Instrukcja obsługi Minox DC 8011

Minox Niesklasyfikowane DC 8011

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Minox DC 8011 (41 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/41
EN-1
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of
the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified
in the manual. If such changes or modifications should be made, you could be required
to stop operation of the equipment.
Notice
If static electricity or electromagnetism causes data transfer to discontinue midway (fail),
restart the application or disconnect and connect the communication cable (USB, etc.)
again.
EN-2
READ THIS FIRST
Trademark Information
Microsoft
®
and Windows
®
are U.S. registered trademarks of Microsoft Corporation.
Pentium® is a registered trademark of Intel Corporation.
Macintosh is a trademark of Apple Computer, Inc.
SD™ is a trademark.
Other names and products may be trademarks or registered trademarks of their
respective owners.
Product Information
Product design and specifications are subject to change without notice. This
includes primary product specifications, software, software drivers, and user’s
manual. This User Manual is a general reference guide for the product.
The product and accessories that come with your camera may be different from
those described in this manual. This is due to the fact that different retailers often
specify slightly different product inclusions and accessories to suit their market
requirements, customer demographics, and geographical preferences. Products
very often vary between retailers especially with accessories such as batteries,
chargers, AC adapters, memory cards, cables, pouches, and language support.
Occasionally a retailer will specify a unique product color, appearance, and internal
memory capacity. Contact your dealer for precise product definition and included
accessories.
The illustrations in this manual are for the purpose of explanation and may differ
from the actual design of your camera.
The manufacturer assumes no liability for any errors or discrepancies in this user
manual.
EN-3
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
Warnings
If foreign objects or water have entered the camera, turn the power off
and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
If the camera has fallen or its case has been damaged, turn the power
off and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
Do not disassemble, change or repair the camera.
This might cause fire or electric shock. For repair or internal inspection, ask
the store of purchase.
Use the supplied AC adapter only with the indicated power supply
voltage.
Use with any other power supply voltage might cause fire or electric shock.
Do not use the camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow,
on the beach, or near the shore.
Do not place the camera on inclined or unstable surfaces.
This might cause the camera to fall or tilt over, causing damage.
Keep the battery out of the reach of children.
Swallowing the battery might cause poisoning. If the battery is accidentally
swallowed, immediately consult a physician.
Do not use the camera while you are walking, driving or riding a
motorcycle.
This might cause you to fall over or result in traffic accident.
EN-4
Cautions
Insert the battery paying careful attention to the polarity (+ or –) of the
terminals.
Inserting the battery with its polarities inverted might cause fire and injury, or
damage to the surrounding areas due to the battery rupturing or leaking.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to
leak. If the internal fluid enters your eyes or comes into contact with your
body or clothes, rinse with fresh water. If the internal fluid has entered your
eyes, consult a physician to receive treatment.
A camera is a precision instrument. Do not drop it, strike it or use
excessive force when handling the camera.
This might cause damage to the camera.
Do not use the camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of continuous
use.
The battery becomes hot during use. Touching a hot battery might cause
burns.
Do not wrap the camera or place it in cloth or blankets.
This might cause heat to build up and deform the case, resulting in fire. Use
the camera in a well-ventilated place.
Do not leave the camera in places where the temperature may rise
significantly, such as inside a car.
This might adversely affect the case or the parts inside, resulting in fire.
Before you move the camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and
electric shock.
CONTENTS
EN-6
EN-7
INTRODUCTION
Overview
Congratulations on your purchase of the new digital camera.
Capturing high-quality digital images is fast and easy with this state-of-the-art smart
camera. Equipped with a 8.0-megapixel CCD, this camera is capable of capturing
images with a resolution of up to 3264 x 2448 pixels.
Package Contents
Carefully unpack your camera and ensure that you have the following items:
Common Product Components:
Digital Camera
User’s manual
Software CD-ROM
USB cable
AV cable
Camera strap
AC power adapter
Rechargeable lithium-ion battery
Accessories and components may vary by retailer.
EN-8
GETTING TO KNOW YOUR CAMERA
Front View
12 43 5
8 7
6
1. Shutter button
2. ON/OFF button
3. Self-timer LED
4. Mode switch
Capture mode
Video mode
Playback mode
5. Speaker
6. Lens
7. Microphone
8. Flash
EN-9
Rear View
12 4
35
6
7
