Instrukcja obsługi Mac Tools BB2000


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mac Tools BB2000 (4 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
PageSection - MV27 - 1
Form 822789JULY - 2004
VACUUM BRAKE BLEEDER
MODEL BB2000
USERS MANUAL
FOR CUSTOMER SERVICE, PLEASE CONTACT
1-800-MAC-TOOLS
SPECIFICATIONS
Reservoir Capacity: 1.9 quarts
(1.8 liters)
Bleed Tube Length: 72 in. (1830 cm)
Evac Tube Length: 48 in. (1220 cm)
Working Pressure: 60 to 150 psi
(4.1 to 10.3 bar)
Air Consumption: 4.3 scfm @ 90 psi
(2.0 l/s @ 6.2 bar)
Vacuum
@ 30 psi (2.0 bar): 6.5 in. hg (22 kpa)
@ 60 psi (4.1 bar): 16.5 in. hg
(56 kpa)
@90 psi (6.2 bar): 26.5 in. hg
(90 kpa)
@150 psi (10.3 bar): 27 in. hg (91 kpa)
Fill Rate
@ 30 psi (2.0 bar): 24.5 oz/min
(725 ml/min.)
@ 60 psi (4.1 bar): 49.5 oz/min
(1460 ml/min.)
@90 psi (6.2 bar): 70.5 oz/min
(2095 ml/min.)
@150 psi (10.3 bar): 70.5 oz/min
(2095 ml/min.)
Page Number - 2 Form 822789
Item Part No. Description Item Part No. Description
1 822664 BLEED SCREW ADAPTER KIT 8 822705 O-RING KIT
2 822694 BLEED TUBE ASS'Y 9 822706 RESERVOIR GASKET KIT
3 822700 VALVE KIT 10 822709 MUFFLER KIT
4 822701 BASE KIT 11 822722 EVAC TUBE ASS'Y
5 822702 COUPLER SWIVEL KIT 12 822731 FLOAT KIT
6 822703 COUPLER KIT 13 822753 HOOK KIT
7 822704 VENT KIT 14 MVA6825 FLUID REFILL KIT
BRAKE BLEEDER
KIT COMPONENTS
822722
EVAC TUBE ASSY
822701
BASE KIT
822700
VALVE KIT
822703
COUPLER KIT 822704
VENT KIT
822706
RESERVOIR GASKET
KIT
822709
MUFFLER KIT
822705
O-RING KIT
822702
COUPLER SWIVEL
KIT
822731
FLOAT KIT
822694
BLEED TUBE ASSY
MVA6825
FLUID REFILL KIT
3.0 3.0
822753
HOOK KIT
822664
BLEED SCREW
ADAPTER KIT
Page Number - 3Form 822789
Important Precautions
Always read carefully and understand instruc-
tions prior to using this equipment
Brake fluid is highly corrosive. Wear gloves and
approved safety goggles at all times, and pre-
vent contact of the fluid with painted surfaces.
Consult and follow the vehicle manufacturer’s
recommended procedures when servicing any
hydraulic system.
Do not use this unit with flammable liquids or
with fluids at temperatures above 175° Fahren-
heit (80° Celsius).
Properly dispose of old fluids, and replenish
hydraulic systems with new brake fluid from
freshly opened containers.
Do not attempt to pressurize the bleeder/evacu-
ator. It is designed for vacuum use only.
This unit is equipped with an automatic shut-off
device that will prevent fluid from entering the
compressed air stream and ejecting through the
exhaust. However, if the unit is continuously
operated when the reservoir is full, residual
pressure will allow the reservoir to completely fill
with fluid, creating the potential for spillage when
the lid is removed. To prevent this situation,
empty or turn the unit off prior to filling the reser-
voir completely full.
Principal of Operation
This unit is designed for use as a vacuum brake or
clutch bleeder, or fluid evacuator. It utilizes com-
pressed air between 60 psi (4.1 bar)and 150 psi
(10.3 bar), and a venturi system, to build vacuum in
the reservoir. By attaching the proper accessory to
the coupler located on the top of the unit, the vacu-
um can be used to drain brake fluid from a hydrau-
lic system such as the brake or clutch systems on
an automobile. It can also be used to evacuate a
variety of fluids from reservoirs including the mas-
ter cylinder or those for power steering fluid or
engine coolant.
An automatic master cylinder refill kit is included
with this unit. It is conveniently designed for use
with a standard bottle of brake fluid, to maintain an
adequate fluid level in the master cylinder while the
hydraulic system is bled. Instructions are included
with the kit for its use.
Instructions for Bleeding Brakes
IMPORTANT: This unit is designed for servicing a
variety of vehicles in a safe, convenient manner.
However, options such as load sensors or anti-lock
brakes, available on many automobiles, may
require additional steps or equipment to perform a
proper service job. The procedures below are to
serve as guidelines for the use of this equipment,
in addition to these guidelines, always follow the
manufacturers recommended procedures when
servicing each unique vehicle.
Removing old fluid from the brake master
cylinder
1. Properly park the vehicle on level ground and
turn the engine off.
2. Clean the exterior of the master cylinder and
master cylinder cap to prevent dirt from entering
the master cylinder when the cap is removed.
3. Remove the cap from the master cylinder
reservoir.
4. Connect clean, regulated (60 psi (4.1 bar) to 150
psi (10.3 bar)) compressed air to the male quick
disconnect nipple attached to the swivel air inlet,
located on one end of the vacuum bleeder
handle.
5. Connect the appropriate end of the evac tube
assembly to the female quick disconnect cou-
pler located on top of the vacuum bleeder.
6. Insert the other end of the evac tube assembly
into the master cylinder fluid reservoir, and push
the vacuum bleeder throttle forward to start the
vacuum (allow a few seconds for vacuum to
build in the bleeder reservoir before suction
occurs). While evacuating the old fluid, stir it up
to break loose and remove any sludge that has
accumulated on the bottom and walls of the
master cylinder.
7. Once all fluid is removed, turn off the bleeder
and refill the master cylinder with new manufac-
turer’s recommended brake fluid.


Specyfikacje produktu

Marka: Mac Tools
Kategoria: Nie skategoryzowane
Model: BB2000

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Mac Tools BB2000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Nie skategoryzowane Mac Tools

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane