Instrukcja obsługi Linear PRO Access CAM-30DN-IP

Linear PRO Access Kamera monitorująca CAM-30DN-IP

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Linear PRO Access CAM-30DN-IP (4 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

IP Box Camera and Encoders

CAM-x- IP Series

ENC Series

po e supp y you p a to use, co su t you app a ce dea e o oca po e co pa y. o u ts te ded to ope ate o batte y po e o ot e

sources, refer to the operating instructions.

10. Grounding or Polarization This unit may be equipped with a polarized altern current line plug (a plug having one blade wider than the other). - ating-

This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing

the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized

plug. Alternatively, this unit may be equipped with a 3 wire grounding type plug, a plug having a third (grounding) pin. This plu- - g will only fit into a

grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your

obsolete outlet. Do not defeat the safety purpose of the grounding- type plug.

11. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

12. Power Lines where it - An outdoor system should not be located in the vicinity of overhead power lines or other electric light or power circuits or

can fall into such power lines or circuits. When installing an outdoor system, extreme care should be taken to keep from touching such power lines

or circuits as contact with them might be fatal. U.S.A. models only - refer to the National Electrical Code Article 820 regarding installation of CATV

systems.

13. Overloading - Do not overload outlets and extension cords as this can result in a fire or electric shock.

14. Object and Liquid Entry Never push objects of any kind into this unit through openings, as they may touch dangerous voltage points or short out -

parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit.

15. Servicing Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer -

all servicing to qualified service personnel.

16. Damage Requiring Service Unplug the unit from the outlet and refer servicing to qualified service personnel under the following conditions: -

a. When the power supply cord or plug is damaged.

b. If liquid has been spilled or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating

instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician

to restore the unit to its normal operation.

e. If the unit has been dropped or the cabinet has been damaged.

f. When the unit exhibits a distinct change in performance--this indicates a need for service.

17. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the -

manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

18. Safety Check - Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit

is in proper operating condition.

19. Coax Grounding - If an outside cable system is connected to the unit, be sure the cable system is grounded. U.S.A. models only--Section 810 of the

National Electrical Code, ANSI/NFPA No.70 1981, provides information with respect to proper grounding of the mount and supporting structure, -

grounding of the coax to a discharge unit, size of grounding conductors, location of discharge unit,connection to grounding electrodes, and

requirements for the grounding electrode.

20. Lightning or added protection of this unit during a lightning storm, or when it is left unattended and unused for long periods of time,- F unplug it

from the wall outlet and disconnect the cable system. This will prevent ne surges. damage to the unit due to lightning and power li

SAFETY PRECAUTIONS

This label may appear on the bottom of the unit due to

space limitations.

The lightning flash with an arrowhead symbol within an

equilateral triangle is intended to alert the user to the

presence of uninsulated "dangerous the product's

enclosure that may be of sufficient magnitude to

constitute a risk of voltage" within electric shock to

persons.

CAUTION: TO REDUCE THE RISK OF ELECTRICAL

SHOCK, DO NOT OPEN COVERS. NO USER

SERVICEABLE PARTS ARE INSIDE. REFER SERVICE

TO QUALIFIED SERVICE PERSONNEL.

FCC NOTICE

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the

manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits

for a Class B computing device in accordance with Part 15 of FCC Rules, which are designed to provide reasonable protection against such

interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Relocate the monitor away from the TV/radio receiver.

Plug the monitor into a different wall outlet so that the console is on a different branch circuit.

- Re orient the TV/radio antenna.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.

NOTE: Changes or modifications to the unit may void FCC compliance.

Page 3

Unpacking

Unpack carefully. This is electromechanical equipment and

should be handled with care. If an item appears to have been

damaged in shipment, replace it properly in its carton and

notify the shipper. If any items are missing, notify Linear LLC.

The shipping carton is the safest container in which the unit

may be transported. Save it for possible future use.

