Instrukcja obsługi Lightware HDMI-TPS-TX95

Lightware przedłużacz AV HDMI-TPS-TX95

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lightware HDMI-TPS-TX95 (2 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Quick Start Guide

HDMI-TPS-TX95

HDMI-TPS-RX95

DVI-HDCP-TPS-TX95

DVI-HDCP-TPS-RX95

Further Information

The Product brief of this appliance and further information is available at www.lightware.com.

See the section on the dedicated product page.Downloads

sales@lightware.com

+36 1 255 3800

support@lightware.com

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 2.1

19200118

Locking DC Plug

Twist 90° clockwise to lock.

Connecting Steps

RS-232 port Local RS-232 port for bidirectional serial data connection and

performing rmware upgrade (programming).

RS-232 switch Normal: serial data is passed through the device.

Prog: RS-232 pass-through function is disabled, the device is

ready for the rmware upgrade.

Status LEDs See the next section.

TPS mode

switch

LR: Long reach TPS mode; lower resolution (max 1080p),

longer distances; : TPS mode is determined automatically.Auto

IR input IR signal input connector (for 3.5 mm Jack, 3-pole, TRS plug).

IR output IR signal output connector (for 3.5 mm Jack, 2-pole, TS plug).

DC input 12V DC input for local power supply.

Ethernet port The Ethernet data is passed through the device.

TPS port TPS port to the other compatible device (extender / matrix /

board).

HDMI port Video port for DVI or HDMI signal.

Front and Rear View – Legend

Important Safety Instructions

Please read the supplied safety instruction document before using the product and keep it

available for future reference.

Introduction

The HDMI-TPS-RX/TX95 and DVI-HDCP-TPS-RX/TX95 are DVI 1.0 and HDMI 1.4

compatible long-distance extenders. The difference between HDMI and DVI-HDCP models

is just the HDMI and DVI connector. The units offer bi-directional RS-232, Infra-Red (IR), and

Ethernet signal pass-through on the same CAT5e...CAT7 cable that carries the uncompressed

HDMI video and audio signal.

Box Contents

Remote Power Options

The TPS extenders can be powered remotely by its extender pair or a TPS matrix board. This

feature can be enabled or disabled with jumper settings. Switch off the extenders. Loose the

screws and remove the small plate from the right side of the enclosure. To enable the remote

power function place the jumper block onto all the pinheads. To disable it place the jumper

block onto the upper line pinheads only. In case of enabled remote power on both extenders

the local adaptor can be placed at any side.



The TPS remote powering must be used only with 95 series TPS extenders and MX

TPS matrix boards. Using it with other devices may damage both units. Connecting

incompatible devices with similar connectors may cause harm to the devices. Never

connect any third party device to the extender with remote powering!



AWG 26 cables are not recommended with remote powering (reduce cable distances).

Extender unit 12V DC adaptor with

interchangeable plugs

Infrared detector unit

(for RX95)

Infrared emitter unit

(for TX95)

Safety and Warranty info,

Quick Start Guide

Front View

Rear View



The transmitters and the receivers have the same construction and connectors.

The product is compatible with

HDBaseT

and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

Status LEDs

HDCP

OFF: video output signal is not encrypted with HDCP.

ON: video output signal is encrypted with HDCP.

VIDEO

OFF: no video signal transmission.

ON: video signal transmission.

LINK

OFF: TPS connection failed between the devices.

BLINKING: TPS connection is detected and LPPF link mode is active.

ON: TPS connection is detected and HDBT or LR link mode is active.

LIVE

OFF: no power supply or out of order.

BLINKING: device is powered and ready to use.

TPS link modes

If an extender and a TPS matrix board are paired the board forces the extender to use the

settings of the matrix. The extender’s TPS mode switch has no effect. For detailed information

about the TPS link modes in case of matrix boards see the user’s manual of the matrix.

Installation of the Extender with a Matrix

1. Power off all devices. (Installing with powered devices may harm them.)

2. Check the RS-232 switch(es) on the extender(s); they must be in Normal position.

3. The state of the TPS link mode switch makes no difference on the extender because the

connected board forces the extender to use the settings of the matrix.