8
9
101112
1. LCD monitor
2. Delete button
3. DISP Display button
4. MENU Menu button
5. Zoom in button
Zoom out button
6. Strap holder
7. DC IN 5V terminal
8. USB or AV OUT terminal
9. Battery / Memory card cover
10. SET / Direction button
button
Focus button
button
Flash button
button
Self-timer button
button
Backlight/Exposure
compensation button
SET Set button
11. Status LED
12. Tripod socket
EN-10
LCD Monitor Display
Capture mode
1. Zoom status
2. Voice memo
3. Battery condition
[ ] Full battery power
[ ] Medium battery power
[ ] Low battery power
[ ] No battery power
* [ ] AC adapter icon (if used)
4. Flash mode
[ Blank] Auto Flash
[ ] Red-eye Reduction
[ ] Forced Flash
[ ] Flash Off
5. [ ]Histogram
6. Main focus area (When the shutter
button is pressed halfway)
7. Capture mode icon
[Blank] Single
[ ] Continuous
[AEB] Auto Exposure Bracketing
8. Image size resolution
[ ] 3264 x 2448
[ ] 2816 x 2112
[ ] 2272 x 1704
[ ] 1600 x 1200
[ ] 640 x 480
9. Available number of shots
10. Image quality
[ ] Fine
[ ] Standard
[ ] Economy
11. Date and time
12. Self-timer icon
[ 10S] 10 sec.
[ 2S ] 2 sec.
[ 10+2 ]10+2 sec.
13. Slow shutter warning
14. [ ] Exposure compensation
[ ] Backlight correction
(Adjust exposure value with the c d /
buttons)
15. Metering
[Blank] Center
[ ] Spot
16. White balance
[Blank] Auto
[ ] Incandescent
[ ] Fluorescent 1
[ ] Fluorescent 2
[ ] Daylight
[ ] Cloudy
[ ] Manual
17. Focus setting
[Blank] Auto focus
[ ] Face detection
[ ] Macro
[ ] Infinity
18. Scene mode
[ ] Program AE
[ ] Panorama
[ ] Portrait Man
[ ] Portrait Lady
[ ] Landscape
[ ] Sports
[ ] Night Portrait
[ ] Night Scene
[ ] Candlelight
[ ] Fireworks
[ ] Text
[ ] Sunset
[ ] Sunrise
[ ] Splash Water
[ ] Flow Water
[ ] Sepia
[ ] Monochrome
[ ] Snow
[ ] Beach
[ ] Pets
[ ] Anti Shake
[ ] User Setting
1
2
P
EN-11
Video mode [ ]
1. Mode icon
2. Zoom status
3. Battery condition
4. Video resolution
5.
Available recording time/Elapsed time
6. Video quality
7. Recording indicator
8. Self-timer icon
9. Focus setting
Playback mode
[ ]
- Still image playback
1. Mode icon
2. File number
3. Folder number
4. Protect icon
5. Voice memo
6. DPOF icon
Playback mode
[ ]
-
Video playback
1. Video status bar
2. Elapsed time
3. File number
4. Folder number
5. Protect icon
6. Mode icon
7. Play mode
8. Sound off icon (When the
c
button is pressed
during video playback)
9. Total recorded time
00:07:30
00:07:30
00:07:30
00:07:3000:07:30
10S
10S
10S
10S10S
6
1
1
1
11
100-0011
100-0011
100-0011
100-0011100-0011
35 46
T
T
T
TTotal
otal
otal
otalotal
Play
Play
Play
PlayPlay
00:00:10
00:00:10
00:00:10
00:00:1000:00:10 00:00:
00:00:
00:00:
00:00:00:00:
06
06
06
0606
1
2
9
78
EN-12
GETTING STARTED
Preparation
1. Attach the camera strap.
2. Open the battery/memory card cover.
3. Insert the supplied battery with correct orientation as
shown.
4. Insert an SD/SDHC memory card (Optional).
The camera has
32MB internal memory (29MB
available for image storage)
, but you can load an
SD/SDHC memory card to expand the camera’s
memory capacity.
Be sure to format the memory card with this
camera before its initial usage.
5. Close the battery/memory card cover and make sure it
is locked securely.
To prevent valuable data from being accidentally erased from
an
SD/SDHC memory card
, you can slide the write protect tab
(on the side of the
SD/SDHC
memory card) to “LOCK”.
To save, edit, or erase data on an SD/SDHC memory card,
you must unlock the card.
To prevent damaging of an SD/SDHC memory card, be sure
to turn off the power when inserting or removing the SD/
SDHC memory card. If inserting or removing the SD/SDHC
memory card with the power on, the camera will automatically turn off.
EN-13
Charging the Battery
The AC power adapter may charge the battery or operate as the camera's power
supply. Make sure that the camera is turned off and the battery is inserted before
starting.
1. Insert one end of the AC power adapter
into the DC IN 5V terminal of the camera.
2. Insert the other end of the AC power
adapter into a wall outlet.
The status LED lights red when
charging has started and the LED turns
off when charging is completed. The
LED lights green when a charging error
has occurred or no battery is inserted
inside the camera.
It is recommended that you fully discharge the battery before recharging.
Charging time varies according to the ambient temperature and the status of
battery.
This camera must use with the specified battery and AC power adapter for battery charging.
Damage caused by using of an incorrect adapter is not covered under the warranty.
The battery may feel warm after it has been charged or immediately after being used. This is
normal and not a malfunction.
When using the camera in cold areas, keep the camera and battery warm by holding them inside
your outer clothes.
EN-15
Choosing the Language
Specify in which language menus and messages are to be displayed on the LCD monitor.
1. Slide the mode switch
to [ ], [ ] or [ ]
, and
press the
MENU
button.
2. Select [Setup] menu with the f button.
3. Select [Language] with the
c
/
d
buttons and press
the
SET
button.
4. Select the displayed language with the
c
/
d
buttons and press the
SET
button.
The setting will be stored.
Formatting the Memory Card or Internal Memory
This utility formats the internal memory (or memory card) and erases all stored images
and data.
1. Slide the mode switch to [ ], and press the
MENU button.
