Instrukcja obsługi Megger TDR500/3
Megger
Meetapparatuur
TDR500/3
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Megger TDR500/3 (18 stron) w kategorii Meetapparatuur. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/18
Page 1 1 of
M
TDR1000/3
TDR1000/3P
CFL510G
TDR500/3
Time Domain Reflectometers
User Manual
Page 3 3 of
G SAFETY WARNINGS
■ Safety warnings and precautions must be read and understood before the instrument is used. All Safety warnings and
precautions must be observed during use.
■ The circuit under test must be switched off, de energised, securely isolated - and proved safe before test connections are
made.
■ Use the correct lead se the Megger fused lead set must be used. Refer to the Test Lead selection t. On power systems page
in this user guide to identify the correct lead set.
■ The operator must verify that the circuit is safe before testing and take the appropriate precautions.
■ Ensure that hands remain behind guards of probes/clips when testing.
■ The instrument should not be used if any part of it is damaged. Also all test leads, probes and crocodile clips must be in
good order, clean and with no broken or cracked insulation.
■ Disconnect the test leads before removing the battery cover. The battery cover must be in place whilst conducting tests.
■ This product contains no user service parts.
■ All relevant safety procedures must be followed.
THE INSTRUMENT MUST ONLY BE USED BY SUITABLY
TRAINED AND COMPETENT PERSONS
Page 4 4 of
Symbols
The following symbols are used on this instrument
G
CAUTION: RISK OF DANGER
t
EQUIPMENT PROTECTED THROUGHOUT BY DOUBLE INSULATION OR REINFORCED
INSULATION
c
EQUIPMENT COMPLIES WITH RELEVANT EU DIRECTIVES
EQUIPMENT COMPLIES WITH AUSTRALIAN EMC REQUIREMENTS (C tick) (NOT FOR SAFETY)-
THIS EQUIPMENT SHOULD BE RECYCLED AS ELECTRONIC WASTE
Specyfikacje produktu
Marka: | Megger |
Kategoria: | Meetapparatuur |
Model: | TDR500/3 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Megger TDR500/3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Meetapparatuur Megger
22 Września 2024
17 Września 2024
Instrukcje Meetapparatuur
- Meetapparatuur Beurer
- Meetapparatuur Joy-It
- Meetapparatuur Pioneer
- Meetapparatuur Voltcraft
- Meetapparatuur Black & Decker
- Meetapparatuur Silverline
- Meetapparatuur Testo
- Meetapparatuur TFA
- Meetapparatuur Chauvin Arnoux
- Meetapparatuur Uni-T
- Meetapparatuur Dahua Technology
- Meetapparatuur Techno Line
- Meetapparatuur Perel
- Meetapparatuur Trotec
- Meetapparatuur Velleman
- Meetapparatuur Güde
- Meetapparatuur Gossen Metrawatt
- Meetapparatuur Fluke
- Meetapparatuur Greisinger
- Meetapparatuur Continental Edison
- Meetapparatuur TDE Instruments
- Meetapparatuur Bresser
- Meetapparatuur Omnitronic
- Meetapparatuur Eltako
- Meetapparatuur Hager
- Meetapparatuur Extech
- Meetapparatuur Testboy
- Meetapparatuur Kyoritsu
- Meetapparatuur Vemer
- Meetapparatuur Klein Tools
- Meetapparatuur Ridgid
- Meetapparatuur Lanaform
- Meetapparatuur Emko
- Meetapparatuur Powerfix
- Meetapparatuur ADE
- Meetapparatuur ProfiCare
- Meetapparatuur Adwa
- Meetapparatuur Amprobe
- Meetapparatuur Toolland
- Meetapparatuur Flir
- Meetapparatuur Finder
- Meetapparatuur Fantini Cosmi
- Meetapparatuur REV
- Meetapparatuur Peak
- Meetapparatuur X-Rite
- Meetapparatuur RK Technology
- Meetapparatuur Tru Components
- Meetapparatuur Delta Ohm
- Meetapparatuur Hanna
- Meetapparatuur MGL Avionics
- Meetapparatuur PCE Instruments
- Meetapparatuur UHoo
- Meetapparatuur Aerospace Logic
- Meetapparatuur SOEKS
- Meetapparatuur Apollo Ultrasonic
Najnowsze instrukcje dla Meetapparatuur
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024
22 Września 2024