Instrukcja obsługi Merlin 6-IN-1 DIY Educational Solar Toy Kit

Merlin Zabawki 6-IN-1 DIY Educational Solar Toy Kit

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Merlin 6-IN-1 DIY Educational Solar Toy Kit (13 stron) w kategorii Zabawki. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/13
1
Tools you may need:
Diagonal Cutter
Scissors
Pencil
Instructions:
For the assembly of all the different toys in this product two items
need to be assembled first. The Gearbox and the Solar Module.
Hint: Use a small side cutter to remove the individual pieces from
the main plastic assembly. Also remember to cut off the burr to
make a smoother edge.
1). Gearbox:
The gearbox drives the different toys.
a) Start by fitting the motor in its slot as per figure
1 and 2. Be careful to not put the motor in skew it can
damage the plastic parts.
6-in-1 DIY Educational Solar Toy Kit
Thank you for purchasing this Merlin Product. Please read the
instruction manual carefully before using the product.
The documentation provided will allow you to fully enjoy all the
features this unit has to offer.
Please save this manual for future reference.
The following items are enclosed in the box. Please note that this
product contains small plastic items that can easy be swallowed
by children. Adult supervision is recommended when having
children assemble this product.
Aditional recycled items required for assembly
of different toys:
Colored Box
Gear ( Orange )
Gear with Shaft ( Purple )
Motor with Connectors
Adhesive Tape
Eyes
Rubber Band Rubber Belt
Wing
Black Push
Red
Sponge
Solar Panel
Round Shaft
Gear with Shaft ( Green )
2
b) Now place the black and red terminals in their
positions and route the wires.
c) Slide the gears into their places as show in figure
4, 5. Lock them in place by putting on the lid like
shown in fig 6.
d) Add the two side covers to complete the gearbox.
The final product should look like figure 8.
2) Solar Module:
The Solar module provides power to the gearbox and makes the
toy come alive.
a) Place the adhesive pads (P8) on plastic module
(A16) and then place the solar cell (P6) onto it. Be
careful to feed the wires through the gap provided.
Remove the protective film that covers the solar cell.
b) The final step in the assembling the solar module is
removing the ends off of the wires from the solar
module. The wires are already partially stripped but
left in place for safety. While holding the wire and
the stripped piece twist the stripped piece and
gently pull it off. It should come off easily. Remove
both pieces of stripped ends.
3) Merging of the Solar and Gearbox Modules:
Now that the Gearbox and Solar Modules are completed
we can put them together and start making some of the
toys.
a) It is very important to orientate the gearbox module
before starting this process. In the lower right corner of
the gearbox is a directional arrow pointing to the right.
Have this arrow on your righthand side when performing
this.
b) Observe the (+) and (-) symbols of the gearbox
module. Line up the green wire to the (-) terminal and
the white wire to the (+) terminal of the gearbox module.
c) Bend over the spring terminal on the gearbox module
and insert the wires (remember to observe the correct
colors) through them to protrude out the other side.
Release the spring terminal gently. The wires from the
solar module should be securely in place to form a good
connection. If they are loose repeat the process until
they are firmly in place. Ensure that the wires don’t
touch as this will cause a short circuit and the motor will
not turn.
Black
Red
Top View
Solar Module Assembly
White
Green Side View
Completed
Side View
3
d) The completed Solar and Gearbox Modules should look like
the picture below. If everything is properly assembled the main
gear will turn when it is taken into the sunlight.
Different Toy Assembly Instructions:
1. CD Racer.
This Toy uses some old unused CD or DVD discs to build.
a) Start by assembling the parts as shown in figure
1 – 3.
b) Connect the Solar module to the Gearbox making careful
note of the polarity of the wires and orientation of the Gearbox.
After this assembly add the brackets that hold the CD wheels in
place.
c) Assemble the wheel bushes and add on the CD to form the
Solar Module Green
White
CONNECT
GREEN WIRE
Completed
Wires should not Touch each Other.
GREEN
GREEN
CD Racer: Assembly and Play
Recycled Parts Required
PUSH PUSH
WHITE WIRE
Gear Box
Green
Green
GREEN WIRE CONNECT
CONNECT
WHITE WIRE
White
White
Solar
Module
Part
Part
WHITE
CONNECT
Gear Box
How To The Gear Box
Notice: Find and make sure correct direction of “ “ on gearbox rst,
it would help you to install the parts correctly

Specyfikacje produktu

Marka: Merlin
Kategoria: Zabawki
Model: 6-IN-1 DIY Educational Solar Toy Kit

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Merlin 6-IN-1 DIY Educational Solar Toy Kit, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Zabawki Merlin

Merlin

Merlin 6-IN-1 DIY Educational Solar Robot Kit Instrukcja

4 Października 2024
Merlin

Merlin 6-IN-1 DIY Educational Solar Toy Kit Instrukcja

4 Października 2024

Instrukcje Zabawki

Najnowsze instrukcje dla Zabawki

Lego

Lego Raceway Rider Instrukcja

13 Października 2024
Lego

Lego Dora Club Co-Pack Instrukcja

13 Października 2024
Lego

Lego Puppy Playground Instrukcja

11 Października 2024
Lego

Lego Value Pack Star Wars Instrukcja

10 Października 2024
Ikea

Ikea DUKTIG 505.892.24 Instrukcja

9 Października 2024
Ikea

Ikea SKOGSDUVA 805.786.72 Instrukcja

9 Października 2024
Hasbro

Hasbro Furby Instrukcja

9 Października 2024
Kogan

Kogan KARDONFRENA Instrukcja

9 Października 2024
Mega Bloks

Mega Bloks Despicable Me - Micro Action Figures Series 10 Instrukcja

9 Października 2024
Mega Bloks

Mega Bloks Buildable Minions Blind Packs Series III Instrukcja

9 Października 2024