller Input

Connecting IR–NetCommand Output

In front of a

single average-

sized device

On top of a single

tall device

In front, shared

by two average-

sized devices

IR sensor

In front of a single

average-sized device

On top of a single tall

device

In front, shared by two

average-sized devices

IR sensor

In front of a single

average-sized device

On top of a single

tall device

In front, shared by

two average-sized

devices

IR sensor

Place IR emitters so the signal can be “seen” by the IR

sensor on each device.

If You are Unable to Locate

a Device’s IR Sensor

The IR sensor is usually behind the plastic window •

of the front display panel. Using a flashlight, you

may be able to see it as a round or square cutout.

If you cannot see the sensor and the device’s •

Owner’s Guide does not specify the location, do

the following using the device’s remote control.

Starting at one end of the plastic window, hold 1.

the device’s remote control about one-half

inch from the front of the device and press the

POWER

key.

If the device does not respond, move the 2.

remote control one inch toward the center and

try again. Repeat until the device responds.

Repeat the previous steps starting at the other 3.

end of the window. The sensor will be between

these two points.

IMPORTANT

Position IR emitters so that each device’s

sensor “sees” the signal from only one emitter.

Otherwise, a device receiving signals from

multiple sources (remote controls, IR emitters)

may not respond at all.

IR Emitter Placement

52 5. NetCommand IR Control

In Canada call 1(800) 450-6487 for assistance.

To perform this procedure, you need:

The remote controls for both the TV and the •

device you want to control.

An IR emitter cable (included)•

Note: To set up an A/V receiver, see “Setting Up A/V

Receiver Control,” page 57.

Connect and position the IR emitters for the

devices you wish to control. See “IR Emitter Place-

ment” on the previous page.

Set the

TV’s remote control to

mode and power

on the TV.

Open the NetCommand

Learn screen as follows:

If working from the • New Device Found screen

after the device is first detected, highlight

NetCommand and press

ENTER

to open the

Learn screen for the device.

If performing NetCommand setup at any time •

after the device has been recognized through

Auto Input Sensing:

a. Press

ACTIVITY.

b. Highlight the desired input icon and press

ENTER

to switch to that input.

c. Press

, highlight Inputs, and highlight

Learn to open the Inputs > Learn screen

for the device.

The first function highlighted in the

Learn screen

is always Power On. Aim the TV’s remote control

at the TV and press

ENTER

to begin learning for that

function.

When the

Power On

text starts flashing, aim the

device’s

remote control at the TV and hold the

POWER

key until a check mark appears next to Power On.

If the text stops flashing before the check mark •

appears, repeat the previous step.

To remove the key from NetCommand control, •

press the

CANCEL

key while the key name is

highlighted.

Press the

keys on the TV’s remote control

to highlight other keys on the list. Repeat steps

4 and 5 for each additional function you wish to

control through NetCommand.

Note: Device keys in the far right column will be asso-

ciated with the remote control’s

key when

“learned.” See the table on page 54.

If the device has a separate

POWER OFF

key, press

on the TV’s remote to highlight Power Off.

Repeat the earlier steps to “learn” the

POWER OFF

key.

If the device has no

POWER OFF

key, skip this step.

Press

BACK

to finish NetCommand “learning” for the

current device.

From the New Device Found screen, highlight

NetCommand and press ENTER to open the Learn

screen.

Initial NetCommand Setup

Inputs > Learn screen

Key names marked with a

check have been “learned.”

Device-specific keys in the

rightmost column can be accessed

with the MORE key after “learning.”

Adding or Removing Device Keys from

NetCommand Control

Switch the TV to the device. Press

ACTIVITY

, high-

light the device’s icon, and press

ENTER

Open the

Inputs menu and highlight the Learn icon.

When the

Learn screen displays:

To add keys: • Continue as described earlier

under “Initial NetCommand Setup” on this

page.

