Instrukcja obsługi Lightware HDMI-TPS-RX120-HDSR

Lightware przedłużacz AV HDMI-TPS-RX120-HDSR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lightware HDMI-TPS-RX120-HDSR (2 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Quick Start Guide

HDMI-TPS-RX120-HDSR

Further information

The document is valid with the following rmware version: 3.16

The Product Brief and further information is available on www.lightware.com.

See the Downloads section at the website of the product.

sales@lightware.com

+36 1 255 3800

support@lightware.com

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 1.2

19200116

Important Safety Instructions

Please read the supplied safety instruction document before using the product and keep it

available for future reference.

Introduction

HDMI-TPS-RX120-HDSR is a TPS receiver with a local HDMI input and a built-in HD video

scaler. Conversion between common formats and frame rates are supported. One common

resolution can be used across a system independently of the connected displays requirement,

which improves general performance.

The connected display receives continuous HDMI signal thanks to the scaler, thus eliminating

annoying warnings and longer interruptions when switching the input signal.

Compatible Devices

The receiver is compatible with other Lightware TPS devices, TPS and TPS2 output boards,

as well as third-party HDBaseT-extenders, displays, but not compatible with the phased out

TPS-90 extenders.

The product is compatible with any HDBaseT

third party devices.

HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

Box Contents

Optional Accessory

The following accessory can be purchased separately:

Powering Options



The receiver cannot be powered remotely, always use the supplied power adaptor.

Warranty is void if damage occurs due to use of a different power source.

Locking DC Connector

The DC connector has a small latch which helps to avoid

an unwanted power disconnection – push the plug until it

stops. Be careful when disconnecting the DC plug from the

connector, do not pull it by grabbing the cable, always grab

the movable plastic angular housing as indicated in the gure.

Receiver unit External Power Supply

Unit (24V / 2.7A)

Remote Control unit

with AAA battery (2x)

IEC power cable

Safety and Warranty info,

Quick Start Guide

USB Port The port is used to perform a rmware upgrade only.

IR Sensor Receiving the IR signals from the supplied remote controller.

HDMI Output Connect an HDMI cable between the receiver and the

display device.

HDMI Input Connect an HDMI cable between the HDMI source and

the receiver unit.

Input LED Green: TPS input is switched to the output.

Red: HDMI input is switched to the output.

Front Panel

Buttons

The buttons can be used for OSD menu navigation and fast

output format change (see the details below).

Input selector

Exit from the current menu/parameter

OK button to save the actual setting

Reserved

Displaying the OSD menu

Menu navigation buttons

Reserved

Power LED If the LED lights, the device is powered and ready to use.

DC 24V Input 24V DC input for local power supply.

RS-232 Port Local RS-232 port for bidirectional serial data

communication; see the RS-232 Communication section.

Ethernet The Ethernet data is passed through the device between

the Ethernet and the TPS port.

IR Ports IR input/output connectors (3.5 mm Jack).

TPS Input TPS input port for connecting a compatible device.



Batteries shall not be exposed to excessive heat

such as sunshine, re or the like.

Front Panel Buttons

MENU Button

Displaying/hiding the OSD menu (HDMI output).

Button

Moving left in the main menu, moving up in a submenu, or decreasing the value of a

parameter.

Toggle the input ports: when the OSD is not displayed, the other input can be selected.

Button

Moving right in the main menu, moving down in a submenu, or increasing the value of a

parameter.

Enter Button

Selecting a menu/submenu item, or saving the value of a parameter.

Button Combinations

 and Enter: changing the output resolution to 1920x1080p60 (Full HD) immediately.

 and Enter: changing the output resolution to 1024x768p60 (XGA) immediately.

Front View

Mounting Options

The receiver can be mounted by the optional VESA100 Mounting adapter (please contact

sales@lightware.com). See the below example about the application:

Two mounting holes can be found at the bottom of the receiver at each side, the Mounting

adapter can be xed as indicated. The other two holes of the plate can be xed to a VESA-

mounting compatible device (e.g. rear panel of an HDTV).



The VESA100 Mounting adapter can be used to x the receiver e.g. under the desk.

Connecting Steps Remote Control Unit (Optional Accessory)

Bi-directional Pass-through Data Lines

The direction of the video extension is xed from the transmitter side towards to the receiver

but the pass-through data lines are bi-directional. Thus, RS-232, IR, Ethernet source and sink

devices can be connected either to the TX or to the RX and the signal is transmitted to the

other extender.

2Tx data

3Rx data

5Ground

Installing the AAA Batteries

Pay attention to the polarity of the batteries as

shown in the gure.

IR Input IR Output

1IR signal Power

2Power IR signal

3Ground Ground

Rear View

About the IR Extension

The IR input and output ports receives/sends baseband IR signal, no modulation/demodulation

is done. These ports are suitable for wired IR connections mostly.

IR Port Pinout (Applicable Plugs)



The IR Transmitter and Receiver units supplied with other Lightware devices cannot

be connected to the receiver directly.

RS-232 Communication

The serial data coming from the TPS line is passed through to the RS-232 port and vice versa.

If the incoming command is known by the receiver, it will be processed. Please note that in

such cases the response from the receiver will be sent to the sender only. E.g. if a command is

sent from the local RS-232 port, the response would not be sent over the TPS line but appear

only at the local RS-232 port.

RS-232 Port Pinout

CATx

Connect a CATx cable between the receiver and a compatible

transmitter or output board.

HDMI

Connect a monitor to the HDMI output port.

HDMI

Optionally connect a HDMI source (e.g. laptop) to the HDMI input port.

LAN

Optionally connect the receiver to an Ethernet switch by a CATx cable.

Power

Connect the attached PSU to the receiver and then to the power socket.

HDMI-TPS-

RX120-HDSR

Monitor

Laptop Ethernet

Power Supply Unit

Compatible

transmitter or

output board

HDMI

HDMI Power

LAN

CATx

HDMI OUT HDMI INSERVICE MENU ENTER

Set to XGA

Set to 1080p

2 3

Receiver

(bottom view)

VESA100

Mounting adapter

100 mm

67.5 mm

HDTV

(rear view)

MENU ENTER

Set to XGA

Set to 1080p

INPUT

EXIT MENU

RESET AUTO

ADJUST

1 2 3 4 65

Safety and

Warranty

Info

Quick

Start

Guide

1 2 63 4 5

Explanation



The response values are single Bytes except in the case of the [OUTPUT] which is always

a double Byte, eg. ‘12’.

List of RS-232 Commands



The underlined values mean the default settings.

Typical Application

RS-232 Commands

Below listed commands can be used to query or control the receiver. The commands can be

sent via the local RS-232 port or via the TPS line. Please check the serial port settings which

are xed in the device:

Baud rate data bit: 9600; : 8 bits; : none; parity stop bit: 1



Connect a cross-link serial cable between the receiver and a computer.

Protocol Description

The commands must be followed by Carriage return and Line feed (<CR><LF>).

The parameters can be by the letter in each case.queried (read) ’R’

The parameters can be by the set ’S’ letter.

The commands are not case-sensitive.

The ● symbol means the space character in below examples.

Supported Resolutions (HDMI Input Port)

* with reduced blanking

Querying a Parameter

Format Example

Command

Response

R●OUTPUT<CR><LF>

OUTPUT=<current_setting><CR><LF>

→

←

r output

OUTPUT=12

Setting a Parameter

Format Example

Command

Response

S●OUTPUT●<new_setting><CR><LF>

OUTPUT=<new_setting><CR><LF>

→

←

s output 8

OUTPUT=8

Setting the Output Resolution (RGB, YUV)

OUTPUT <set>

0 = native

1 = 640x480@60

2 = 800x600@60

3 = 1024x768@60

5 = 1360x768@60

6 = 1280x720@60

7 = 1280x800@60

8 = 1280x1024@60

9 = 1440x900@60

10 = 1400x1050@60

11 = 1680x1050@60

12 = 1600x1200@60

13 = 1920x1080@60

16 = 1920x1200@60

17 = 720x480p60

18 = 1280x720p60

19 = 1920x1080p60

20 = 1920x1080p60

22 = 720x576p50

23 = 1280x720p50

24 = 1920x1080p50

25 = 1920x1080i50

Setting the Visibility of the Input Port Status Info (OSD, Top Left Corner)

INFO DISPLAY <set> 0 1 2 = off = 5 sec = always on

Selecting the Input

SOURCE <set> 1 = HDMI 2 = TPS

Hsync Shifting (for Compatibility Reasons)

HSYNC SHIFT <set> 0 1 = off = on

Locking the Front Panel Buttons

KEY LOCK <set> 0 1 = unlocked = locked



When the keys are locked the RS-232 commands can be used only for querying the

parameters. Modication is not possible, only the ‘S KEY LOCK 1’ setting command is

accepted.

Querying the Type of the Current EDID

EDID TYPE <set> 1 = stereo LPCM = multichannel2

Querying the Type of the Device (for LW2 Protocol Compatibility)

{i} response: (I:HDMI-TPS-RX120-HDSR)

Setting the Audio Delay

AUDIO DELAY <set> 0 = off

1 = 40 ms

2 = 110 ms

3 = 150 ms

Muting the Audio

AUDIO MUTE <set> 0 1 = unmuted = muted

Querying the Current Firmware Version

FW note: R/S prex is not necessary

Reloading the Factory Default Values

S RESET 1

Selected input TPS input port

Output size Best fit

Audio unmuted, 40 ms delay

Front panel buttons (key lock) unlocked

Input port status info display (OSD) off

Emulated EDID type at the input port audio supported (stereo LPCM)

RS-232 port setting (device control) 9600 BAUD, 8, N, 1

Factory Default Settings

Specications

General

Compliance ................................................................................................................CE

EMI / EMC .................................................................................. EN 55024 / EN 55032

Cooling .............................................................................................................. passive

Enclosure ...................................................................................................... 1 mm steel

Dimensions ....................................................................190.5 W x 191.7 D x 30 H mm

Weight ....................................................................................................................985 g

Digital Video Signal

Supported signals ........................................................................... DVI 1.0, HDMI 1.3

Signal standard ................. DVI and HDMI standard which supports embedded audio

Supported resolutions ............................ up to 1920x1200@60Hz, 1920x1080@60Hz

Deep color support (output) .....................................................converted to 8 bit / color

HDCP compliant ...................................................................................................... yes

EDID support .............................................. two built-in EDIDs (stereo / AC3 support)

Cable length (HDM input port) ...................................................................... max. 30 m

Video latency .............................................................2-3 frames (=33..50 ms @ 60Hz)

Power

Power supply ....................................................................... external power supply unit

Power adaptor .................. Input 100-240V AC 50-60 Hz, 1.5A, Output 24V DC, 2.7 A

Power consumption ............................................................................................... 12W

Power over TPS..........................................................................................................no

Connectors

Input ports .................................................................RJ45 (TPS interface), HDMI input

Ethernet ................................................................................................................. RJ45

Serial port ..................................................................................................D-Sub 9 male

Power ........................................................................................... locking DC connector

TPS port (HDBaseT

-compatible)

Ethernet pass-through ............................................................................................. yes

RS-232 pass-through ............................................................................................... yes

IR pass-through ................................................................................................................yes

Error Responses

When undened value is sent (e.g. S SOURCE 9) the response will be ERROR. Unknown

and insufcient commands are not processed, response is not sent.

The Handling of the Batteries

Use only standard batteries. Do not use new and used batteries together. This may cause a

battery to break or leak and may cause re, injury, or contamination (damage). When replacing

the batteries, insert them with right polarity. Otherwise, the battery may become damaged or it

may cause re, personal injury or damage due to leakage of the internal liquid. The batteries

(and rechargeable batteries) are not ordinary refuse and must be returned for recycling

purposes. The customer is responsible for returning the used or rechargeable batteries for

recycling. Be careful that children do not place the batteries in their mouths when removed

from the remote control. Place the battery in a location that children or infants cannot reach.

Correct Disposal of Batteries in this Product

This marking on the battery indicates that the batteries in this product should

not be disposed of with other household waste at the end of their working life.

Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery

contains mercury, cadmium or lead above the reference levels in EC Directive

2006/66. If batteries are not properly disposed of, these substances can

cause harm to human health or the environment. To protect natural resources and to promote

material reuse, please separate batteries from other types of waste and recycle them through

your local, free battery return system.

640x480 60/72/75p

800x600 56/60/72/75p

720x480 60p

720x480 60i

720x576 50p

720x576 50i

1024x768 60/70/75p

1280x720 50/60p

1280x800 60p

1280x1024 60/75p

1600x1200 60p

1680x1050 60 *p

1920x1080 50/60p

1920x1080 50/60i

1920x1200 60p

Querying the Status of the Current Settings

Format Example

Command

Response

R●STATUS<CR><LF>

ST<status_parameters>

→

←

r status

ST2x122000002xx

Response Parameter Description

2 [SOURCE] TPS input is selected

x reserved

12 [OUTPUT] output resolution is 1600x1200p60

2 [ASPECT] image aspect is ‘best t’

0 [AUDIO DELAY] no audio delay

0 [AUDIO MUTE] audio is unmuted

0 [KEY LOCK] front panel buttons are unlocked

0 [EDID TYPE] current EDID does not support audio

0 [HSYNC SHIFT] H sync shift is off

2 [INFO DISPLAY] input info is always displayed (OSD)

x reserved

Setting the Aspect Ratio of the Output Signal

ASPECT <set> 1 = stretch/full

2 = best t

3 = t width

4 = t height

5 = 14:9

6 = 1 to 1 and center

Maximum Extension Distances

Resolution Pixel

clock rate

Cable lengths (Auto / Long reach TPS mode)

CAT5e (AWG24) CAT7 (AWG26) CAT7 (AWG23)

1024x768@60Hz 65 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*

1280x720p@60Hz 73.8 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*

1920x1080p@60Hz (24bpp) 148.5 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m*

1920x1200@60Hz 152.9 MHz 100 m / NA 90 m / NA 120 m / NA

1600x1200@60Hz 162 MHz 100 m / NA 90 m / NA 120 m / NA

* Long reach TPS mode supports pixel clock frequencies up to 148.5 MHz.