2. Select [Setup] menu with f button.
3. Select [Format] with the
c
/
d
buttons, then
press the
SET
button.
4. Select [Execute] with the
c
/
d
buttons, and
press the
SET
button.
To cancel formatting, select [Cancel] and
press the
SET
button.
Capture
SET:Adj.MENU:Exit
Play
SET:Adj.
MENU:Exit
Format
SET:Enter
EN-16
CAPTURE MODE
Capturing Images
Your camera is equipped with a 2.7" full color TFT LCD monitor to help you compose
images, playback recorded images/video clips or adjust menu settings.
1. Press the ON/OFF button to turn the power on.
The status LED lights green and the camera is initiated.
When the power is turned on, the camera will start in the mode that was last set.
If the power is turned on in [ ] or [ ] mode, the lens will extend forward and it
is ready for shooting. In both modes, if the mode switch is set to [ ], the lens
barrel will retract into the camera body after 30 seconds.
If the power is turned on in [ ] mode, the lens will remain closed.
2. Slide the mode switch to [ ].
3. Compose your image in the LCD monitor.
Pressing the button zooms in on the subject, and enlarges the subject on the
LCD monitor.
Pressing the button provides a wider angle image.
4. Press the shutter button. a
b
Pressing the shutter button down halfway
automatically focuses and adjusts the
exposure, and pressing the shutter button
down fully captures the images.
The focus area frame turns green when
the camera is in focus and the exposure is
calculated.
When the focus or exposure is not
suitable, the frame of the focus area turns
red.
If the photographic preview is set to [On], the captured image will be displayed
while the image is being recorded onto the SD/SDHC memory card.
EN-17
Recording Shots using Face Detection Technology
Face Detection Technology can identify and focus on the human faces in the image.
This advanced function simultaneously detects up to 5 human faces regardless of their
position in the scene.
1. Slide the mode switch to [ ].
2. Toggle the button until [ ] icon appears on the LCD monitor.
The white frame is identified as the “top priority” face (main focus frame), and
gray ones around the other faces.
3. Press the shutter button halfway down to lock the focus.
The main focus frame simultaneously turns green.
If the “top priority” face is out of focus, the main focus frame turns red.
4. Press the shutter button down fully to capture your image.
Subjects that are not suitable with this function:
a. A person is wearing glasses, sunglasses, or face is covered with hat or hair.
b. A person turned sideways.
Face detection function is on
White frame Green frame Red frame
Focus lock Out of focus
EN-18
Recording Voice Memos
A voice memo can be recorded once for 30 seconds in the still image mode immediately
following a still image capture.
1. Slide the mode switch to [ ].
2. Press the MENU button, and select the
[Function] menu with the button.
3. Select [Voice Memo] with the / buttons,
and press the SET button.
4. Select [On] with the / buttons, and press
the SET button.
5. Press the MENU button to exit from the menu.
An [ ] icon is displayed on the screen.
6. Compose the image, press the shutter button down halfway, then press it down fully.
[VOICE RECORDING] is displayed on the screen immediately, and the voice
memo recording starts.
7. Press the shutter button one more time during recording, or wait for 30 seconds.
[VOICE RECORD END] will be displayed and the recording will end.
An [ ] icon is displayed with images that have been recorded with a voice
memo.
SET:Adj.MENU:Exit
EN-19
VIDEO MODE
Recording Video Clips
This mode allows you to record video clips at a resolution of 320 x 240 / 640 x 480 pixels.
1. Slide the mode switch to [ ].
2. Compose the image.
3. Press the shutter button.
The recording of the video clip will start.
Pressing the shutter button one more time will end
the recording of the video clip.
The recording time depends on the storage size
and the subject of the image to be recorded.
The zoom function cannot be used during video
recording.
When recording a video clip, the flash and "10+2 sec." self-timer function cannot be used.
If the write speed of your SD/SDHC memory card is not fast enough for recording video clips in
the currently selected quality, a warning icon [ ] will appear, and the video recording will stop. In
this case, select a video quality lower than the current one.
Playing Back Video Clips
You can play back recorded video clips on the camera. You can also play back sound if
recorded with the video.
1. Slide the mode switch to [ ].
The last image appears on the screen.
2. Select the desired video clip with the / buttons.
3. Press the SET button.
A press of the
/
buttons during playback allows fast forward play / fast reverse play.
To stop video playback, press the button.
This stops playback and returns to the start of the video clip.
To pause video playback, press the SET button.
This pauses video playback.
To cancel pause, press the SET button again.
Video clips cannot be displayed rotated or enlarged.
Windows Media player or QuickTime Player is recommended to play back the video clip on your
computer.
QuickTime Player is a free media player available at www.apple.com; and compatible with Mac
and Windows computers.
For more information about the operation of the media player, refer to its respective help documentation.
EN-20
PLAYBACK MODE
Playing Back Still Images