4. Set the remote power mode of the matrix boards with the jumpers on them. Every port

can be set for remote powering separately. To enable the remote power function place

the jumper block onto all the pinheads of the desired port. To disable it remove the jumper

block. For detailed information, see the user’s manual of the matrix.

5. Set the extenders’ remote power mode with the same method as it mentioned in the

standalone case.

6. Pair the extender(s) and the matrix board(s) with CATx cable(s). The transmitters’ TPS

OUT with the input boards’ TPS IN and the receivers’ TPS IN with the output boards’

TPS OUT.

7. Connect the video source(s), sink(s) and the desired accessory device(s) to the matrix

(MX-TPS boards don’t support the IR pass-through).

8. Connect the video source(s), sink(s) and the desired accessory device(s) to the extend-

ers.

9. Supply that matrix boards with 12V 6,67A DC which have ports with enabled remote

powering.

10. Supply the extenders with 12V 2A DC. If the remote power is disabled on the connected

matrix card’s port, local adaptor must be used for the extender.

11. Connect the power cord of the matrix into the outlet and switch on the matrix.

12. Supply the other connected units.

Safety and

Warranty

Info

Quick

Start

Guide

1 2 4 53 6

987 q

Mounting Options

Lightware offers three types of mounting accessory to x the extenders:

Under Desk Mounting Kit (UD-kit)

The UD-kit makes easy to mount one extender under any at surface (e.g. furniture).

UD Mounting Kit Double (UD-kit double)

The UD-kit double makes easy to mount two extenders under any at surface (e.g. furniture).

Rack Shelf

1U high rack shelf provides mounting holes for fastening up to extenders.four

Mounting Steps



Always use the xing screws which are supplied with the mounting accessory. If

you insert screws longer than 6 mm, the device can be damaged.

1. Unplug all the cables connected to the device(s).

2. Turn the device(s) upside down.

3. Put the shelf upside down on the device(s). Position it to get the mounting holes aligned.

4. Fasten the device on the shelf with the provided screws.

5. Fix the shelf to the desired place (screws are not supplied).

CATx

Connect the TPS output port of the Transmitter to the TPS input port of the

Receiver by a CATx cable.

HDMI

Connect a source to the HDMI (DVI-D) input port of the transmitter.

Connect an IR emitter unit to the IR output port of the transmitter.

RS-232

Connect a controller device to the local RS-232 port of the transmitter.

Make sure the RS-232 switch is in position.Normal

LAN

Optionally connect a laptop to the Ethernet port of the transmitter.

HDMI

Connect a sink device to the HDMI (DVI-D) output port of the receiver.

RS-232

Connect a serial cable between the sink device and the RS-232 port of the

receiver.

LAN

Connect the receiver to Ethernet by a CATx cable.

Connect an IR detector unit to the IR input port of the receiver.

Power

Firstly connect the power adaptor to the DC input of the power injector, then

secondly to the AC power socket.

TX side RX side

Enabled

Disabled

(default)

RS-232

HDMI Power

Power HDMI

Touch panel

Blu-ray player IR emitter

Ethernet switch IR detector

Power adaptor

Power

adaptor

Laptop

Projector

HDMI-

TPS-TX95

HDMI-

TPS-RX95

CATx

RS-232 LAN IR

LAN

RS-232 Normal Prog IR IN IR OUT

HDMI-TPS-TX95

Transmitter

LR Auto

SIGNAL

LIVE

LINK

HDCP

RS-232 Normal Prog IR IN IR OUT

HDMI-TPS-RX95

Receiver

LR Auto

SIGNAL

LIVE

LINK

HDCP

Remote Power Options

The TPS extender can be powered remotely by the connected TPS matrix board or its

extender pair. This feature can be enabled or disabled with jumper settings for every port

separately. Switch off the matrix. Remove the desired cards. Pinheads are behind of the TPS

connectors. To enable the remote powering function of the port place the jumper block onto all

the corresponding pinheads. Connect the external 12V DC 6,67A power adaptor to the card

separately. Finally, set the extenders’ desired power modes. To disable the remote powering

function for a port remove the jumper block from the corresponding pinheads.

Jumper Settings

Place the jumper blocks onto all the pinheads

of those units which you want to be powered

remotely. For disabling the remote powering

remove the jumper blocks and place them

onto the upper line pinheads only.

 Read carefully all the detailed

instructions about remote powering

devices! Never use remote powering with

third-party units!



AWG 26 cables are not recommended for

remote powering (reduce cable distances).



For more information please download

the User’s Manual of the MX-FR matrix

switchers.

Infra-Red (IR)

One emitter and one detector is enough for remote controlling one IR sink device. If there is an

IR sink device to be controlled next to the TX and the other one is next to the RX, two emitter-

detector pairs are needed. The IR emitter and the detector have standard 3.5 mm TRS (jack)

connectors. The emitter’s plug has two poles (mono) and the detector’s plug has three poles

(stereo).



The second emitter and detector pair can be ordered from Lightware separately.



IR extension is available only with point-to-point connection of the extenders.

1 2 3

1 2-3

Detector – 3-pole-TRS Emitter – 2-pole-TS

1 Tip 1 TipSignal (active low) +5V

2 Ring 2 RingGND Signal (active low)

3 Sleeve 3 Sleeve+5V

Integrated with Local Powering

Standalone with Remote Powering for TX

Standalone with Remote Powering for RX

Standalone with Local Powering

Integrated with Remote Powering for

RX and TX

Typical Application

Maximum Extension Distances

Resolution Pixel

clock rate

Cable lengths

(Auto / Long reach TPS mode)

CAT5e

AWG24

CAT7

AWG26 **

CAT7

AWG23

1024x768@60Hz 65 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*

1280x720p@60Hz 73.8 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*

1920x1080p@60Hz (24bpp) 148.5 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*

1920x1200@60Hz 152.9 MHz 100 m / NA 90 m / NA 120 m / NA

1600x1200@60Hz 162 MHz 100 m / NA 90 m / NA 120 m / NA

1920x1080@60Hz (36bpp) 223 MHz 70 m / NA 70 m / NA 100 m / NA

3840x2160@30Hz UHD 297 MHz 70 m / NA 70 m / NA 100 m / NA

4096x2160@30Hz 4K 297 MHz 70 m / NA 70 m / NA 100 m / NA

* Long reach TPS mode supports pixel clock frequencies up to 148.5 MHz.

** AWG 26 cables are not recommended with remote powering.

Above values are valid when the transmitter is powered by a local adaptor; distances may

decrease depending on the powering mode (local or remote) and cable quality. To specify

the accurate extension distances, please also check the documentation of the connected

HDBaseT-compatible device.



CAT7 SFTP AWG23 cable is always recommended.

Bi-directional Pass-through Data Lines

The direction of the video extension is xed from TX towards RX but the pass-through data

lines are bi-directional. It means the RS-232, IR, Ethernet source and sink devices can be

connected either to the TX or the RX.

Ethernet

The Ethernet port on the RX or on TX can be connected to a LAN hub, switch or router with a

LAN cable. The other side behaves as an Ethernet uplink port. Extenders support 10/100 Mbit/

sec data transfer rate. The direct access is also supported with cross-link cable. The Ethernet

port has auto crossover function. It is able to recognize and handle both cable types: patch

and cross TP cables.

RS-232

Third party devices with standard RS-232 port are supported as the extenders work in pass-

through mode. TX and RX provide 9-pole D-sub female connector. Use straight-serial cable

to connect a DTE device to an extender and use a cross serial cable in case of pairing a DCE

device to the other TPS extender. The RS-232 options – the baud rate and the parity bits are

set on the third party devices and it can be anything. The extenders support any kind of serial

settings.



Please read the user’s manual of the RS-232 device to get its type. The extenders work

as DCE devices.