To delete keys:• Highlight the name of the key

you wish to delete and press

CANCEL

on the

TV‘s remote control to clear the check mark.

54 5. NetCommand IR Control

In Canada call 1(800) 450-6487 for assistance.

Key Name in

Learning Screen

Special Operation Description and Setup How to Use

Enter ENTER-Key Functions (cable boxes, satellite receivers, etc.)

Some devices have two keys that have “enter” functions. One key is for menus and is often labelled

SELECT

. A second key is for use with number keys for direct channel selection. NetCommand

uses the same

ENTER

key for both operations.

When

ENTER

has a menu or guide function or

when the original remote control uses the same

key for menus and channel selection:

Learn the

ENTER

SELECT,

key in the

NetCommand Enter learning position.

Press 1.

GUIDE

to display the device’s

menu or guide.

Press 2.

ENTER

within the menu and

NetCommand will send the Enter signal for

menus.

Enter (digits)

When

ENTER

is for channel changes, i.e., the origi-

nal remote control has a separate

ENTER

key for

this function):

Learn the

ENTER

key for channel selection in

the NetCommand Enter (digits) learning posi-

tion. Use this learning position only if the original

remote control has separate keys for Enter in

menus and Enter for channel selection.

Press digit key(s) and then press

ENTER

NetCommand will send the Enter signal for

channel selection.

Cancel CANCEL as the Cancel or Exit Function

“Learn” the Cancel or Exit function in the

NetCommand Cancel learning position

Press 1.

GUIDE

to display the menu or

guide.

Press 2.

CANCEL

and NetCommand will send

the Cancel or Exit signal.

—

(separator)

The symbol “—” can serve as the separator

between a digital channel’s main and sub-channel

digits, e.g., digital channel 12-1 (main channel is

12, sub-channel is 1).

“Learn” the channel separator function in the

NetCommand – (separator) learning position.

Press digit key(s) and press

CANCEL

NetCommand will send the channel-separator

signal.

The MORE Key Menu and NetCommand

Perform NetCommand setup for these device-specific

keys and then access their functions with the

key.

Device

Key

VCR

Cable/

SAT

DVD/

DVR

A/V

Receiver

Input

SP/EP

List

On Demand

Device

Key

VCR

Cable/

SAT

DVD/

DVR

A/V

Receiver

Top Menu

Angle

Audio (DVD)

Subtitle

Repeat

Bonus View

Setup

Surround

Night

Operating NetCommand-Controlled Devices, continued

5. NetCommand IR Control 55

In the U.S. call 1(877) 675-2224 for assistance.

NetCommand Specialized Device Keys

Refer to this chart when “learning” device keys. “Learn”

some, all, or none of the keys used for each device

type.

See page 53 for more on keys marked in the “Special

Operation Method” column.

Key Name in

Learning Screen Function Name on TV

Remote Control

See Special

Operation

Method Table

Power On Power On or Power ON/OFF (toggle) 

Guide On-Screen Program Guide or DVD Disc Menus 

Channel +/Skip + Next Channel Higher/

Skip Forward (Disc)

Channel –/Skip – Next Channel Lower/

Skip Backward (Disc)

Page Up Page Up in Guides

Page Dn Page Down in Guides

Up Arrow up

Down Arrow down

Left Arrow left

Right Arrow right

Enter Enter or Select (menus) 

Cancel Cancel or erase (menus) 

Play Start playback

Stop Stop playback

Forward Fast Forward

Rewind Rewind/Fast Reverse

Pause Pause playback

Record Start Recording

1, 2, 3, 4, 5, 6, 7, 8, 9, 0 Digits

1, 2, 3, 4, 5, 6, 7, 8, 9, 0

Enter (digits) Use after entering digits to tune directly to a

channel by number 

- (separator) Add digital channel separator between main

channel number and sub-channel number 

Last Last Channel Recall

Info On-screen status display or information display May require two

keypresses

Power Off Power Off 

Operating NetCommand-Controlled Devices, continued

6. NetCommand Control of an A/V Receiver 57

In the U.S. call 1(877) 675-2224 for assistance.