To specify the accurate extension distances, please also check the documentation of the

connected HDBaseT-compatible device.



CAT7 SFTP AWG23 cable is always recommended.

Firmware Upgrade

To have the latest rmware running in your device, please do the followings:

1. Contact Lightware Support to get the latest rmware le.

2. Copy the rmware le to an USB ash drive. Make sure that the le system is FAT/FAT32

and the name of the rmware le is MSTFLASH_FILE_CH_521RX.bin.

3. Disconnect the power supply unit from the receiver.

4. Insert the pen drive into the USB service port of the receiver.

5. Press the Menu button and keep it pressed.

6. Connect the power supply to the receiver. The device is powered on, the upgrade is

started while the front panel lights in red; release the Input LED Menu button.

7. After cca. 30 seconds later the process is nished the front panel is blinking in Input LED

green/red and the Power LED also blinks.

8. Unplug the power supply remove the USB pen drive and reconnect the PSU again.

Software Control – Using Lightware Device Controller

The device can be controlled from a computer using the Lightware Device

Controller (LDC) software. The application is available at www.lightware.com

(Product Families / Software menu). Install the software it on a Windows PC

or a Mac OS X and connect to the device as follows.

Connecting via the RS-232 Port

1. Connect a computer to the RS-232 port of the receiver by a cross-link serial cable.

2. Launch the LDC software and select the tab.Serial Devices

3. Press the Query button of the given COM port, select the device and press the Connect

button.

Connecting via the TPS Line to an MX-FR Matrix Switcher (TPS Output Board)

1. Connect the receiver to an MX-FR matrix with TPS output port.

2. Connect the matrix to a LAN and connect a computer to the same LAN.

3. Start the LDC software and connect to the matrix listed at Ethernet Devices tab.

4. Open the Port properties panel of the given TPS output port and press the Open remote

device settings button at the bottom of the window.



The preferred resolution of the last attached sink will be the default when connected.

PIN : 2.1mm GPIO

RS-232

TX RX

AUD IO2 I N

DVI -I IN

IR IN IR OUT

LIVE

RS-232

SRVC

LINK

12V 1A DC

LAN

Internet

TPS connection

CATx up to 170 m

LAN

VGA

Laptop

Monitor

Blu-ray player

UMX-TPS-TX140

HDMI-TPS-RX120-HDSR

Access

Point Ethernet

switch

HDMI

12V DC

power adaptor

1400x1050@60Hz

1920x1080@50Hz

1360x768@60Hz

1600x1200@60Hz

24V DC

power adaptor

HDMI OUT HDMI IN

SERVICE MENU ENTER

Set to XGA

Set to 10 80p

Specyfikacje produktu

Marka:	Lightware
Kategoria:	przedłużacz AV
Model:	HDMI-TPS-RX120-HDSR
Kolor produktu:	Czarny
Wysokość produktu:	30 mm
Szerokość produktu:	160 mm
Głębokość produktu:	191.7 mm
Waga produktu:	800 g
Technologia łączności:	Przewodowa
Bluetooth:	Nie
Certyfikaty:	CE
Ilość portów USB:	1
Obsługiwany typ USB:	USB Typu-A
Gniazdko wyjścia DC:	Tak
Zasilacz sieciowy:	Tak
Napięcie pracy:	24 V
Wi-Fi:	Nie
Kanały wyjścia audio:	5.1 kan.
Przewodowa sieć LAN:	Tak
Pobór mocy:	17 W
Diody LED:	Tak
Model:	Amplituner
Prąd wejściowy:	0.6 A
Maks. rozdzielczość:	1920 x 1200 px
Wersja HDMI:	1.3
HDCP:	Tak
Szerokość pasma:	6.75 Gbit/s
Możliwości montowania w stelażu:	Tak
Materiały:	Metal
Wersja USB:	2.0
Złącze światłowodowe:	Toslink
Obsługiwane rozdzielczości grafiki:	1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA)
HDMI in:	1
Zdalne wejście IR:	1
Wejśćie 3,5 mm:	Tak
Ilość klatek:	3 fps
Zdanlne wyjścia IR:	1
Szeregowe porty komunikacyjne:	1
Interfejs SCSI:	RS-232
Obsługiwane typy kabli:	Cat5, Cat6, Cat7
Wejścia RJ-45:	1
Rozszerzone dane identyfikacyjne wyświetlacza (EDID):	Tak
Przejście HDCP:	Tak
Przejście RS-232:	Tak
Brak kompresji wideo:	Tak
Emulacja EDID (TX):	Tak