Instrukcja obsługi Marantz PM6010 OSE

Marantz odbiornik PM6010 OSE

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Marantz PM6010 OSE (10 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/10

English

FOREWORD

This section must be read before any connection is made to the mains

supply.

WARNINGS

Do not expose the equipment to rain or moisture.

Do not remove the cover from the equipment.

Do not push anything inside the equipment through the ventilation

holes.

Do not handle the mains lead with wet hands.

EQUIPMENT MAINS WORKING SETTING

Your Marantz product has been prepared to comply with the household

power and safety requirements that exist in your area.

"/N" Version product can be powered by 230 V AC only.

"/T" Version product can be powered by 230 V AC only.

This is a voltage selector (2-position or 4-position) on the rear panel of

the "/K"Version product ,.Be sure to set the voltage selector to the mains

voltage of your area before using the unit.

IMPORTANT:

This apparatus is ﬁtted with an approved moulded 13 Amp plug.

To change a fuse in this type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI approved

type.

3. Reﬁt the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off

and an appropriate plug ﬁtted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug

without a fuse is used, the fuse at the distribution board should not be

greater than 5A.

NOTE:

The severed plug must be destroyed to avoid a possible shock hazard

should it be inserted into a 13A socket elsewhere.

HOW TO CONNECT A PLUG

The wires in the mains lead are coloured in accordance with the following

code:

BLUE-"NEUTRAL" ("N")

BROWN-"LIVE" ("L")

1. The BLUE wire must be connected to the terminal which is marked

with the letter "N" or coloured BLACK.

2. The BROWN wire must be connected to the terminal which is marked

with the letter "L" or coloured RED.

3. Do not connect either wires to the earth terminal in the plug which is

marked by the letter "E" or by the safety earth symbol or coloured

green or green-and-yellow.

Before replacing the plug cover, make certain that the cord grip is

clamped over the sheath of the lead - not simply over the two wires.

Recording and playback of any material may require consent. For further

information refer to the following:

— Copyright Act 1956

— Dramatic and Musical Performers Act 1958

— Performers Protection Acts 1963 and 1972

— any subsequent statutory enactments and orders

ABOUT THIS USER GUIDE

Refer to the Figures on the pages at the rear of this user guide. The call

out numbers on the Figures correspond to those found in the text. All

references to the connections and controls that are printed in BOLD type

are as they appear on the unit.

PRECAUTIONS

The following precautions should be taken when operating the equip-

ment.

GENERAL PRECAUTIONS

When setting the equipment ensure that:

— the ventilation holes are not covered

— air is allowed to circulate freely around the equipment

— it is on a vibration free surface

— it will not be exposed to interference from an external source

— it will not be exposed to excessive heat, cold, moisture or dust

— it will not be exposed to direct sunlight

— it will not be exposed to electrostatic discharges

In addition, never place heavy objects on the equipment.

If a foreign body or water does enter the equipment, contact your nearest

dealer or service center.

Do not pull out the plug by pulling on the mains lead, hold the plug.

It is advisable when leaving the house, or during a thunderstorm, to

disconnect the equipment from the mains supply.

CONNECTIONS

(Figure 1)

CONNECTION OF TUNER

Connect the output jacks of your stereo tuner to the jacks of thisTUNER

unit.

CONNECTION OF COMPACT DISC PLAYER

Connect the output jacks of your CD player to the jacks of this unit.CD

CONNECTION OF TURNTABLE

Connect the L (Left) output cord of the turntable to the "L" PHONO jack

of this unit, and connect the R (Right) output cord to the "R" PHONO jack.

Also be sure to connect the turntable's grounding wire to the jackGND

of this unit. The jack does not have to be connected if the turntableGND

is not provided with a grounding wire.

CONNECTION OF TAPE DECK

Connect the (recording input) jacks of the tape deck to the jacksIN OUT

of this unit, and connect the (playback output) jacks of the tapeOUT

deck to the jacks of this unit.IN

CONNECTION OF SPEAKER SYSTEMS

This unit is equipped with a sets of terminals.SPEAKER SYSTEM

• The speakers in the speaker system should have an impedance

between 8 and 16 ohms. If speakers with an impedance of less than

8 ohms are connected, the protection circuitry may be activated

during play.

• Connect the Right channel speaker to the terminals, and the LeftR

channel speaker to the terminals.L

• The output terminals have positive (r: Red) and negative (s: Black)

polarity, and each speaker also has the same polarity (r and s). When

connecting the speaker, be sure to connect the terminals with the

same polarity (r with r, s with s).

NOTE:

Turn the knobs on the speaker terminals by hand. (Do not use a tool

to turn the knobs.)

CONTROLS, CONNECTORS, AND INDICATORS

(Figure 2)

AAA AUX INPUT JACKS

These are auxiliary input jacks which can be used to connect the audio

outputs of AV components such as TV multiplex/stereo audio tuners,

VCRs, and laserdisc players.

BBB TUNER INPUT JACKS

Connect the output jacks of the tuner to these jacks.

CCCCC CD PLAYER INPUT JACKS

Connect the output jacks of a Compact Disc player to these jacks.

DDD PHONO INPUT JACKS

Connect the output jacks of a turntable to these jacks.

English

GND (GROUND) TERMINAL

Connect the grounding wire from the turntable to this terminal.

FFFFF TAPE CD-R/MD IN/OUT JACKS

Connect the play (output) jacks and record (input) jacks of tape decks

to these jacks.

Up to three tape decks can be connected.

NOTE:

When a surround processor or graphic equalizer is used, it must be

connected to the TAPE jacks.

GGGGG SPEAKER SYSTEMS

Connect your speaker system to these terminals.

HHH REMOTE CONTROL (BUS) TERMINALS

Another item of audio equipment with a remote control (bus) terminal can

be connected to these terminals by using a special-purpose cable. The

bus OUT terminal is used to send signals to another item of equipment.

The bus IN terminal is used to receive signals from another item of

equipment.

III POWER CORD

Connect to a household power outlet.

qqqqq POWER SWITCH

Pressing once switches the power , and pressing again switches itON

OFF. The indicator lights when the switch is , andPOWER POWER ON

go out when the switch is .POWER OFF

wwwww INPUT SELECTOR

Selects the program source to be recorded or played from the PHONO,

CD TUNER AUX, , .

eVOLUME CONTROL

Adjusts the volume level. Turn the knob clockwise to increase the

volume.

You can also operate the ampliﬁer with a remote control unit.

rBALANCE CONTROL

Turn the knob to correct an unbalanced program source such as stereo

broadcast or to vary the output level of the left or right channel.

Note that, if the control is turned fully in one direction, theBALANCE

sound will not be heard from the speaker on the other side.

ttttt TAPE CD-R/MD SWITCHES

Press one of these switches to monitor the playback sound of a tape

deck connected to the rear panel of this unit.

When the CD-R/MD switch is pressed, this unit automatically enters the

tape dubbing mode, the COPY CD-R ﬁTAPE indicator lights, and the

playback signal of CD-R or MD can be copied onto tape deck.

Set both of the switches to OFF when the CD-R or MD, tape decks are

not to be played.

For details, refer to "TAPE DECK OPERATION".

yyyyy SOURCE DIRECT SWITCH

When this switch is pressed, the audio signal is supplied directly to the

volume control circuitry (the signal is directed through the minimum

required path to improve the reproduction of high-quality sources).

NOTE:

When this switch is ON, the settings of the tape monitor switches,

and balance control are ignored.

