Instrukcja obsługi Makita PO6000C

Makita Maszyna do polerowania PO6000C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita PO6000C (8 stron) w kategorii Maszyna do polerowania. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
INSTRUCTION MANUAL
Random Orbit Polisher
PO5000C
PO6000C
ENGLISH: Original instructions
DOUBLE INSULATION
Read before use.
2 ENGLISH
SPECIFICATIONS
Model: PO5000C PO6000C
Pad diameter 125 mm 150 mm
Orbits per minute 0 - 6,800 min-1
Overall length 451 mm
Net weight 2.8 kg
Safety class /II
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydifferfromcountrytocountry.
• WeightaccordingtoEPTA-Procedure01/2003
Symbols
The following show the symbols used for the equip-
ment. Be sure that you understand their meaning before
use.
Read instruction manual.
DOUBLE INSULATION
Only for EU countries
Do not dispose of electric equipment
together with household waste material! In
observance of the European Directive, on
WasteElectricandElectronicEquipment
and its implementation in accordance with
national law, electric equipment that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.
Intended use
The tool is intended for polishing.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to 60745-2-4:
Model PO5000C
Sound pressure level (LpA ) : 81 dB(A)
Sound power level (LWA) : 92 dB (A)
Uncertainty(K):3dB(A)
Model PO6000C
Sound pressure level (LpA ):83dB(A)
Sound power level (LWA) : 94 dB (A)
Uncertainty(K):3dB(A)
WARNING: Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to 60745-2-4:
Model PO5000C
Workmode:polishing
Vibration emission (a
h, AP) : 6.5 m/s2
Uncertainty (K) : 1.5 m/s
2
Model PO6000C
Workmode:polishing
Vibration emission (a
h, AP) : 7.0 m/s2
Uncertainty (K) : 1.5 m/s
2
NOTE:
The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING: The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING: Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings and
all instructions. Failure to follow the warnings and
instructionsmayresultinelectricshock,reand/or
seriousinjury.
3 ENGLISH
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions.Waterenteringapowertoolwillincrease
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
6.
If operating a power tool in a damp location is unavoid-
able, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
7. Use of power supply via an RCD with a rated
residual current of 30 mA or less is always
recommended.
Personal Safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
powertoolsmayresultinseriouspersonalinjury.
2.
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriateconditionswillreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
yourngerontheswitchorenergisingpowertools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts.Looseclothes,jewel-
lery or long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
powertoolwilldothejobbetterandsaferatthe
rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Follow instruction for lubricating and chang-
ing accessories.
3. Keep handles dry, clean and free from oil and
grease.
Polisher safety warnings
1. This power tool is intended to function as a
polisher. Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instruc-
tionslistedbelowmayresultinelectricshock,re
and/orseriousinjury.

Specyfikacje produktu

Marka: Makita
Kategoria: Maszyna do polerowania
Model: PO6000C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Makita PO6000C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do polerowania Makita

Makita

Makita PO5000C Instrukcja

26 Września 2024
Makita

Makita DPV300Z Instrukcja

2 Września 2024
Makita

Makita PW5000C Instrukcja

30 Sierpnia 2024
Makita

Makita PO6000C Instrukcja

18 Sierpnia 2024
Makita

Makita DPO600Z Instrukcja

18 Sierpnia 2024
Makita

Makita DPO600RTE Instrukcja

15 Sierpnia 2024

Instrukcje Maszyna do polerowania

Najnowsze instrukcje dla Maszyna do polerowania

Speed & Go

Speed & Go AP 250 E Instrukcja

28 Grudnia 2024
Speed & Go

Speed & Go PM 241 Instrukcja

28 Grudnia 2024
Bavaria By Einhell

Bavaria By Einhell Bavaria BPM 500 Instrukcja

26 Grudnia 2024
Royal Catering

Royal Catering RCGP-2.0A Instrukcja

24 Grudnia 2024
Total

Total TAPLI2001 Instrukcja

17 Grudnia 2024
Total

Total TP1141806 Instrukcja

17 Grudnia 2024
Black & Decker

Black & Decker G650 Instrukcja

8 Października 2024
Worx

Worx WX856.9 Instrukcja

5 Października 2024
Robust

Robust RB-PO 110 Instrukcja

3 Października 2024
RIKON

RIKON 31-200 Instrukcja

2 Października 2024