Instrukcja obsługi Makita GA7071X1

Makita nieskategoryzowany GA7071X1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita GA7071X1 (20 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/20
INSTRUCTION MANUAL
Angle Grinder
GA7070
GA7071
GA9070
GA9071
ENGLISH: Original instructions
DOUBLE INSULATION
Read before use.
2 ENGLISH
SPECIFICATIONS
Model: GA7070 GA7071 GA9070 GA9071
Wheel diameter 180mm 230mm
Max. wheel thickness 7.2mm 6.5mm
Spindle thread M14 or 5/8″ (country specic)
Rated speed (n) 8,500min-1 6,600min-1
Overall length 506mm
Switch handle Bar type D type Bar type D type
Net weight 6.1 - 6.6 kg 6.2 - 6.7 kg 6.3 - 8.5 kg 6.4 - 8.5 kg
Safety class /II
• Due to our continuing program of research and development, the specications herein are subject to change
without notice.
• Specications may di󰀨er from country to country.
• The weight may di󰀨er depending on the attachment(s). The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
Wear safety glasses.
DOUBLE INSULATION
Only for EU countries
Due to the presence of hazardous compo-
nents in the equipment, used electrical and
electronic equipment may have a negative
impact on the environment and human health.
Do not dispose of electrical and electronic
appliances with household waste!
In accordance with the European Directive
on waste electrical and electronic equipment
and its adaptation to national law, used
electrical and electronic equipment should
be collected separately and delivered to
a separate collection point for municipal
waste, operating in accordance with the
environmental protection regulations.
This is indicated by the symbol of the
crossed-out wheeled bin placed on the
equipment.
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745-2-3:
Model GA7070
Sound pressure level (L
pA) : 92 dB(A)
Sound power level (L
WA) : 103 dB (A)
Uncertainty (K) : 3 dB(A)
Model GA7071
Sound pressure level (L
pA) : 91 dB(A)
Sound power level (L
WA) : 102 dB (A)
Uncertainty (K) : 3 dB(A)
Model GA9070
Sound pressure level (L
pA) : 91 dB(A)
Sound power level (L
WA) : 102 dB (A)
Uncertainty (K) : 3 dB(A)
Model GA9071
Sound pressure level (L
pA) : 91 dB(A)
Sound power level (L
WA) : 102 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during actual
use of the power tool can di󰀨er from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING: Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
o󰀨 and when it is running idle in addition to the
trigger time).
3 ENGLISH
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN60745-2-3:
Model GA7070
Work mode: surface grinding with normal side grip
Vibration emission (ah, AG) : 6.4 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: surface grinding with anti vibration side grip
Vibration emission (ah, AG) : 6.0 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: disc sanding with normal side grip
Vibration emission (ah, DS) : 4.6 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: disc sanding with anti vibration side grip
Vibration emission (ah, DS) : 4.6 m/s2
Uncertainty (K) : 1.5 m/s2
Model GA7071
Work mode: surface grinding with normal side grip
Vibration emission (ah, AG) : 5.1 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: surface grinding with anti vibration side grip
Vibration emission (ah, AG) : 5.3 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: disc sanding with normal side grip
Vibration emission (ah, DS) : 3.4 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: disc sanding with anti vibration side grip
Vibration emission (ah, DS) : 3.9 m/s2
Uncertainty (K) : 1.5 m/s2
Model GA9070
Work mode: surface grinding with normal side grip
Vibration emission (ah, AG) : 4.9 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: surface grinding with anti vibration side grip
Vibration emission (ah, AG) : 4.8 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: disc sanding with normal side grip
Vibration emission (ah, DS) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
Work mode: disc sanding with anti vibration side grip
Vibration emission (ah, DS) : 2.6 m/s2
Uncertainty (K) : 1.5 m/s2
Model GA9071
Work mode: surface grinding with normal side grip
Vibration emission (ah, AG) : 5.1 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: surface grinding with anti vibration side grip
Vibration emission (ah, AG) : 4.9 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: disc sanding with normal side grip
Vibration emission (ah, DS) : 3.1 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: disc sanding with anti vibration side grip
Vibration emission (ah, DS) : 3.1 m/s2
Uncertainty (K) : 1.5 m/s2
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING: The vibration emission during
actual use of the power tool can di󰀨er from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING: Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
o󰀨 and when it is running idle in addition to the
trigger time).
WARNING: The declared vibration emission
value is used for main applications of the power tool.
However if the power tool is used for other applica-
tions, the vibration emission value may be di󰀨erent.
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, re and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.

Specyfikacje produktu

Marka: Makita
Kategoria: nieskategoryzowany
Model: GA7071X1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Makita GA7071X1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Makita

Makita

Makita DJS101 Instrukcja

16 Września 2024
Makita

Makita DST221 Instrukcja

25 Maja 2024
Makita

Makita DKP181 Instrukcja

21 Maja 2024
Makita

Makita CL001GD225 Instrukcja

19 Maja 2024
Makita

Makita DFT022F Instrukcja

19 Maja 2024
Makita

Makita 8381D Instrukcja

17 Maja 2024
Makita

Makita GA7071X1 Instrukcja

16 Maja 2024
Makita

Makita DST112 Instrukcja

14 Maja 2024
Makita

Makita DCM501 Instrukcja

13 Maja 2024
Makita

Makita UR012G Instrukcja

12 Maja 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact Qualite QL-3560-LED Instrukcja

4 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact Forever Ready Cool FRC-24-LED Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact Varipole Drop Ceiling Adapter Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024