While this switch is depressed, recording, playback, or dubbing of

tapes cannot be carried out even when a tape monitor switch is

pressed.

uuuuu IR SENSOR

The remote sensor receives the infrared commands from the remote

control unit. When an infrared signal is received from the remote control

unit. The remote control unit must always be pointed directly at the

remote sensor.

iMUTING INDICATOR

Light up when the button in the remote control unit is pressed.MUTING

NOTE:

Be sure to check the control setting before pressing thisVOLUME

switch to cancel muting, If the muting is canceled while the volume

setting is high, the speakers could be damaged.

ooo PHONES JACK

Insert the standard phone plug of the headphones into this jack.

OPERATION PROCEDURES

TO PLAY AN ANALOG RECORD

1. Set the switch to .INPUT SELECTOR PHONO

2. Play a record on the turntable.

3. Adjust the volume with the control.VOLUME

NOTES:

• Set the control to the minimum position before placing theVOLUME

stylus on the record or before replacing the cartridge.

• Do not apply shock or vibration to the turntable during play, as this

may cause the stylus to jump and the analog record to be damaged.

• If the turntable is installed too close to the speakers, the volume may

not be able to be increased to a high level due to howling.

• Do not switch the power OFF while the stylus is on the record surface.

TO LISTEN TO FM/AM BROADCASTS

1. Set the switch to .INPUT SELECTOR TUNER

2. Tune in the desired station on the tuner.

3. Adjust the volume with the control.VOLUME

TO PLAY A COMPACT DISC

1. Set the switch to .INPUT SELECTOR CD

2. Play a CD on the CD player.

3. Adjust the volume with the control.VOLUME

TO PLAY A COMPONENT CONNECTED TO AUX JACKS

The component connected to the AUX jacks on the rear panel can be

played as follows.

1. Set the switch to .INPUT SELECTOR AUX

2. Play the component connected to the selected input.

3. Adjust the volume with the control.VOLUME

TAPE CD-R/MD SOURCE DI RECT

INT EG RAT ED AM PL IFI ER PM 60 10 OS E

TA P E CD-R / MD

MUT E

MIN MAX

L R

CO P Y

CD- R> T A P E

PHONO TU NER

AUX

INPUT SE LECTOR VOLUME

BALA NCE

POWER O N/OFF PHONES

ON OFFON OFFON OFF

2 Operate each equipment to start play.

1 3

English

TAPE DECK (CD-R/MD) OPERATION

TAPE (CD-R/MD) PLAYBACK

1. Press the or switch CD-R/MD TAPE A. The indicator above the

switch will light up.

2. Play a prerecorded tape on the tape deck (or CD-R).

3. Adjust the volume with the VOLUME control B.

NOTES:

• Set the CD-R/MD TAPE switches to OFF when a tape is not to be

played.

• The tape can be played regardless of the setting of the INPUT

SELECTOR C.

TAPE RECORDING

The playback sound of a program source component, such as a

turntable, a tuner, or a CD player, can be recorded on tape as follows.

1. Set the switch to select the program source toINPUT SELECTOR C

be recorded.

2. Play the program source.

3. Operate the tape deck (or CD-R) to record the playback sound on

tape.

NOTE:

Playback and recording onto tape decks is not possible while the

SOURCE DIRECT switch is pressed in.

TAPE MONITORING

When a three-head tape deck is connected to the jacks, the soundTAPE

recorded on tape can be monitored through the speakers by pressing

the TAPE monitor switch . In this case, the tape deck must beA

connected to this unit via both recording and playback connection

cords.

NOTE:

When the tape deck is a two-head system, the recorded sound cannot

be monitored even when the switch is pressed. InCD-R/MD TAPE A

this case, however, the sound of the program source being recorded

can be monitored.

When the program source selected by the INPUT SELECTOR is to be

recorded onto the tape deck connected to the jacks, do not pressTAPE

the CD-R/MD switch.

If the switch is pressed, the unit enters CD-R/MD CD-R ﬁTAPE copy

mode.

