Instrukcja obsługi Marshall JTM45 - 2245
Marshall
Wzmacniacze gitarowe
JTM45 - 2245
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Marshall JTM45 - 2245 (84 stron) w kategorii Wzmacniacze gitarowe. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/84
OWNER’S MANUAL
1959SLP
1987X
2245 JTM45
1962 BLUESBREAKER
WARNING! IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
WARNING:
Before going any further, make sure that
your amplier is compable with your
mains electricity supply (for 1959SLP
& 1987X only, please refer to MAINS
SELECTOR [Rear Panel Funcon #16]).
If you have any doubt, please seek
help from a qualied technician – your
Marshall dealer can help you in this
respect.
MAINS INPUT & FUSE:
The specic mains input voltage
rang that your amplier has been
manufactured for is indicated on
the rear panel of the amplier. Your
amplier is provided with a detachable
mains (power) lead, which should be
connected to the MAINS INPUT socket
on the rear panel of the amplier
(1959SLP & 1987X Rear Panel Funcon
#17, 1962 Bluesbreaker Rear Panel
Funcon #20, 2245 JTM45 Rear Panel
Funcon #17). The correct value and
type of mains fuse is specied on the
rear panel of the amplier.
NEVER aempt to bypass the fuse or t
one of the incorrect value or type.
TRANSPORTING YOUR EQUIPMENT:
Please ensure that your amplier is
switched o, unplugged from the mains
electricity supply and that all removable
cables have been disconnected from
your equipment before aempng to
move it.
IMPORTANT SET UP INFORMATION:
1. Before connecng a speaker
cabinet(s), make sure the OUTPUT
SELECTOR (1959SLP & 1987X
Rear Panel Funcon #15, 1962
Bluesbreaker Rear Panel Funcon
#18, 2245 JTM45 Rear Panel
Funcon #15) is set to the correct
impedance.
WARNING: Failure to select the correct
impedance may damage your amplier.
When connecng a speaker cabinet(s)
make sure that you use a proper speaker
cable. Never use a screened (shielded)
guitar cable for this purpose.
2. Ensure that the MAINS (power)
switch is set to the OFF posion
(Front Panel Funcon #1).
3. Connect the supplied mains (power)
lead into the MAINS INPUT rst
and then into the mains electricity
supply.
4. Ensure that the LOUDNESS or
VOLUME controls on the front
panel are set to zero (1959SLP &
1987X Front Panel Funcons #8 &
9, 1962 Bluesbreaker Front Panel
Funcons #10 & 11, 2245 JTM45
Front Panel Funcons #8 & 9).
5. Plug your guitar into an INPUT
jack socket (Front Panel Funcon:
1959SLP, 1987X & 2245 JTM45
Front Panel Funcons #10, 1962
Bluesbreaker Front Panel Funcons
#12).
6. Ensure that the STANDBY switch is
in the ‘standby’ posion (Front Panel
Funcon #2).
7. Turn the front panel MAINS switch
to the ON posion and wait for a
few minutes before going to point 8.
8. Engage the amplier by switching
STANDBY to the ON posion.
9. Turn the LOUDNESS or VOLUME
up to your preferred level and your
amplier is ready to play.
PLEASE READ THIS MANUAL CAREFULLY BEFORE
PLUGGING IN.
FOLLOW ALL INSTRUCTIONS AND HEED ALL
WARNINGS.
KEEP THESE INSTRUCTIONS.
ENGLISH
This device complies with part 15 of the FCC Rules. Operaon is subject to the
following two condions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operaon.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protecon against harmful interference in a residenal
installaon.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instrucons, may cause harmful
interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modicaons not expressly approved by the party
responsible for compliance may void the users authority to operate the equipment.
This device complies with CAN ICES-3(B)/NMB-3(B)
COMPLIANCE STATEMENT
Specyfikacje produktu
| Marka: | Marshall |
| Kategoria: | Wzmacniacze gitarowe |
| Model: | JTM45 - 2245 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Marshall JTM45 - 2245, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Wzmacniacze gitarowe Marshall
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
Inne instrukcje Marshall
14 Października 2024
9 Października 2024
1 Października 2024
30 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024
27 Września 2024