TPS Link Modes

The TPS working mode between the transmitter and the receiver parties is determined by

the mode set in them. Both parties inuence on the setting which determines the nal TPS

transmission mode. The following TPS modes are dened:

Long reach (LR): Longer CATx cable length, less bandwidth (limited resolution). The

LPPF mode is not available in LR TPS link mode.

HDBaseT

(HDBT): more bandwidth (higher resolutions), shorter CATx cable length. If

no video present, the units change to LPPF mode automatically.

Low Power Partial Functionality (LPPF): Only Ethernet, RS-232 and IR are extended.

Toggling Between TPS Link Modes

The toggle switch on the extenders can be used to toggle between

the LR and Auto TPS modes. If both units have Auto state and

there is valid video signal on the transmitter the common mode

will be HDBT. If the video signal disappears devices go into LPPF

mode.

TPS mode between an extender and a port of a matrix board

If an extender and a TPS matrix board

are paired the board forces the extender

to use the settings of the matrix. The

extender’s TPS mode switch has no effect.



Always use the Auto mode with

third-party devices!

The negotiated

TPS working mode

Selected mode (RX)

LR Auto

Selected

mode

(TX)

LR LR LR

Auto LR HDBT

Specication

General

Compliance CE ...............................................................................................................

EMI / EMC EN 55035:2017 / EN 55032:2015 ...............................................................

Cooling .............................................................................................................. passive

Enclosure ......................................................................................................1 mm steel

Dimensions ................................................................... 100.4 W x 100x4 D x 26 H mm

Weight (TX) .............................................................300 g (HDMI) / 310 g (DVI-HDCP)

Weight (RX) ............................................................320 g (HDMI) / 330 g (DVI-HDCP)

Digital Video Signal

Supported signals ........................................................................... DVI 1.0, HDMI 1.4

Signal standard DVI and HDMI standard which supports embedded audio ................

Supported resolutions .........................................................1920x1080@120 Hz, 24 bit

................................................. up to 4K / UHD (30Hz RGB 4:4:4, 60Hz YCbCr 4:2:0)

3D support yes ...............................................................................................................

HDCP compliant yes ......................................................................................................

CEC support * ...............................................................................................transparent

EDID support transparent ..............................................................................................

*Only between HDMI-TPS-TX95 and HDMI-TPS-RX95 models.

Cable length (HDMI/DVI input port) ............................................................. max. 20 m

Equalization .................................................................................... adaptive, automatic

Power

Power supply ................................... external power adaptor / remote power via TPS

Power adaptor ......................... Input 100-240 V AC 50/60 Hz, Output 12V DC, 2.5 A

Power consumption (TX) ....................................................... 3.6W (typ) / 4.2W (max)

Power consumption (RX) ...................................................... 5.3W (typ) / 6.1W (max)

Connectors

TX input, RX output .................................................................. HDMI / DVI-I connector

TX output, RX input ......................................................................RJ45 (TPS interface)

Ethernet ................................................................................................................. RJ45

IR input, output ................................................................ 3.5 mm (1.8”) jack connector

Serial port 9-pole D-sub ...................................................................................................

Power ................................................................... locking DC connector (2.1 / 5.5 mm)

TPS port (HDBaseT

-compatible)

Ethernet pass-through yes .............................................................................................

RS-232 pass-through ............................................................................................... yes

IR pass-through ........................................................................................................ yes

When remote power is enable d, 12V present on TPS connector

Check compability before connecting devices .

For best performance use CAT6 or CAT7 SFTP ca ble

HDMI

IR cable

Serial cable

Touch panel

IR emitter

IR detector

Blu-ray player

HD Projector

Projection

screen

Ethernet switch Internet

LAN

TPS connection

CATx up to 170 m

LAN

HDMI-

TPS-TX95

HDMI-

TPS-RX95

HDMI-HDMI

cable

12V DC

Power adaptor

SIGNAL

LIVE

LINK

HDCP

Disabled

(local)

DVI-HDCP-

TPS-TX95

DVI-HDCP-

TPS-RX95

12V DC

Power adaptor

12V DC

Power

adaptor

No power send

CATx

Disabled

(local)

