Instrukcja obsługi Minuteman Front Runner FR17115
Minuteman
Maszyna Boenmachine
Front Runner FR17115
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Minuteman Front Runner FR17115 (12 stron) w kategorii Maszyna Boenmachine. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/12
Front Runner Model:
Floor Machines FR17115, FR17220
FR20115, FR20220
FR20115-2S, FR20220-2S
OPERATION SERVICE PARTS CARE
Revised 04/06
FOR COMMERCIAL USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
WARNING - To reduce the risk of fire, electric shock, or injury:
• Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
WARNING
To reduce the risk of electrical shock - Do not expose to rain. Store indoors.
• Never allow children or untrained adults to operate this equipment.
• Keep the area of operation clear of all persons, particularly small children, and pets. Keep bystanders
at least 25 feet away from the area of operation.
• Use only as described in this manual. Use only manufacturer‘s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water, return it to a service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair,
and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn off all controls before unplugging.
• Connect to a properly grounded outlet only. See grounding instructions.
SAVE THESE INSTRUCTIONS
1
INSPECTION
Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly
inspected before shipment, and any damage is the responsibility of the delivery carrier who should be
notified immediately.
WARNING
Read Instruction Manual before operating this piece of equipment.
• To reduce the risk of fire use only commercially available floor cleaners and waxes intended for
machine application.
• Risk of explosion - floor sanding can result in an explosive mixture of fine dust and air. Use floor
sanding machine in a well-ventilated area free from any flame or match.
• Electrical motors and components can cause an explosion when operated near volatile materials and
vapors. Do not use this machine near flammable materials such as solvents, thinners, fuels, grain dust,
etc.
ELECTRICAL - 115 Volt
Model FR17115, FR20115, FR20115-2S
This machine is designed to operate on a standard 15 amp. 120 volt, 60 hz, AC circuit. Voltages below
105 volt AC or above 125 volts AC could cause serious damage to the motor.
ELECTRICAL - 240 Volt
Model FR17220, FR20220, FR20220-2S
This machine is designed to operate on a standard 8.3 amp type L fused 230 volt, 50 hz, AC circuit.
Voltages below 200 volt AC or above 250 volts AC could cause serious damage to the motor.
GROUNDING INSTRUCTIONS
• This floor finishing machine should be grounded while in use to protect the operator from electric shock.
The machine is equipped with a three-conductor cord and a three-prong grounding type attachment
plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord
is the grounding wire. Never connect this wire to other than the grounding blade .
• Floor Finishing Machines Rated Less Than 150 Volts - If the machine is provided with an attachment
plug as shown in Sketch A it is intended for use on a 120-volt (nominal) circuit.
• If a properly grounded receptacle as shown in Sketch A is not available, an adapter as shown in Sketch
C is available and should be installed as shown in Sketch B if the outlet box that houses the receptacle
is grounded. Be sure to fasten the grounding tab with the faceplate screw.
• Floor Finishing Machines Rated More Than 150 Volts - If the machine is provided with an attachment
plug as shown in Sketch D, it is intended for use on a nominal 240 volt circuit. No adapter is available
for this plug.
2
Specyfikacje produktu
| Marka: | Minuteman |
| Kategoria: | Maszyna Boenmachine |
| Model: | Front Runner FR17115 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Minuteman Front Runner FR17115, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Maszyna Boenmachine Minuteman
12 Września 2024
10 Września 2024
Instrukcje Maszyna Boenmachine
- Maszyna Boenmachine Hoover
- Maszyna Boenmachine Tornado
- Maszyna Boenmachine Kogan
- Maszyna Boenmachine Mytee
- Maszyna Boenmachine Onfloor Technologies
Najnowsze instrukcje dla Maszyna Boenmachine
7 Października 2024
7 Października 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
20 Września 2024
15 Września 2024
13 Września 2024
10 Września 2024