IMPORTANT

To hear audio sent from the TV to the A/V receiver,

you must have:

Physically connected the TV to the A/V •

receiver. Connection can be via the analog or

digital audio output or over HDMI.

Assigned the name AVR if using an HDMI A/V •

receiver that was not recognized automatically.

“•

Learned” the IR codes for the A/V receiver

inputs.

Assigned the TV’s audio output to the correct •

input in the NetCommand Inputs > AVR menu.

Selected the A/V receiver as the audio source. •

Press MORE then 9 (AUDIO), then

to show

the Speakers option,

then

to select the A/V

Receiver.

Setting Up A/V Receiver Control

Power and Volume

Perform this setup to control the A/V receiver power

and volume with the TV’s remote control.

To perform this setup you need:

The remote controls for both the TV and the •

A/V receiver.

An IR emitter cable (included).•

Before You Begin

Connect your A/V receiver to the TV and any addi-

tional devices. See “Setting Up TV Inputs,” page 12

and “TV Connections,” page 18.

Connect the IR emitter cable to the TV and position

the IR emitter where it can send signals to the A/V

receiver. See “IR Emitter Placement,” page 51.

Set the

TV’s remote control to

mode using the

side button.

Setup to Control A/V Receiver Power and Volume

Open the

Inputs > AVR screen in one of two ways:

If using the • New Device Found screen for the

A/V receiver, highlight NetCommand and press

ENTER

to open the AVR screen.

If performing NetCommand setup at any time •

after Auto Sensing:

Press

, highlight Inputs, and highlight AVR

to open the AVR menu.

The first function highlighted in the

AVR screen is

always Power. Aim the TV’s remote control at the

TV and press

ENTER

to begin learning for Power.

Inputs > AVR screen. Perform

NetCommand IR “learning” for A/V

receiver power and volume keys.

When the

Power text starts flashing, aim the A/V

receiver’s remote control at the TV and hold the

POWER

POWER ON

key until a check mark appears

next to Power.

If the text stops flashing before the check mark •

appears, repeat this step.

To remove the key from NetCommand control, •

press the

CANCEL

key while the key name is

highlighted.

Press the 4. key on the TV’s remote control to highlight

other keys in the list. Repeat steps 2 and 3 for each addi-

tional function you wish to control through NetCommand.

If the A/V receiver has a separate

POWER OFF

key,

press on the TV’s remote to highlight Power Off.

Repeat steps 2 and 3 to “learn” the

POWER OFF

key.

If the device has no

POWER OFF

key, skip this step.

When finished “learning” the power and volume

keys, either

To watch TV, press •

BACK

To continue with NetCommand setup to control •

switching of A/V receiver inputs, highlight

NEXT and press

ENTER

58 6. NetCommand Control of an A/V Receiver

In Canada call 1(800) 450-6487 for assistance.

Automatic Audio or Audio/Video Switching

The following setups enable the A/V receiver to switch

automatically to the correct input when you select a

device in the TV’s Activity menu.

Three different connection arrangements are described

here. Review the descriptions to find the setup needed

for your equipment.

To hear digital surround sound from a source device

you must use the setup described for Cases 2 or 3

To set up control of an A/V receiver you need:

The remote controls for the TV and A/V receiver.•

An IR emitter cable available from Mitsubishi.•

Connecting cables•

Before You Begin

Connect your A/V devices to the TV and connect

your A/V receiver to the audio outputs on the TV

and the DVD player. Note the name of the device

connected to each A/V receiver input. See initial

setup, page 12, and “TV Connections,” page 18.

Position NetCommand IR emitters as described in

“IR Emitter Placement,” page 51.

Set the TV’s remote control to

mode using the

side button.

Open the

Inputs > AVR menu, highlight NEXT

and press

ENTER

to display the device-key-learning

menu.

