Instrukcja obsługi Lindell Audio LiNTEC

Lindell Audio Niesklasyfikowane LiNTEC

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lindell Audio LiNTEC (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

protection. No part of this document may be reproduced in any form without explicit written

consent from Lindell Audio. Lindell Audio is a RAD Global Distribution company.

LiNTEC

Vintage Program Equalizer

Specications

EQ Switch

Settings

5-Step Switched EQ Low Freq Boost/Atten:

20, 30, 60, 100, 150 Hz +/-10%

11-Step Switched EQ High Freq Boost:

1, 1.5, 2, 3, 4, 5, 6, 10, 12, 14, and 16 kHz +/-10%

5-Step Switched Eq High Freq Atten:

4, 8, 12, 16, and 20 kHz +/-10%

Voltage 115 VAC, 230 VAC rear panel switchable AC Mains Input: IEC320-C14 standard plug.

Dimensions Width: 438 mm (19”)

Height: 88 mm (2U)

Depth: 250 mm

1. Read these instructions.

2. Keep these instructions

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such

as radiators, heat registers, stoves, or

other apparatus that produce heat.

9. Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus. If the

power cord becomes frayed, stop using

immediately.

10. Use only attachments/accessories

specied by the manufacturer

11. Use only with a cart, stand, tripod, bracket

or table specied by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury

from tip-over.

12. Unplug this apparatus during lightning

storms or when unused for long periods

of time.

13. Refer all servicing to qualied service

personnel. Servicing is required when

the apparatus has been damaged in any

way, such as power supply cord or plug

is damaged, liquid has been spilled or

objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture, does not operate normally, or

has been dropped.

14. This apparatus shall not be exposed to

dripping or splashing, and no object lled

with liquids, such as vases, shall be placed

on the apparatus.

15. Note that this apparatus is not completely

disconnected from the AC mains service

when the power switch is in the OFF

position.

16. The mains plug or power inlet on the

product is used as the disconnect device,

so the disconnected device shall remain

readily operable when reconnected.

17. Any changes or modications not

expressly approved in this manual

could void your authority to operate this

apparatus.

Important!

Be sure to only use the supplied 12V AC

supply with this unit. Other supplies can

potentially damage the unit.

The lightning ash with an arrowhead sym-

bol within an equilateral triangle is intended

to alert the user to the presence of uninsu-

lated “dangerous voltage” within the prod-

uct’s enclosure that may be of sufcient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilater-

al triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

The Lindell Audio LiNTEC complies with

all applicable / RoHS / WEEE European

Union directives.

Do not attempt to service this unit yourself,

1. Power switch: Turns the unit off.

2. Bypass switch: Bypasses the EQ

circuit, useful for A/B compar-

isons.

3. VU Meter: Displays output VU

level.

4. (LF) Boost: Selects the amount of

boost at the frequency selected

by the Low Freq control.

5. Low Freq: Selects the frequency

affected by the LF Boost and LF

Atten controls.

6. (LF) Atten: Selects the amount

of attenuation at the frequency

selected by the Low Freq control.

7. Bandwidth: Selects the width

(Q) of the HF Boost control.

Left=narrow, right=wide.

8. (HF) Boost: Selects the amount of

boost at the frequency selected

by the High Freq control.

9. High Freq: Selects the frequen-

cy affected by the HF Boost

control.

10. (HF) Atten: Selects the amount

of boost at the frequency select-

ed by the High Freq control.

11. HF Atten Freq: Selects the fre-

quency affected by the HF Atten

control.

12. TRS Output: Balanced line-level

output.

13. TRS Input: Balanced line-level

input.

14. Meter Calibration: Use this

control to adjust the 0 VU point

at +4 dB.

15. Output Level: Use this control

to adjust the output level of the

LiNTEC to match that of another

LinTEC for stereo use.

16. Voltage setting: Select the volt-

age suitable to your region. Do

not power the LiNTEC by inap-

propriate voltage.

17. AC Adapter Input: ONLY use

the supplied 12VAC to power

this unit.

Note: For proper

performance, balanced

TRS must be used for all

inputs and outputs.

Important Safety Instructions

as it will void your warranty. Please check

your unit carefully upon receipt and return

to place of purchase immediately if there

are any problems with the product. After

that, the standard Lindell Audio 1 YEAR

warranty will apply to defects in materials

and workmanship.