You can play back the still images on the LCD monitor.
1. Slide the mode switch to [ ].
The last image appears on the screen.
2. The images can be displayed in forward or
reverse sequence with the / buttons.
To view the previous image, press the
button.
To view the next image, press the button.
Pressing the
/
buttons during image
playback
will result in a 90-degree rotated display.
The
button rotates the image counterclockwise
and displays it, whereas the
button rotates the
image clockwise and displays it. A press of the
button opposite to the direction in which the image
was rotated will return the image to the normal
display
.
Pressing the button enlarges the image.
To return to normal magnification, press the
button.
An [ ] icon is displayed with the video data. Video clips cannot be rotated.
An [ ] icon is displayed with images which have an audio memo recorded.
Press the button to playback the voice memo data.SET
EN-21
Thumbnail Display
This function allows you to view 9 thumbnail images on the LCD monitor at the same
time, which can let you quickly search for the image that you want.
1. Slide the mode switch to [ ].
The last image appears on the screen.
2. Press the button.
The images are displayed in the thumbnail display.
Images that have been selected with the
e
/
f
/
c
/
d
buttons will be indicated by a yellow frame.
When there are ten or more images, scroll the
screen with the c / d buttons.
3. Press the e f / / c d / buttons to select the image
to be displayed at regular size.
4. Press the SET button.
The selected image is displayed at its regular size.
An [ ], [ ], [ ], [ ] icon may be displayed in a thumbnail.
Removing Red-eye
You can use this function to remove the red-eye effect after an image is taken.
1. Slide the mode switch to [ ].
2. Select the image that you want to edit with the
e
/
f
buttons.
3. Press the MENU button.
4. Select [Fix Red Eyes] with the c / d buttons, and
press the SET button.
5. Select [Execute] with the c / d buttons, and press
the SET button.
6. View the changes on the corrected image.
7. To save your corrected image, select [Confirm] with
the c / d buttons, and press the SET button.
When this process ends, this replaces the original
image with the corrected image.
SET:Adj.
MENU:Exit
SET:Enter
EN-22
Attaching Voice Memos
A maximum of 30 seconds of audio can be recorded as a memo for captured still
images. The voice memo can be recorded only once.
1. Slide the mode switch to [ ].
The last image appears on the screen.
2. Select the image to which you want to attach the voice memo with the /
buttons.
3. Press the shutter button.
[VOICE RECORDING] is displayed on the screen and recording starts.
4. To stop recording a voice memo as it is being recorded, press the shutter button
again.
[VOICE RECORD END] will be displayed and the recording will end. An [ ] icon
is displayed with images that have been recorded with a voice memo.
Playing back voice memo
A press of the
SET
button displays [VOICE PLAYBACK] and plays back the voice memo.
Voice memo is only available for still images.
EN-23
Protecting Images
Set the data to read-only to prevent images from being erased by mistake.
1. Slide the mode switch to [ ].
2. Select the image that you want to protect with the
e
/
f
buttons.
3. Press the MENU button.
4. Select [Protect] with the c / d buttons, and press the
SET button.
5. Select [Single] or [All] with the c d / buttons, and press
the SET button.
6. Select [Set] with the c / d buttons, and press the SET
button.
Protection is applied to the image and the camera
returns to the playback mode.
The protect icon
[ ]
is displayed with protected images.
When [All] has been selected, [ ] is displayed
with all the images.
Canceling the Protection
To cancel protection for only one image, display the image on which
you want to remove the image protection.
1. Select [Protect] with the c / d buttons from the playback
menu, and press the SET button.
2. Select [Single] or [All] with the c d / buttons, and press
the button.SET
3. Select [Cancel Protect] with the c / d buttons, and press
the button.SET
The removal of image protection is executed and the camera
returns to the playback mode.
Protecting multiple images simultaneously
1. Select [Protect] with the
c
/
d
buttons from the playback menu, and press the
SET
button.
2. Select [Select] with the c / d buttons, and press the SET button.
The images are displayed in the thumbnail display.
3. Select the image you want to protect with the
e
/
f
/
c
/
d
buttons, and press the
DISP
button.
The protect icon [ ] is displayed with protected images. Selecting a protected image
and pressing the
DISP
button again will cancel the protection. This procedure is
repeated to select multiple images.
4. Press the SET button.
Protection and cancellation of the protectionare are executed and the camera returns
to playback mode.
Formatting an SD/SDHC memory card overrides protection, and erases all images regardless of
their protected status.
SET:Adj.
MENU:Exit
SET:Enter
MENU:Exit
SET:Enter
MENU:Exit
EN-24
DPOF Settings
DPOF is the abbreviation for Digital Print Order Format, which allows you to embed
printing information on your memory card. You can select the images to be printed and
how many prints to make with the DPOF menu in the camera and insert the memory
card to the card compatible printer. When the printer starts printing, it will read the
