Instrukcja obsługi L.R.Baggs M1 Active

L.R.Baggs Niesklasyfikowane M1 Active

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla L.R.Baggs M1 Active (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

I N S T A L L A T I O N M A N U A L & U S E R ' S G U I D E

L . R . B A G G S P I C K U P S

M 1 A C T I V E

4 8 3 N . F R O N T A G E R D .

N I P O M O , C A 9 3 4 4 4

W W W . L R B A G G S . C O M

tail

block

smaller

threaded

section

protrudes

1 . P A C K A G E C O N T E N T S

One (1) M1 Active pickup with battery installed

One (1) pre-wired strapjack assembly

One (1) spare battery

One (1) 3/32" Allen wrench

Two (2) spare 3/4" pole pieces

One (1) spare 3/8" pole piece

Two (2) self-stick wire clips

One (1) manual

One (1) warranty card

2 . O V E R V I E W A N D C A U T I O N S

The M1 Active magnetic pickup, with its built-in all Class A discrete preamp, features outstanding body sensitivity with great warmth and

presence. Its dual-coil design employs L.R. Baggs' exclusive patent pending Tri-Axial Dynamic Technology to produce clear, rich tones that are

resistant to feedback, noise and hum, with string and body sound all in one. A volume control is conveniently located for fingertip control. The M1

Active also features individually adjustable pole pieces with smooth, threadless tops. The M1 Active will fit guitars with sound holes larger than

3.5" that are centered beneath the strings. Ensure that this product will fit the guitar properly before installing the strapjack. The installation

procedure is very simple; however, we recommend that any woodworking (for instance, drilling a strapjack hole) be performed by a professional

dealer/installer. We do not provide advice or support for home or hobbyist woodworking.Installers: Please read the instructions carefully before

proceeding. We will not be responsible for any damageto the guitar or personal injury resulting from installation, improper installation, use or

misuse of the product.

3 . I N S T A L L A T I O N

3.1 Strapjack installation: If the guitar doesn't already have a strapjack or a

hole in the tail block, it will be necessary to drill one in order to use the

strapjack.

This jack requires a clean 1/2" hole in the tail block of the instrument. If the

guitar lacks this hole, start by placing a piece of masking tape on the outside

of the instrument over the drilling area (to avoid chipping the finish), drill a

small pilot hole in the tail block and then follow with a step drill. Now proceed

with the installation.

Remove the strap ring, retaining nut and one washer from the end of the jack.

There should still be one star locking washer, one flat washer and a nut

remaining on the jack. Bring the jack down through the sound hole into the

body and insert it into the pre-drilled hole in the tail block.

Using the internal nut (be sure to include the flat and star washers), set the

proper depth that will allow the entire smaller threaded section to protrude

from the instrument (see figure).

With the jack in place, lay the remaining washer over the threads and attach the external retaining nut until it's tight. Finish by attaching the strap

ring (it should cover the retaining nut and washer). Note that asserting too much pressure may crack the finish.

3.2 Pickup installation: Be sure there's a battery inserted into the battery

holder. Then plug the strapjack harness

into the pickup.

Now loosen the clamp screws on either end of the pickup's top plate until the

clamps are open enough to accommodate the guitar's top thickness. Then

slide the pickup into the sound hole and tighten the screws. Be sure to secure

the wire with the two self-stick wire clips provided so that it does not hit the

inside of the guitar during stage movement.

Tighten the screws snugly, but don't overdo it -- this can damage the pickup

or guitar finish. If you are concerned about the possibility of the M1 Active

damaging the instrument's finish, consider applying thin cork pads (not included) between the clamp and guitar. However, note that the clamps

have been lef t unpadded to improve coupling between the pickup and guitar body. Because the M1 Active reads the top resonances that provide

depth and warmth, using cork pads may dampen this sensitivity and adversely affect the pickup's responsiveness.

4 . U S E R ' S G U I D E

4.1 Plugging in: The M1 Active will plug into practically anything with good results. If you want EQ or use a direct box, our Para D.I. provides both

EQ and DI features. Plugging in turns the circuit on and unplugging turns the circuit off. If you want your battery to last a good long time,

remember to unplug when you're done.

4.2 Volume control: Yes.

4.3 Replacing the battery: The battery life of the M1 Active is a very long 1000 hours, or about 250 gigs. If you're plugged in 20 hours a week,

you'll need to replace your battery once a year. If your battery is going dead you will start to hear some distortion. From the time you hear audible

distortion until it's too late, you have several gigs to replace the battery. Press on the center tab over the battery to dislodge the battery. You may

need to use a pencil or other tool to press the tab. Lift the battery out from the slots in the side of the pickup, then slide and snap a new one in.

Observe polarity. You should be able to read the CR2032 and the "+" designator when the battery is properly installed. These batteries are

available at all large drugstores, and sometimes at supermarkets.

4.4 Experimenting with pole piece heights: The pole pieces on the M1 Active are preset (for bronze acoustic strings ), but this is just a starting

place. They are adjustable with the 3/32" Allen wrench to obtain the optimum balance and tone. The height of the pole pieces relative to the

strings will have a profound effect on the sound and balance of the pickup. Raising the pole pieces will increase the output of the strings;

lowering them will decrease the output. For the most powerful and articulate sound, we recommend setting the pole pieces closer to the strings.

However, if they are too close, they will interfere with the strings' movement and produce a percussive clacking noise. Lowering the pole pieces

will deemphasize the strings and emphasize the body sound. We have provided two additional 3/4" pole pieces for use in the B and little E string

positions with nickel or electric guitar strings, and one spare 3/8" pole piece for use with acoustic sets that have an unwound "G" string. When

adjusting the pole pieces downward you will meet additional resistance when you reach the bottom of the adjustment range. Do not force the

pole pieces any further! This could damage the pickup permanently.

4.5 Mixing with other sources: The M1 Active is intended to provide a complete sound from a single pickup. However , you may still want to pair

it with another transducer. We have provided for this. The pre-wired strapjack harness has dual output capability. You can connect the output wire

from a mini-mic or another transducer to the ring terminal of this jack. Then run a stereo cord to the L.R. Baggs Mixpro or your favorite outboard

gear. As with all two-pickup setups, you should experiment with relative phase between pickups if possible. Two sources will often mix much

better in one phase than the other.

4 . S P E C I F I C A T I O N S

Battery type: CR2032

Battery life: 1000+ hours

Current consumption: 135 uA

Preamp signal to noise: -78dB unweighted

Output level: -10dB

Output impedance: 800 ohms

Specyfikacje produktu

Marka:	L.R.Baggs
Kategoria:	Niesklasyfikowane
Model:	M1 Active

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z L.R.Baggs M1 Active, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane L.R.Baggs

L.R.Baggs Session VTC Instrukcja

24 Września 2024

L.R.Baggs FIVE.O Instrukcja

24 Września 2024

L.R.Baggs Para Acoustic D.I. Instrukcja

24 Września 2024

L.R.Baggs M80 Instrukcja

24 Września 2024

L.R.Baggs M1 Instrukcja

24 Września 2024

L.R.Baggs Stage Pro Element Instrukcja

24 Września 2024

L.R.Baggs Stage Pro Anthem Instrukcja

24 Września 2024

L.R.Baggs M1 Active Instrukcja

23 Września 2024

L.R.Baggs Gigpro Instrukcja

23 Września 2024

L.R.Baggs Venue Instrukcja

23 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024