Case 1: Automatic A/V Receiver

Switching to the TV Audio Input

Most devices are set up to use the TV’s audio output like

the VCR in this example; analog audio from the device is

sent through the TV to the A/V receiver’s TV audio input.

Use this setup for:

Audio Available from TV only. • Send audio from

the

ANT

input to the A/V receiver from the TV’s

analog or digital audio output.

Use this setup to make the A/V receiver switch to its

designated TV audio input when viewing programming

from the

ANT

input.

Analog Stereo Audio. •

Audio from sources with only

analog stereo output (such as a VCR) can be sent either

directly to the A/V receiver or through the TV first.

Mitsubishi recommends you send audio through the

TV as shown in the example. The TV converts analog

audio to digital format to send to a digital A/V receiver.

HDMI Digital Stereo Audio. • Digital stereo audio

from an HDMI connection is available both in digital

and analog format from the TV’s analog and digital

audio output jacks.

Setting Up A/V Receiver Control, continued

audio + video

Incoming Coaxial Cable

to TV’s ANT input

A/V Receiver

DVD audio

input

TV audio input

TV audio

out

audio output from

TV (digital or analog)

video

analog audio

VCR with

Analog Audio Output

Important:

To use this setup, you must connect the TV’s

audio output to the A/V receiver’s TV audio input jack.

In the

Inputs > AVR > NEXT menu, press to

highlight TV audio out as the A/V receiver input to

control.

Press

ENTER

on the TV’s remote control.

While the text

TV audio out is flashing, press and

hold the

TV INPUT

key on the A/V receiver’s remote

control.

When a check appears next to

TV audio out,

release the

TV INPUT

key.

If the text stops flashing before the check mark •

appears, repeat this step.

To erase the IR code just “learned,” press •

CANCEL

while the name is highlighted.

Press

if finished or continue with Case 2 setup

if you want to control surround sound switching for

another audio source.

Case 1: NetCommand setup for controlling A/V

receiver switching to the A/V receiver’s audio input

from the TV

The list displayed represents inputs in use.

The device names are those you assigned in the New

Device Found screen or in the Inputs > Name menu.

IMPORTANT

All audio from what you are watching on the TV is

always available from both the TV’s AVR AUDIO

OUTPUT and DIGITAL AUDIO OUTPUT jacks.

To use the digital surround sound capabilities of your

A/V receiver however, you must connect the audio

output from your DVD player, satellite receiver, or cable

box directly to the A/V receiver.

6. NetCommand Control of an A/V Receiver 59

In the U.S. call 1(877) 675-2224 for assistance.

Setting Up A/V Receiver Control, continued

Case 2: Automatic A/V Receiver Switching

to a Surround Sound Device

Note: Use this setup to send digital surround sound

from a source device directly to your external sound

system. For non-surround sound source devices,

Mitsubishi recommends using the setup for Case 1,

in which audio is sent through the TV.

A device can send digital surround sound such as Dolby

Digital or DTS directly to the A/V receiver. The device might

be a DVD player, cable box, or satellite receiver, and could

have HDMI output. A DVD player is used in this example.

Your setup may include additional devices with digital

surround sound connected directly to the A/V receiver.

These devices might be a DVD player plus a cable box

or satellite receiver. Inputs already connected to the TV

will appear listed in the setup screen.

audio + video

Incoming

Coaxial

Cable

A/V Receiver

DVD audio

input

DVD Player with

Digital Surround Sound

video

digital surround sound

video

analog audio

DVD Player

with

Digital

Surround

Sound

Case 2: A/V receiver audio from a device providing

surround sound directly to the A/V receiver

In the

Inputs > AVR > NEXT menu, press

to highlight the name of the A/V receiver input to

control. In this example, it is the DVD input.

Press

ENTER

on the TV’s remote control.