Enabled Enabled

DVI-HDCP-

TPS-TX95

DVI-HDCP-

TPS-RX95

12V DC

Power

adaptor Power send CATx

Enabled Enabled

DVI-HDCP-

TPS-TX95

DVI-HDCP-

TPS-RX95

12V DC

Power

adaptor

Power send CATx

DVI-HDCP-

TPS-TX95

DVI-HDCP-

TPS-TX95

DVI-HDCP-

TPS-TX95

DVI-HDCP-

TPS-RX95

12V DC

Power

adaptor

12V DC

Power

adaptor

No power

send

Power send

CATx

Disabled

(local)

MX-TPS-IB- S

12V 3A

DC IN

8 CH TPS INPUT BOARD 12V power on TPS connector. Only use with compatible devices!

TPS IN 1 TPS IN 2 TPS IN 3 TPS IN 4 TPS IN 5 TPS IN 6 TPS IN 7 TPS IN 8

MX-TPS-IB- S

12V 3A

DC IN

8 CH TPS INPUT BOARD 12V power on TPS connector. Only use with compatible devices!

TPS IN 1 TPS IN 2 TPS IN 3 TPS IN 4 TPS IN 5 TPS IN 6 TPS IN 7 TPS IN 8

MX-TPS-OB

12V 4A

DC IN

8 CH TPS OUTPUT BOAR D 12V power on TPS connector. Only use with compatible devices!

TPS OUT 1 TPS OUT 2 TPS OUT 3 TPS OUT 4 TPS OUT 5 TPS OUT 6 TPS OUT 7 TPS OUT 8

MX-TPS-OB

12V 4A

DC IN

8 CH TPS OUTPUT BOAR D 12V power on TPS connector. Only use with compatible devices!

TPS OUT 1 TPS OUT 2 TPS OUT 3 TPS OUT 4 TPS OUT 5 TPS OUT 6 TPS OUT 7 TPS OUT 8

Enabled

Disabled

(local)

Power

send

CATx

Specyfikacje produktu

Marka:	Lightware
Kategoria:	przedłużacz AV
Model:	HDMI-TPS-TX95
Kolor produktu:	Czarny
Technologia łączności:	Przewodowa
Bluetooth:	Nie
Gniazdko wyjścia DC:	Tak
Zasilacz sieciowy:	Tak
Napięcie pracy:	12 V
Wi-Fi:	Nie
Przewodowa sieć LAN:	Tak
Kompatybilność 3D:	Tak
Diody LED:	Tak
Model:	Nadajnik AV
Adapter zewnętrznego zasilania:	Tak
Prąd wejściowy:	2.5 A
Maks. rozdzielczość:	4096 x 2160 px
Wersja HDMI:	1.4
HDCP:	Tak
Szerokość pasma:	3.4 Gbit/s
Materiały:	Metal
Maksymalny dystans transferu:	170 m
Obsługiwane rozdzielczości grafiki:	1024 x 768 (XGA),1280 x 720 (HD 720),1600 x 1200 (UXGA),1920 x 1080 (HD 1080),1920 x 1200 (WUXGA),3840 x 2160,4096 x 2160
HDMI in:	1
Zdalne wejście IR:	1
Obsługiwane tryby wideo:	1080p
Zdanlne wyjścia IR:	1
Szeregowe porty komunikacyjne:	1
Interfejs SCSI:	RS-232
Wymiary transmitera (SxGxW):	100.4 x 100.4 x 26 mm
Waga transmitera:	330 g
Obsługiwane typy kabli:	Cat5, Cat6, Cat7
Wyjścia RJ-45:	2
Rozszerzone dane identyfikacyjne wyświetlacza (EDID):	Tak
Zużycie prądu (nadajnik) (max):	4.2 W
Przejście HDCP:	Tak
Przedłużać podczerwieni:	Tak
Przejście RS-232:	Tak
Brak kompresji wideo:	Tak
Pobór mocy (TX):	3.6 W