Instrukcja obsługi Martin MAC 101

Martin Ulga MAC 101

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Martin MAC 101 (36 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/36
MAC 101
RGB, CT, WRM and CLD models
User manual
TM
MAC 101 CTMAC 101
MAC 101 WRMMAC 101 CLD
Dimensions
All dimensions are in millimeters
©2010-2011 Martin Professional A/S. Information subject to change without notice. Martin Professional A/S and all affiliated compa-
nies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by
the use of, inability to use or reliance on the information contained in this manual. The Martin logo, the Martin name and all other
trademarks in this document pertaining to services or products by Martin Professional A/S or its affiliates and subsidiaries are trade-
marks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries. The use of certain patents in MAC 101 products
is licensed by Color Kinetics, Inc. (see details printed on product).
P/N 35000246, Rev. G
Safety Information 3
Safety Information
The following symbols are used to identify important safety information on the product and in this manual:
Warning! Risk Group 3 (high risk) LED product according to EN 62471. Do not look into the beam at
a distance of less than 8.3 meters (27 ft. 3 inches) from the front surface of the product. Do not view
the light output with optical instruments or any device that may concentrate the beam.
This product is for professional use only. It is not for household use.
This product presents risks of severe injury or death due to fire and burn hazards, electric shock and falls.
Read this manual before installing, powering or servicing the fixture, follow the safety precautions listed
below and observe all warnings in this manual and printed on the fixture. If you have questions about how to
operate the fixture safely, please contact your Martin supplier or call the Martin 24-hour service hotline on
+45 8740 0000, or in the USA on 1-888-tech-180.
P R O T E C T I O N F R O M E L E C T R I C S H O C K
• Disconnect the fixture from AC power before removing or installing any cover or part and when not in use.
• Always ground (earth) the fixture electrically.
• Use only a source of AC power that complies with local building and electrical codes and has both
overload and ground-fault (earth-fault) protection.
• Before using the fixture, check that all power distribution equipment and cables are in perfect condition
and rated for the current requirements of all connected devices.
• Power input and throughput cables must be rated 20 A minimum, have three conductors 1.5 mm²
(16 AWG) minimum conductor size and an outer cable diameter of 5 - 15 mm (0.2 - 0.6 in.). Cables must
be hard usage type (SJT or equivalent) and heat-resistant to 90° C (194° F) minimum. In the EU the cable
must be HAR approved or equivalent.
• Use only Neutrik PowerCon NAC3FCA cable connectors to connect to power input sockets. Use only
Neutrik PowerCon NAC3FCB cable connectors to connect to power throughput sockets.
• Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other component
is damaged, defective, deformed, wet or showing signs of overheating. Do not reapply power until repairs
have been completed.
WARNING!
Read the safety precautions in this section before
installing, powering, operating or servicing this
product.
DANGER!
Safety hazard.
Risk of severe
injury or death.
DANGER!
Hazardous
voltage. Risk of
lethal or severe
electric shock.
WARNING!
Fire hazard.
WARNING!
LED light
emission. Risk of
eye injury.
WARNING!
Burn hazard. Hot
surface. Do not
touch.
WARNING!
Wear protective
eyewear.
WARNING! Refer
to user manual.

Specyfikacje produktu

Marka: Martin
Kategoria: Ulga
Model: MAC 101

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Martin MAC 101, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ulga Martin

Martin

Martin ERA 700 Performance IP Instrukcja

30 Września 2024
Martin

Martin Thrill Vertical Fogger Instrukcja

24 Września 2024
Martin

Martin Extube Instrukcja

24 Września 2024
Martin

Martin MUM Instrukcja

24 Września 2024
Martin

Martin Freekie Instrukcja

24 Września 2024
Martin

Martin P3-100 Instrukcja

23 Września 2024
Martin

Martin THRILL Multi-FX LED Instrukcja

23 Września 2024
Martin

Martin Fixture Beam Analyzer Instrukcja

22 Września 2024
Martin

Martin MAC Ultra Wash Instrukcja

22 Września 2024
Martin

Martin RUSH MH 4 Beam Instrukcja

22 Września 2024

Instrukcje Ulga

Najnowsze instrukcje dla Ulga

Goobay

Goobay 30780 Instrukcja

15 Października 2024
QTX

QTX DM-X12 Instrukcja

15 Października 2024
Livarno

Livarno IAN 94799 Instrukcja

15 Października 2024
Astro

Astro Denia Instrukcja

13 Października 2024
AFX

AFX Grace GRCP07CBBK Instrukcja

12 Października 2024
AFX

AFX Point PNTP0107L30D1BK Instrukcja

12 Października 2024
Neewer

Neewer TL97C Instrukcja

9 Października 2024
Neewer

Neewer SRP18C Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 005.824.56 Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 705.829.38 Instrukcja

9 Października 2024