Instrukcja obsługi Metra 70-7864DZ


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Metra 70-7864DZ (4 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
INSTALLATION INSTRUCTIONS FOR PART 70-7864DZ
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION-2009
APPLICATIONS
HONDA ACCORD
2003-0 Honda Accord adapter to adapt7
the Metra 99-7864 kit for dual zone
climate control applications
Instructions
IMPORTANT: If rear window defogger function is desired, professional installation is
STRONGLY RECOMMENDED .Disconnect the negative battery terminal to prevent an
accidental short circuit.
1. Disconnect the negative battery terminal to prevent an accidental short circuit.
2. Disassemble the dash as per the 99-7864 instructions.
3. Connect the 22-way green plug of the dual zone harness to the installation kit and
connect the 22-way and 16-way green caps of the dual zone harness to their mates
in the vehicle.
* If rear window defogger function is not desired, tape off yellow/green
wire to prevent an accidental short circuit, then installation of the dual
zone harness is complete.
Small Flat Blade Screwdriver I Socket Wrench
TOOLS REQUIRED:
70-7864DZ
For rear window defogger function to be retained, follow the steps below. Remember
that professional installation is STRONGLY RECOMMENDED.
1.
Follow steps 1-3 to install dual zone harness.
2.
Remove (1) Phillips screw from bottom of panel below steering wheel
unclip panel and remove (FIGURE A)
3.
Unclip plastic cover panel below the dash and remove (FIGURE B)
4.
Using the 8’ yellow/green wire provided, connect the bullet connector to
the mating bullet connector on the dual zone harness.
5.
Route the yellow/green wire through the grommet on the firewall
(FIGURE C) with a wire puller, being sure to a y moving parts thavoid an t
could damage the wire.
Interior Instructions
A B
DC
E
70-7864DZ
1. Route wire from grommet over to the under hood fuse box (FIGURE D)
2. Using a 10mm socket, remove the (2) 10mm bolts that mount the fuse box to the car. (FIGURE E)
3. Lift up on the fuse box and unclip the plastic cover on the bottom of the fuse box. (FIGURE F)
4. Locate the 16-way connector (FIGURE G) and unplug it.
5. Looking at the back of the plug where the wires go in, take a small flat blade screwdriver and
unclip the terminal lock (FIGURE H).
6. Taking the yellow/green wire with the terminal on it, insert it into the 16-way plug at the location
pictured (FIGURE I); the terminal will only lock in one way.
7. Snap the terminal lock back down and reinsert plug into the back of the fuse box.
8. Reinstall plastic cover and bolt fuse box back down.
9. Be sure to protect the yellow/green wire under the hood with split loom.
Under Hood Instructions
F
H I
G
Locking clip on 16-way plug
Front of car
16-way plug to
be removed


Specyfikacje produktu

Marka: Metra
Kategoria: nieskategoryzowany
Model: 70-7864DZ

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Metra 70-7864DZ, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany Metra

Metra

Metra 99-7382HG Instrukcja

17 Września 2024
Metra

Metra 99-3410 Instrukcja

17 Września 2024
Metra

Metra 99-7397B Instrukcja

17 Września 2024
Metra

Metra 99-7421 Instrukcja

17 Września 2024
Metra

Metra 99-8725B Instrukcja

17 Września 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024