Case 2: NetCommand setup for

controlling A/V receiver switching

to the A/V receiver’s DVD input. The list contains

connected inputs with names assigned during Auto

Input Sensing.

While the text

DVD is flashing, press and hold the

DVD INPUT

key on the A/V receiver’s remote control.

When a check appears next to

DVD, release the

DVD INPUT

key.

If the text stops flashing before the check mark •

appears, repeat this step.

To erase the IR code just “learned,” press •

CANCEL

while the name is highlighted.

If finished, highlight

EXIT and press

ENTER

continue to set up additional A/V receiver audio

sources.

Combining Setup Types

Your setup can include devices connected

using the Case 1 method plus other devices

connected using the Case 2 method.

60 6. NetCommand Control of an A/V Receiver

In Canada call 1(800) 450-6487 for assistance.

Case 3: Automatic Audio and

Video Switching via HDMI

If your A/V receiver has an HDMI output, it may be

convenient to route video signals from multiple devices

over a single cable to the TV. Use this procedure to set

up NetCommand control of the A/V receiver’s audio

and video switching over a single HDMI cable. The

connected source devices can be analog, digital, or a

mixture or the two. When this setup is complete, you

can use the TV’s Activity menu to select a video device

connected to the A/V receiver.

VCR with

Analog Audio Output

A/V Receiver

HDMI

Output

digital surround sound

HDMI Cable

Blu-ray player

DVD player

Cable box

VCR

More About Using an HDMI Connection

Audio from devices connected directly to the TV can •

be heard from the TV speakers only. To send audio

to the A/V receiver from such devices, use one of the

optional audio connections shown in the diagram on

this page. For example, use an optional audio con-

nection if you wish to use the A/V receiver speakers to

hear audio from:

The - ANT input

A game or camcorder -

To use NetCommand to supplement HDMI control of •

a CEC-enabled A/V receiver, the recommended setup

sequence is:

Connect the HDMI cable.1.

Enable HDMI control (2. New Device Found screen).

Connect the secondary digital audio cable, if 3.

desired.

Perform NetCommand setup.4.

If you connect to HDMI after performing NetCommand

setup for the A/V receiver, the NetCommand setup will

be lost.

In some cases, audio from a device connected to the •

A/V receiver may not be passed over the HDMI cable

to the TV speakers. In these cases you must use the

A/V receiver speakers to hear audio.

Multiple video inputs through a single HDMI cable. You can

connect multiple video devices to an A/V receiver that has

an HDMI output. The optional audio connection allows you

to hear, through the A/V receiver, devices connected to the

TV only, e.g., an antenna on the

ANT

input.

Before You Begin

To complete these steps you will need:

The remote controls for both the TV and the A/V •

receiver.

An IR emitter cable (included)•

An HDMI-to-HDMI cable to connect the A/V •

receiver to the TV and cables necessary to

connect devices to the A/V receiver.

Connect the A/V receiver to the TV with an HDMI-to-

HDMI cable. Do not connect the optional audio cable

at this time.

If desired, enable HDMI Control of a CEC-enabled

A/V receiver. See Appendix C, “HDMI Control of CEC

Devices.”

Connect your audio/video devices to the A/V receiver.

Note the name of the device connected to each A/V

receiver input. This information will be needed later to

set up NetCommand’s automatic input switching.

Setting Up A/V Receiver Control, continued

1 2 3 4

HDMI

AVR AUDIO OUTPUT

DIGITAL

AUDIO

OUTPUT

RS-232C

GLASSES

EMITTER

ANT

INPUT 2

INPUT 1

DVI/PC L

INPUT

IR-

NetCommand

Output/External

Controller Input

Pb Pr

Y/ VIDEO

HDMI

OUT

A/V receiver

with HDMI

output

Any connec-

tion types

(can be HD or

SD video)

AUDIO

DIGITAL

AUDIO IN

VCR

Cable box

DVD player

DIGITAL

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

AVR AUDIO OUTPUT

Optional audio

connection

(analog or digital)

HDMI

cable

6. NetCommand Control of an A/V Receiver 61

In the U.S. call 1(877) 675-2224 for assistance.