embedded information on the memory card and print the specified images.
1. Slide the mode switch to [ ].
2. Select the image that you want to set DPOF with the
  / buttons.
3. Press the MENU button.
4. Select [DPOF] with the / buttons, and press the
SET button.
The DPOF setting screen is displayed.
5. Select [Single] or [All] with the / buttons, and
press the SET button.
[Single]: Sets DPOF for each individual image.
[All]: Sets DPOF for all images at once.
6. Select [Print Num] with the / buttons, and press
the SET button.
This displays the number of prints setting screen.
7. Set the number of prints with the / buttons, and
press the SET button.
You can set up to 9 prints for each image.
8. Select [Date Print] with the / buttons, and press
the SET button.
The date setting screen appears.
9. Select date to [On] or [Off] with the / buttons, and
press the SET button.
[On]: The date of the image will also be printed.
[Off]: The date of the image will not be printed.
10.Select [Print Enable] with the   / buttons, and press
the SET button.
11. Select [Execute] with the / buttons, and press the
SET button.
This creates a file containing the DPOF information,
and when the operation is finished, the screen returns to the playback mode.
The DPOF icon [ ] is displayed on each image that has set up DPOF settings.
The date that is printed on the image is the date set on the camera. To print the correct date on
the image, set the date on the camera before you capture the image. Refer to section in this
manual titled “Setting the Date and Time” for further details.
SET:EnterMENU:Exit
SET:Enter
MENU:Exit
100-0008
100-0008
100-0008
100-0008100-0008
1
1
1
11
SET:Adj.MENU:Exit
EN-25
Erasing Images
Erasing in Photography Mode (Quick Delete Function)
The quick delete function enables you to delete the last-captured image during capture.
1. Slide the mode switch to [ ] or [ ].
2. Press the button.
The last image and quick delete menu
appear on the screen.
3. Select [Execute] with the c d / buttons.
4. Press the SET button to confirm the deletion.
To not delete, select [Cancel], and press the
SET button.
Erasing in Playback Mode
Erasing single image / Erasing all images
1. Slide the mode switch to [ ].
The last image will be displayed on the
screen.
2. Select the image you want to erase with the
e
/
f
buttons.
3. Press the button.
The deletion menu will be displayed.
4. Select [Single] or [All] with the c d / buttons,
and press the SET button.
[Single]: Erases the selected image or the
last image.
[All]: Erases all of the images except for the
protected images.
[Select]: Erases a number of selected
images.
5. Select [Execute] with the c / d buttons, and
press the SET button.
To not erase, select [Cancel], and press the SET button.
SET:Enter
MENU:Exit
MENU:Exit SET:Enter
EN-26
Erasing selected images
This erases a number of selected images.
1. Slide the mode switch to [ ].
2. Press the button.
The deletion menu will be displayed.
3. Select [Select] with the / buttons, and
press the SET button.
The images are displayed in the thumbnail
display.
4. Select the image you want to erase with the /
   / / buttons, and press the button.
The [ ] icon will be displayed. One more
press of the button will cancel the
operation. Repeat this procedure and select
all the images that you want to erase.
5. Press the SET button.
Deleting an image will not affect sequential image numbering. For example, if you delete image
number 240, the next captured image will be numbered 241 even though 240 no longer exists. In
other words, an image-number is retired when an image is deleted and will not be reused or
reassigned to another subsequently captured image.
SET:Enter
MENU:Exit
EN-27
MENU OPTIONS
Capture Menu
This menu is for the basic settings to be used when capturing still images.
1. Slide the mode switch to [ ].
2.
Press the MENU button, and select the [Capture] / [Function] / [Setup] menu with the
e f / button
s
.
3. Select the desired option item with the c d / buttons, and press the SET button to
enter its respective menu.
4. Select the desired setting with the c / d buttons, and press the SET button.
5. To exit from the menu, press the MENU button.
Scene Mode
Select from 22 different scene modes in accordance with the shooting conditions.
* Program AE / Panorama / Portrait Man / Portrait Lady / Landscape / Sports / Night Portrait /
Night Scene / Candlelight / Fireworks / Text / Sunset / Sunrise / Splash Water / Flow Water /
Sepia / Monochrome / Snow / Beach / Pets / Anti Shake / User Setting
Size
This sets the size of the image that will be captured.
* [ ] 3264 x 2448
* [ ] 2816 x 2112
* [ ] 2272 x 1704
* [ ] 1600 x 1200
* [ ] 640 x 480
Quality
This sets the quality (compression) at which the image is captured.
* [ ] Fine
* [ ] Standard
* [ ] Economy
Sharpness
This sets the sharpness of the image that will be captured.
* Hard / Normal / Soft
Saturation
This sets the saturation of the image that will be captured.
* High / Normal / Low
SET:Adj.MENU:Exit SET:Adj.MENU:Exit SET:Adj.MENU:Exit
EN-29
LCD Bright.
Select a brightness level for the LCD monitor.
The LCD becomes brighter with the button and darker with the button. The
adjustment range is from -5 to +5.
Digital Zoom
This sets whether or not to use digital zoom at the time of photography.
* On / Off
Preview
This sets whether or not to display the captured image on the screen immediately after