DUBBING OF PRERECORDED TAPES

If you connect two tape decks to this unit, the contents of a prerecorded

tape can be copied onto another tape. For example, you can record only

the desired tunes on a tape containing an FM radio program onto another

tape, or you can copy the contents of an open-reel tape onto a cassette

tape. When the switch is pressed, this unit automatically enterCD-R/MD

the CD-R/MD (TAPE 2) ﬁ TAPE (TAPE 1) copy mode, and the playback

signal of tape deck 2 can be copied onto tape deck 1.

NOTES:

• When both of the and switches are pressed in. TheCD-R/MD TAPE

sound recorded from CD-R/MD to tape deck can be monitored

through the speakers.

• During dubbing, the program source selected by the INPUT SELEC-

TOR switch cannot be listened to.

• When the program source selected by the switchINPUT SELECTOR

is recorded simultaneously by the CD-R (or MD) and tape deck, the

sound recorded by CD-R or MD cannot be monitored. If the CD-R/MD

switch is pressed, the signal of CD-R/MD will be output to tape deck.

• When a component such as a surround processor or graphic

equalizer is to be used, connect the component to the TAPE IN/OUT

jacks and press the switch.TAPE

TAPE CD-R/MD SOURCE DI REC T

INT EG RAT ED AM PL IFI ER PM 60 10 OS E

TA P E CD-R / MD

MUT E

MIN MAX

L R

PHONO TU NER

AUX

INPUT SE LECTOR VOL UME

BALA NCE

POWER O N/OFF PHONE S

ON OFFON OFFON OFF

C B

Control used for operating the tape deck.

CO P Y

CD- R> T A P E

Switch Setting

Indicators

Speaker Output

CD-R/MD OUT Jack Output

TAPE OUT Jack Output

CD-R/MD TAPE TAPE

CD-R/MD CD-R/MD

Source selected by INPUT

SELECTOR

Source selected by INPUT

SELECTOR

Source selected by INPUT

SELECTOR

Source selected by INPUT

SELECTOR

Source selected by INPUT

SELECTOR

Source selected by INPUT

SELECTOR

Source selected by INPUT

SELECTOR

CD-R/MD

OFF

TAPE COPY

CD-R/MD

TAPE COPY

CD-R/MD

TAPE COPY

CD-R/MD

TAPE COPY

TAPE

OFF

CD-R/MD

TAPE

OFF

CD-R/MD

OFF

TAPE

CD-R/MD

TAPE

TAPE MONITOR SWITCH OPERATION CHART

Specyfikacje produktu

Marka:	Marantz
Kategoria:	odbiornik
Model:	PM6010 OSE

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Marantz PM6010 OSE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje odbiornik Marantz

Marantz SR-8000 Instrukcja

15 Stycznia 2025

Marantz Model 60n Instrukcja

1 Stycznia 2025

Marantz MODEL M4 Instrukcja

9 Października 2024

Marantz SR-7200 Instrukcja

6 Października 2024

Marantz SR-19 Instrukcja

26 Września 2024

Marantz NR1608 Instrukcja

26 Września 2024

Marantz NR1510 Instrukcja

23 Września 2024

Marantz VS3003 Instrukcja

10 Września 2024

Marantz PM5004/ZIL Instrukcja

9 Września 2024

Marantz Melody Media MCR503 Instrukcja

8 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

AKAI AM-32 Instrukcja

15 Stycznia 2025

Peavey CKd 608 Instrukcja

15 Stycznia 2025

OSD Audio Nero HTX4150 Instrukcja

14 Stycznia 2025

S.M.S.L PA200 Instrukcja

14 Stycznia 2025

Pyle PFMRA340BB.5 Instrukcja

13 Stycznia 2025

Wavtech link700.4plus Instrukcja

13 Stycznia 2025

Behringer NU6000DSP Instrukcja

12 Stycznia 2025

Denon DRA-935R Instrukcja

12 Stycznia 2025

Kenwood KMM-BT508DAB Instrukcja

12 Stycznia 2025

Boss DD-500 Instrukcja

12 Stycznia 2025