If using an optional audio cable between the TV and

A/V receiver, connect it.

Connect the IR emitter cable to the TV and position

the IR emitter where it can send signals to the A/V

receiver. See “IR Emitter Placement,” page 51.

Setup to Control Automatic Audio

and Video Switching via HDMI

When this setup is complete, the “learned” A/V receiver

input will appear in the TV’s Activity menu as a select-

able input.

Power on the A/V receiver.

Set the

TV’s remote control to

mode using the

side button.

Power on the TV.

When the

New Device Found screen displays,

select device name AVR if it is not recognized auto-

matically.

Navigate to the

Inputs > AVR menu or, from

within the New Device Found screen, highlight

NetCommand and press

ENTER

To set up A/V switching over HDMI, choose your

devices from a list. Unlike the device list described for

Case 2, this is a generic list containing more than just

the devices detected in your setup.

In the

Inputs > AVR > NEXT menu, press

to highlight the name of the A/V receiver input to

control. In this example, it is the DVD input.

Press

ENTER

on the TV’s remote control.

While the text

DVD is flashing, press and hold the

DVD INPUT

key on the A/V receiver’s remote control.

When a check appears next to

DVD, release the

DVD INPUT

key.

If the text stops flashing before the check mark •

appears, repeat this step.

To erase the IR code just “learned,” press •

CANCEL

while the name is highlighted.

If there are no more devices to set up, highlight

10.

EXIT and press

ENTER

or continue to set up addi-

tional A/V receiver audio/video sources.

Setting Up A/V Receiver Control, continued

NetCommand Control of a Device Con-

nected to an HDMI A/V Receiver

Use this setup to have NetCommand control a device

sending audio and video through the A/V receiver to the

TV via HDMI.

You must have already completed the procedure under

“Setup to Control Automatic Audio and Video Switching

via HDMI” on this page. That procedure placed an icon

in the Activity menu for the device (input) connected to

the A/V receiver.

HDMI

Cable

Any Connection

Type

Source

Device

A/V

Receiver

Set up NetCommand control of A/V receiver audio/

video switching via HDMI as described on this

page.

Press

BACK

to close any open menus and return to

normal TV viewing.

Press

ACTIVITY

Highlight the icon for the A/V receiver input you

wish to control.

Press

ENTER

to switch the TV to the A/V receiver

and the A/V receiver to the input.

Open the

Inputs > Learn menu.

Perform NetCommand “learning” for the con-

nected )device by following the steps in “Initial

NetCommand Setup,” page 52.

In Canada call 1(800) 450-6487 for assistance.

Specyfikacje produktu

Marka:	Mitsubishi
Kategoria:	Telewizor 3D
Model:	L75-A91 Laservue

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mitsubishi L75-A91 Laservue, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Telewizor 3D Mitsubishi

Mitsubishi L75-A91 Laservue Instrukcja

23 Września 2024

Mitsubishi L75-A94 Laservue Instrukcja

18 Września 2024

Instrukcje Telewizor 3D

Najnowsze instrukcje dla Telewizor 3D

Toshiba 46UL975G Instrukcja

4 Lipca 2024

Toshiba 55YL875G Instrukcja

2 Lipca 2024

Toshiba 40TL966 Instrukcja

1 Lipca 2024

Philips 47PFL4307H Instrukcja

1 Lipca 2024

Toshiba 42WL863G Instrukcja

30 Czerwca 2024

Toshiba 42YL875G Instrukcja

30 Czerwca 2024

LG 50PZ850 Instrukcja

30 Czerwca 2024

Philips 42PFL4307 Instrukcja

30 Czerwca 2024

Philips 40PFL8606 Instrukcja

30 Czerwca 2024

Toshiba 55ZL2G Instrukcja

30 Czerwca 2024