the image is captured.
* On / Off
Date Print
The date of recording can be printed directly on the still images. This function must be
activated before the image is captured.
* On / Off
EN-30
Video Menu
This menu is for the basic settings to be used when recording video clips.
1. Slide the mode switch to [ ].
2. Press the
MENU
button, and select the [Capture]/ [Function]/ [Setup] menu with the
/
buttons.
3. Select the desired option item with the / buttons, and press the SET button to
enter its respective menu.
4. Select the desired setting with the   / buttons, and press the SET button.
5. To exit from the menu, press the MENU button.
Size
This sets the size of the video clip that will be captured.
* [ ] 640 x 480
* [ ] 320 x 240
Quality
This sets the quality (compression) at which the video clip is captured.
* [ ] Fine
* [ ] Standard
Color
This sets the color of the video clip that will be captured.
* Normal / Vivid / Sepia / Monochrome
Audio
This sets whether or not to record audio at the time of video recording.
* On / Off
LCD Bright.
Refer to section in this manual titled “LCD Bright.” in Capture Menu for further details.
Digital Zoom
Refer to section in this manual titled “Digital Zoom” in Capture Menu for further details.
SET:Adj.MENU:Exit SET:Adj.MENU:Exit
EN-31
Playback Menu
In the [ ] mode, choose which settings are to be used for playback.
1. Slide the mode switch to [ ].
2. Press the MENU button.
3. Select the desired option item with the c / d buttons, and press the SET button to
enter its respective menu.
4. Select the desired setting with the c / d buttons, and press the SET button.
5. To exit from the menu, press the MENU button.
Fix Red Eyes
Refer to section in this manual titled “Removing Red-eye” for further details.
Slide Show
This function enables you to playback your still images automatically in order one image at
a time.
* 3 sec. / 5 sec. / 10 sec.
DPOF
Refer to section in this manual titled “DPOF Settings” for further details.
Protect
Refer to section in this manual titled “Protecting Images” for further details.
LCD Bright.
Refer to section in this manual titled “LCD Bright.” in Capture Menu for further details.
Resize
Resizes a previously saved image. Resizing replaces the original image with the changed
image. It is only possible to resize to a smaller size.
Quality
Changes the quality (compression) of a recorded image. Compresses images down to half
of their size or less, overwrites old size images with newly compressed images. It is only
possible to reduce the image quality/size, never to increase it.
Copy to Card
Allows you to copy your files from the camera’s internal memory to an SD/SDHC memory card. Of
course, you can only do this if you have a memory card installed and some files in internal memory.
* Cancel / Execute
SET:Adj.
MENU:Exit
SET:Adj.
MENU:Exit
EN-33
TRANSFERRING FILES TO YOUR
COMPUTER
System Requirement
Downloading Your Files
1. Connect one end of the USB cable to an available
USB port on your computer.
2. Connect the other end of the USB cable to the
USB terminal on the camera.
3. Turn on your camera.
4. Select [PC] using the / buttons and press
the SET button.
5. From the Windows desktop, double click on “My
Computer”.
6. Look for a new “removable disk” icon.
This “removable disk” is actually the memory (or memory card) in your camera.
Typically, the camera will be assigned drive letter “e” or higher.
7. Double click on the removable disk and locate the DCIM folder.
8. Double click on the DCIM folder to open it to find more folders.
Your recorded images and video clips will be inside these folders.
9. Copy & Paste or Drag-N-Drop image and video files to a folder on your computer.
Mac users: Double-click the “untitled” or “unlabeled” disk drive icon on your desktop.
iPhoto may automatically launch.
Windows Macintosh
Pentium III 600 MHz or higher
Windows 2000/XP/Vista
128MB RAM
128MB hard disk space
CD-ROM drive
Available USB port
PowerPC G3/G4/G5
OS 9.0 or later
128MB RAM
128MB hard disk space
CD-ROM drive
Available USB port
EN-34
USING THE CAMERA AS A PC CAMERA
Your camera can act as a PC camera, which allows you to videoconference with busi-
ness associates, or have a real-time conversation with friends or family. To use the cam-
era for videoconferencing, your computer system must include the items as below:
Microphone
Sound card
Speakers or headphones
Network or Internet connection
1. After installing the PC camera driver (included on the CD-ROM) in your Windows
operating system, restart your computer.
2. Connect one end of the USB cable to the USB terminal of the camera.
3. Connect the other end of the USB cable to an available USB port on your computer.
4. Turn on your camera.
5. Select [PC Camera] with the / buttons and press the SET button.
6. Position the camera steadily on top of your computer monitor or use a tripod.
7. Launch the videoconferencing application software.
Simply follow the instructions in the application software to start your camera.
This function is not supported by Mac.
You are recommended to use MediaOne Gallery SE (included on the CD-ROM) or Windows
Netmeeting (Windows Meeting Space on Windows Vista) as a videoconferencing application
software.
The video resolution for videoconferencing applications is generally 320 x 240.
For more information about the operation of videoconference application software, refer to its
respective help documentation.