Service

If the unit ever needs repair service, the customer should

contact Linear LLC for a return product authorization (RPA) and

shipping instructions.

Care and Maintenance

Do not remove the cover of the unit at any time. No user-

serviceable parts are inside. Perform routine maintenance to

keep the unit dust-free. Clean the camera lens as needed. Use

a cloth approved by the lens manufacturer. If an approved

cloth is not provided, Linear recommends Kimtech Kimwipes™

Delicate Task wipes.

Model Designation

CAM- - 13DN IP 1.3MP Day/Night Camera

CAM- - 30DN IP 3.0MP Day/Night Camera

ENC- D1POE Encoder, D1 Resolution

Description

These models are box type IP cameras that are meant for -

indoor installations. These units can be installed outdoors

when installed in a suitable camera enclosure. All Linear IP

cameras can be powered over Ethernet (PoE). These models

can be powered separately, if desired, with either 12VDC or

24VAC input. All models include a dry contact relay for alarm

input (1) and output (1) as well as an RS485 connection.

• CAM- -xxxx IP models do not include a lens. This

camera accepts CS-mount Megapixel lenses. Note that

the resolution of the lens must meet or exceed the

camera resolution to provide the best possible image.

These models support Auto- Iris lenses.

• The ENC-D1POE model is an encoder which converts

an analog video signal to digital for viewing on a

network.

Hardware Kit

• CD

• This manual

• Ethernet cable, 5- ft

• Power adapter, 110VAC to 12VDC, 1.0A

• Mount bracket, silver

• 2-pin power connector

Computing Requirements

Hardware:

The minimum computing requirements for viewing the output

of the IP camera is a computer capable of running a web

browser.

Software:

Linear IP cameras are compatible with Internet Explorer (IE)

only. IE7 and IE9 are supported. Update your IE software to

the latest version available from Microsoft.

Software Settings:

Set the camera’s configuration page to be a “Trusted Site”

within Internet Explorer.

1. Navigate to the camera’s web page

2. From Menu select Tools/Internet Option

3. Click Security tab, then Trusted Sites

4. Click Sites, verify URL, then click Add

Linear IP cameras are controlled with the ActiveX lugp -in. From

the Security tab referenced above:

1. Click on Trusted Sites

2. Click on Custom Level

3. lug Enable (or set to Prompt) all ActiveX controls and p -

i ns listed below:

a. Allow previously unused ActiveX controls to

run without prompt

b. Allow Scriplets

c. Automatic prompting for ActiveX controls

d. Binary and script behaviors

e. Display video and animation on a webpage

that does not use external media player.

f. Download signed ActiveX controls

g. Download unsigned ActiveX controls

h. Initialize and script ActiveX controls not

marked as safe for scripting

i. ins Run ActiveX controls and plug-

j. Script ActiveX controls marked safe for

scripting

Specyfikacje produktu

Marka:	Linear PRO Access
Kategoria:	Kamera monitorująca
Model:	CAM-30DN-IP

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Linear PRO Access CAM-30DN-IP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kamera monitorująca Linear PRO Access

Linear PRO Access LV-D4-2MDI-312 Instrukcja

16 Września 2024

Linear PRO Access LV-B3MDIW-312 Instrukcja

13 Września 2024

Linear PRO Access LV-CAM-2M Instrukcja

12 Września 2024

Linear PRO Access CAM-30DN-IP Instrukcja

5 Września 2024

Linear PRO Access LV-D2-2MIV-3.6F Instrukcja

5 Września 2024

Linear PRO Access LV-D4-5MDIV-312 Instrukcja

5 Września 2024

Linear PRO Access LV-CAM-5M Instrukcja

4 Września 2024

Linear PRO Access LV-D4-2MDIV-312 Instrukcja

4 Września 2024

Linear PRO Access LV-B2MDI-312 Instrukcja

2 Września 2024

Linear PRO Access LV-CAM-3MW Instrukcja

1 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025