International Service

For service or warranty assistance, please

contact the Lindell Audio distributor in your

country through the dealer from whom you

purchased this product.

Limited 1 Year Warranty

Lindell Audio’s LiNTEC is warranted by Lin-

dell Audio to be free from defects in ma-

terials and workmanship for the period of

ONE (1) YEAR to the original purchaser. In

the event of such defects, the product will

be repaired without charge or, at our op-

tion, replaced with a new one if delivered to

Lindell Audio prepaid, together with a copy

of the sales slip tor other proof of purchase

date. The warranty excludes problems due

to normal wear, abuse, shipping damage

or failure to use the product in accordance

with the specications.

All parts and labor are covered under this

Limited Warranty. However, if it is deter-

mined by Lindell Audio that the device was

damaged or made defective through abuse,

we reserve the right to charge the customer

for the cost of the repair.

Lindell Audio shall not be liable for damag-

es based upon inconvenience, loss of use

of the product, loss of time, interrupted

operation or commercial loss or any other

damages, whether incidental, consequen-

tial or otherwise. This warranty gives you

specic legal rights, and you may have oth-

er rights, which will vary from state to state.

This warranty is not transferable.

Quick Start Guide

1. Mute your studio monitors.

2. Connect your LiNTEC to your mix-

ing bus or patch bay then using bal-

anced TRS cables.

3. Set all controls to noon (straight up.)

4. Set the switch to ON, Bypass Power

to OFF, and apply power. Power

LED meter will light up.

5. Unmute your monitors, and verify

that signal is passing to and from

the unit.

6. Send your desired signal through

the LiNTEC.

7. Adjust the controls and listen for

changes in the program material.

8. If you hear the controls affecting

the character of your music, the

unit is functioning correctly.

Basic Use

The LiNTEC works a little differently than other

parametric or graphic EQs you may have used in

the past.

The three control knobs on the left of the LiN-

TEC (Boost, Low Freq, and Atten) affect low-fre-

quency content. The Boost and Atten controls

both affect the frequency chosen by the Low Freq

control.

The ve control knobs on the right of the LiN-

TEC (Bandwidth, Boost, High Freq, Atten, and

Atten Freq) affect high-frequency content. The

Boost and Atten controls each have their own

corresponding frequency selectors, (High Freq

for the Boost control, Atten Freq affects the Atten

control.)

The Low-End Trick

Documentation for the original Pultec rather

bullishly asserted “Do not attempt to boost

and attenuate simultaneously on the low

frequencies.” So, of course, that’s exactly what

curious, rascally engineers did. The result of this

simultaneous boost/cut operation is a low-end

boost below the selected frequency, with a cut

slightly above the selected frequency.

Because the bandwidth (Q) of the Boost and At-

ten controls differ, the two controls do not cancel

each other out. This setting results in satisfying

thump and body that doesn’t risk muddying the

midrange, and has been a not-so-secret trick of

engineers and producers ever since.

Try it, you’ll like it.

Meter Calibration

Meter should be calibrated so that 0 VU = +4 dB.

This is controlled the the master calibration set

screw on the back of the unit.

Allow 1-2 minutes to let the LiNTEC warm up

after powering on before calibrating the meter’s

zero-point — heat from the bulb can gently affect

the meter.

To calibrate, ensure that no audio is passing

through the unit. Then, using a athead screw-

driver, rotate the screw on the rear panel until the

needle rests on 0. Use very small movements... a

little goes a long way in meter calibration!

Voila! Meter calibrated.

Output Calibration

All LiNTECs are hand-calibrated at the factory

to match each other at unity gain within 0.2 dB

for use in matched stereo pairs. This calibration

is measured with all controls set fully count-

er-clockwise.

We doubt it will be necessary, but if you would

like to re-calibrate your unit, adjust the Output

Calibration control on the back of the unit.

The 1731 op-amp

The LiNTEC’s “VINTAGE OPA 1731” is our take on

the classic vintage 1731 op-amp – the predecessor

to the 2520, known for its smooth, punchy char-

acter.

We think you’ll like it as much as we do.

2 3 4 9 10

12 14

13 15 16

6 85

Specyfikacje produktu

Marka:	Lindell Audio
Kategoria:	Niesklasyfikowane
Model:	LiNTEC

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Lindell Audio LiNTEC, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Lindell Audio

Lindell Audio LiNTEC Instrukcja

4 Października 2024

Lindell Audio PeQ-501a Instrukcja

28 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024