EN-36
SPECIFICATIONS
* Design and specifications are subject to change without notice.
Item Description
Image sensor 1/2.5” CCD sensor (8.0 megapixels)
Image resolution <Still image>
3264 x 2448, 2816 x 2112, 2272 x 1704, 1600 x 1200, 640 x 480
<Video clip>
640 x 480 (25 fps), 320 x 240 (25 fps)
LCD monitor 2.7” full color TFT LCD (230K pixels)
Recording media 32MB internal memory (29MB available for image storage)
Supports SD/SDHC memory card (up to 4GB) (optional)
File format JPEG, DCF 1.1, EXIF 2.2, DPOF, AVI
Lens 4x optical zoom lens
Aperture range: 2.7(W) - 5.4(T)
Focal length:4.6mm - 18.4mm (equivalent to 28mm - 112mm on a
35mm camera)
Focus Range Standard
0.5m to infinity
Macro
Wide: 0.05m to infinity
Tele: 0.35m to infinity
Shutter speed 1 - 1/1500 sec.
Digital zoom 5x (Capture mode)
4x (Playback mode)
Flash effective
range
0.5m - 3.0m (Wide)
0.5m - 2.1m (Tele)
Terminals DC IN 5V
AV OUT
USB 2.0 compliant
Power supply Rechargeable Lithium-ion battery (3.7V)
AC power adapter (5V/2A)
Dimensions
Approx.
94 x 55 x 24
mm (without protruding parts)
Weight Approx. 132g (without battery and memory card)
EN-37
APPENDIX
Possible Number of Shots
Possible number of shots (still image)
The table shows the approximate shots that you can capture at each setting based on
the capacity of the internal memory and the SD/SDHC memory card.
Possible recording time / sec (video clip)
* We recommend a memory card of at least 10MB/Sec write speed to prevent auto stop or
unexpected results. If you experience an error using a slower SD/SDHC memory card, you
can set your camera’s video recording to QVGA (320 x 240) and standard quality.
Size Quality
Internal
Memory
SD/SDHC memory card capacity
128MB 256MB 512MB
1GB 2GB
4GB
SDHC
3264 x 2448
Fine 10 45 91 183 368 738 1478
Standard 13 58 118 238 477 955 1913
Economy
16 71 143 289 579 1160 2323
2816 x 2112
Fine 14 63 127 255 512 1025 2053
Standard 18 79 159 320 642 1285 2573
Economy
19 83 167 336 674 1349 2701
2 x 1272 704
Fine 24 103 209 420 842 1686 3374
Standard 27 116 233 469 939 1881 3765
Economy
32 137 276 554 1111 2225 4454
1600 x 1200
Fine 49 209 415 833 1669 3342 6688
Standard 59 246 495 993 1990 3984 7974
Economy
67 279 561 1126 2255 4515 9037
640 x 480
Fine 152 628 1263 2535 5076 10160 20335
Standard 184 762 1531 3072 6153 12316 24649
Economy
229 945 1900 3812 7634 15279 30579
Size Quality
Internal
Memory
SD/SDHC memory card capacity
128MB 256MB 512MB
1GB 2GB
4GB
SDHC
640 x 480
Fine 00:00:12 00:00:53 00:01:47 00:03:35 00:07:12 00:14:25 00:28:51
Standard 00:00:14 00:01:00 00:02:02 00:04:05 00:08:11 00:16:24 00:32:50
Fine 00:00:39 00:02:42 00:05:27 00:10:57 00:21:56 00:43:54 01:27:52
Standard 00:00:45 00:03:09 00:06:20 00:12:42 00:25:26 00:50:55 01:41:55
EN-38
Troubleshooting
Refer to the symptoms and solutions listed below before sending the camera for repairs.
If the problem persists, contact your local reseller or service center.
Symptom Cause Solutions / Corrective Actions
The power does not come
on.
The battery is not inserted. Insert the battery correctly.
The battery is exhausted. Recharge the battery.
The battery runs out quickly. The battery is not fully charged.
The battery is not used for an
extended period of time after
being charged.
Fully charge the battery and
discharge it for at least one complete
cycle before use to maximize its
performance and lifetime.
The battery or camera feels
warm.
Long period of continuous use of
the camera or the flash.
Even if I press the shutter
button, the camera does not
take a picture.
The shutter button is not pressed all
the way down.
Press the shutter button all the
way down.
The memory card does not have
any free capacity.
Insert a new memory card, or
delete unwanted files.
The flash is charging.
Wait until the status LED is off.
The memory card is
write-protected.
Remove the write-protection.
Images do not appear on the
LCD monitor.
LCD monitor is dark. Adjust the brightness of the
LCD monitor in the menu.
Although it is set to auto
focus, it does not focus.
The lens is dirty. Wipe clean with a soft, dry cloth or
lens paper.
The distance to the subject is
smaller than the effective range.
Get your subject within the effective
focus range.
The contents on the memory
card cannot be played back.
You played back a memory card that
was not formatted by this
camera
.
Insert a memory card that was
formatted on this camera.
Files cannot be deleted. The file is protected. Cancel protection.
The memory card is write-protected.
Remove the write-protection.
Even when the camera’s
buttons are pressed, it does
not operate.
The battery is running low. Recharge the battery.
The date and time are
wrong.
The correct date and time is not set.
Set the correct date and time.
Cannot download images. The free space on the hard disk in
your computer may be insufficient.
Check whether the hard disk has
space for running Windows, and
if the drive for loading image files
has a capacity at least that of the
memory card inserted in the camera.
No power supply. Use an AC power adapter.
Recharge the battery.
EN-39
Connecting to a PictBridge Compliant Printer
If a printer that supports PictBridge is available, images can be printed by connecting the
digital still camera directly to the PictBridge-compatible printer without using a computer.
Connecting the camera to the printer
1. Connect one end of the USB cable to your
camera.
