Instrukcja obsługi Martin MAC Viper Quadray

Martin Ulga MAC Viper Quadray

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Martin MAC Viper Quadray (8 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
Martin MAC Viper Quadray™ Quadray Installation and DMX Control Guide 1
MAC Viper Quadray™ Module
Installation and Control Guide
Introduction
This Guide explains how to install the Martin MAC Viper Quadray™ Module, P/N 91614052, on a Martin MAC
Viper AirFX™ fixture and control the Quadray functions via DMX.
Installation takes only a few minutes. If you keep the standard components you remove when you install the
Quadray module, the Quadray components can be uninstalled and the fixture returned to standard configuration
at any time.
Warning! Follow all the safety precautions in the MAC Viper AirFX user manual and use the
manual for reference when installing the Quadray Module and using the modified product. The
user manual is supplied with fixtures, but check that you have the latest revision of the user
manual. This is available for download from the Product Support page for the MAC Viper AirFX
at www.martin.com
Warning! Disconnect the fixture from power and allow to cool for at least 2 hours and 45
minutes before starting work.
Warning! The Quadray Module must be installed by qualified professional technicians only.
Read all of this Installation Guide carefully before starting to install the module.
Important! Make sure that the front of the head does not face the sun or any other strong light
source directly for longer than a few seconds at any time. Lenses can focus the sun's rays
inside the fixture, causing internal damage and creating a possible fire risk
Important! Do not use concentrated alcohol solutions, abrasive products or solvents to clean
the components in the Quadray Module. If wiping with a soft, lint-free cloth dampened with
distilled water is not effective, damp the cloth with distilled water containing 20% isopropyl
alcohol in solution.
If you have any questions about how to install the Quadray Module or use it safely, please contact your local
Martin distributor (see www.martin.com/distributors for details) or call the Martin 24-hour service hotline on +45
8740 0000, or in the USA on 1-888-tech-180.
Software compatibility
MAC Viper AirFX firmware version 1.2.0 or later is required for operation with the Quadray Module. The latest
version of the MAC Viper AirFX firmware is available for download from the MAC Viper AirFX Product Support
page on the Martin™ website at www.martin.com
© 2013 Martin Professional A/S. Olof Palmes Allé 18, DK-8200 Aarhus N, Denmark. Information subject to change without notice. Martin
Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic
loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this installation note. The
Martin logo, the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional A/S or
its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.
P/N 35000629 Rev. C
2 Martin MAC Viper Quadray™ Module Installation and DMX Control Guide
Preparation
The Quadray Module accessory contains the following items:
• MAC Viper Quadray Module with integral wireset
• This Installation Guide
Keep the protective packaging supplied with the module for possible re-use.
Without damaging the wiring, remove the adhesive tape that is applied to avoid damage or loss during transport:
tape holds the safety wire and wireset together and retains the two screws in the module connector on the end of
the wireset.
Calibration values for each individual module are printed on a label on the module connector. Four values are
given for the four lenses . Each time you install a Quadray Module on a fixture, you must enter its L1 to L4
calibration values in the CALIBRATION menu in the fixture’s control panel. Note these values and store them for
future use when installing the module on other fixtures.
Installation procedure
Warning! Disconnect from power and allow to cool for 30 minutes before opening the head.
To install the Quadray Module on a standard Martin MAC Viper AirFX fixture:
1. Disconnect the fixture from power and allow components to cool for 30 minutes.
2. Place the fixture on a secure work surface. Tilt the head vertically upwards and apply the tilt lock.
3. See Figure 1. Remove the top head cover by loosening its Torx 25 captive retaining screws A until the screws
turn freely (the top head cover is on top of the head with the text on the back of the head facing the right way
up). Lift the front of the cover slightly away from the head, then slide the cover towards the front of the head to
release the rear of the cover. You can allow the head cover to hang on its safety wire, but for easiest access
press the cover’s safety wire retaining clip B in towards the head chassis, slide the clip down until you can
remove it, then remove the head cover completely from the fixture.
4. See Figure 2. Release the four screws from the front lens assembly, then
release the front lens safety attachment. Remove the front lens assembly
and store it for possible re-use if the fixture is returned to standard
configuration at a later time.
Figure 1: Removing the head covers
A A
B
Figure 2
Martin MAC Viper Quadray™ Quadray Installation and DMX Control Guide 3
5. See Figure 3. Line up the Quadray
Module over the head so that the
module’s safety wire will pass through
the cutout in the front of the head above
the safety wire attachment point A and
the module’s wireset will pass through
the cutout B in the opposite side of the
head.
6. Lower the Quadray Module onto the
head, making sure that it sits completely
square to the head. Do not use
excessive force. You may need to rotate
the module slightly to the left and to the
right until you can feel that it has
engaged correctly. Check also that the
safety wire and wireset are not trapped
between the module and the head.
7. See Figure 4. Fasten the module in place by tightening the four
screws on the front of the module.
8. See Figure 5. Pass the Quadray Module’s safety
cable through the hole in the head chassis and A
then into the safety wire attachment point B. Push
and slide the fastener so that it is locked into the
attachment point.
Figure 3
A
B
Figure 4
Figure 5
A
B

Specyfikacje produktu

Marka: Martin
Kategoria: Ulga
Model: MAC Viper Quadray

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Martin MAC Viper Quadray, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ulga Martin

Martin

Martin ERA 700 Performance IP Instrukcja

30 Września 2024
Martin

Martin Thrill Vertical Fogger Instrukcja

24 Września 2024
Martin

Martin Extube Instrukcja

24 Września 2024
Martin

Martin MUM Instrukcja

24 Września 2024
Martin

Martin Freekie Instrukcja

24 Września 2024
Martin

Martin P3-100 Instrukcja

23 Września 2024
Martin

Martin THRILL Multi-FX LED Instrukcja

23 Września 2024
Martin

Martin Fixture Beam Analyzer Instrukcja

22 Września 2024
Martin

Martin MAC Ultra Wash Instrukcja

22 Września 2024
Martin

Martin RUSH MH 4 Beam Instrukcja

22 Września 2024

Instrukcje Ulga

Najnowsze instrukcje dla Ulga

Goobay

Goobay 30780 Instrukcja

15 Października 2024
QTX

QTX DM-X12 Instrukcja

15 Października 2024
Livarno

Livarno IAN 94799 Instrukcja

15 Października 2024
Astro

Astro Denia Instrukcja

13 Października 2024
AFX

AFX Grace GRCP07CBBK Instrukcja

12 Października 2024
AFX

AFX Point PNTP0107L30D1BK Instrukcja

12 Października 2024
Neewer

Neewer TL97C Instrukcja

9 Października 2024
Neewer

Neewer SRP18C Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 005.824.56 Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 705.829.38 Instrukcja

9 Października 2024