2. Connect the other end of the USB cable to the
USB port on the printer.
3. Turn on your camera.
4. The [USB] screen is displayed. Select [Printer]
with the
c d /
buttons, and press the
SET
button.
Printing images
When the camera is properly connected to a PictBridge compliant printer, the PictBridge
menu is displayed on the monitor.
1. Select the item you want to configure with the
c d / buttons, and press the SET button.
[Images]:Select whether you want to print
specific image or all images. You may also
select printing number for specific image.
[Date Print]:According to the printer type,
select whether you want to print the image
with date imprint or not.
[Paper Size]:Select the desired paper size
according to the printer type.
[Layout]:Select the desired printing layout according to the printer type.
[Print]:After all settings are configured, select this item to start printing.
2. If you select [Images] in the previous step, the
figure shown on the right hand side will appear.
Select [Select], [All] or [DPOF] with the / c d
buttons, and press the SET button.
[Select]:Select to print one specific image.
[All]:Select to print all images.
[DPOF]:Select to print images with DPOF
settings.
[Exit]:Exit from Images option.
SET:Enter
SET:Enter
EN-40
3. If you select [Select] in the previous step, the
figure shown on the right hand side will appear.
Select the image that you want to print with
the e / f buttons.
Select the [Print Num] (up to 99) with the
c /
d
buttons.
After selecting the desired image and
printing number, press the SET button to
confirm.
4. Select [Exit] with the c / d buttons, and press
the SET button.
5. Select [Print] with the c / d buttons, and press
the SET button to start printing.
6. The printing starts and the figure shown on the
right hand side appears.
[COMPLETE] will be displayed temporarily,
reminding you that the printing procedure is
finished.
If an error is detected during the connection
(i.e. the printer hardware problem) between
camera and printer, [PRINT ERROR] will be
displayed.
If an error is detected during the communication (i.e. wrong setting on the
camera) between camera and printer, [ERROR] will be displayed.
The image printing may fail if the power to the camera is cut off.
We recommend that you use the AC power adapter when connecting the camera to the printer.
Select
SET:Enter105-0003
SET:Enter
SET:Enter
PRINTING
PRINTING
PRINTING
PRINTINGPRINTING
EN-41
A. Information on Disposal for Users (private households)
1.In the European Union
Attention: If you want to dispose of this equipment, please do not use
the ordinary dust bin!
Used electrical and electronic equipment must be treated separately
and in accordance with legislation that requires proper treatment,
recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households
within the EU states may return their used electrical and electronic
equipment to designated collection facilities free of charge*. In some
countries* your local dealer may also take back your old product free of
charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumu-
lators, please dispose of these separately beforehand according to
local requirements.
By disposing of this product correctly you will help ensure that the
waste undergoes the necessary treatment, recovery and recycling and
thus prevent potential negative effects on the environment and human
health which could otherwise arise due to inappropriate waste han-
dling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities
and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be
returned free of charge to the dealer, even if you donít purchase a new
product. Further collection facilities are listed on the homepage of
www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your local dealer who will inform you about the
take-back of the product. You might be charged for the costs arising
from take-back and recycling. Small products (and small amounts)
might be taken back by your local collection facilities.
For Spain: Please contact the established collection system or your
local authority for take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your
localauthorities and ask for the correct method of disposal.
Att
en
ti
on:
Y
our pro
d
-
uct is marked with this
symbol. It means that
used electrical and
electronic products
should not be mixed
with general house-
hold waste. There is a
separate collection
system for these prod-
ucts.

Specyfikacje produktu

Marka: Minox
Kategoria: Niesklasyfikowane
Model: DC 8011

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Minox DC 8011, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Minox

Minox

Minox RS-4 Instrukcja

5 Października 2024
Minox

Minox MS 8x25 Instrukcja

5 Października 2024
Minox

Minox ZP 8 Instrukcja

5 Października 2024
Minox

Minox DD 100 Instrukcja

26 Września 2024
Minox

Minox 35 PE Instrukcja

26 Września 2024
Minox

Minox DC 9011 Instrukcja

26 Września 2024
Minox

Minox B Instrukcja

26 Września 2024
Minox

Minox LX Instrukcja

26 Września 2024
Minox

Minox DC 6022 Instrukcja

26 Września 2024
Minox

Minox DC 8011 Instrukcja

26 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
Rock N Roller

Rock N Roller R14G Instrukcja

29 Stycznia 2025
Rock N Roller

Rock N Roller R6RT Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
Shimbol

Shimbol Memory I PRO Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025