Instrukcja obsługi Lightware DVI-TP-RX100DL

Lightware przedłużacz AV DVI-TP-RX100DL

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lightware DVI-TP-RX100DL (1 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

Quick Start Guide

DVI-TP-RX100DL

DVI-TP-TX200DL

Further information

The document is valid with the following rmware version: 1.1.5 for RX and 1.3.1 for TX.

The User’s manual of this appliance is available at www.lightware.eu.

See the Downloads section on the website of the product.

sales@lightware.eu

+36 1 255 3800

support@lightware.eu

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 1.0

19200012

Important safety instructions

Please read and keep the information in the attached safety instructions supplied with the

product before start using the device.

Introduction

Lightware TP-DL series transceivers are Dual-Link DVI over Twisted pair extenders which

transmit Dual-Link DVI-D signals over two CATx cables. Accessible distances depend on the

used cable quality and signal resolution. The DVI-TP-TX200DL transmitter includes an EDID

Manager and built-in DVI distribution amplier for local monitor Output.

Only two CAT cables are needed for Dual-Link DVI signal transmission, there is no need for

third CAT cable to transmit EDID. If a lower resolution Single-Link signal is transmitted, only

one CAT cable is needed between the transmitter and the receiver.

TP-DL series transceivers support the highest resolutions up to 3840 x 2400 including all

HDTV resolutions: 720p, 1080p, 2K. DVI-TP-TX200DL stores and emulates 100 EDID, 50

of which are factory preset and 50 are user programmable.

Box contents

Extender unit 5V DC power adaptor

with interchangeable plugs

Safety and warranty info,

Quick Start Guide

Powering on

1. After the system is complete, rstly connect the output of the Power Adaptor to the

extenders then connect the adaptor to the socket.

2. At rst the extenders display the rmware version using the the upper two LEDs. The

following example shows this process for a rmware version of 1.3.1:

RED blinks once, short pause.

GREEN blinks three times, short pause.

GREEN blinks once.

3. The EDID INVALID LED on the transmitter lights up for 2-3 seconds, then the upper two

LEDs display the EDID status (if the selected EDID is valid or invalid).

4. The attached DVI source and monitor(s) can be powered on.



If none of the LEDs light up upon power-up, the unit is most likely damaged and further

use is not advised. Please contact support@lightware.eu.

Adjusting the input equalization

The amplitude of high frequency signals decreases after they pass through long distances

in copper cables. To counter-act this phenomenon, the receiver amplies the signal while

maximizing the amplitude at a certain level. The receiver offers two equalization modes:

automatic and manual. The mode can be toggled by pressing the EQ MODE SELECTION

button.



It is always advised to use the automatic mode and only adjust the equalization

manually if the auto mode does not give a good result.

Front and rear views - Transmitter

Front and rear views - Receiver



The extenders do not have networking capabilities. Do not connect a Local Area

Network device or a PC to the RJ45 sockets of the devices. Doing so may damage the

unit!

QEDID

rotary switches

The rotary switches select one of the EDID memory

addresses.

WLearn EDID

button

Stores the EDID of the display device attached to the

output in the selected memory address.

EStatus LEDs The LEDs give feedback about the state of the units and

the video signal.

RDVI input Connect one dual-link DVI-D or DVI-I cable (only digital

pins are connected internally) between the DVI source and

the transmitter.

TMonitor output Connect one dual link DVI-D or DVI-I cable (only digital

pins are connected internally) between the transmitter and

the local display device. The output connector is able to

supply 500 mA current on pin 14 to power ber optical DVI

extenders like DVI-OPT-TX100.

YCATx output(s) Connect two CATx cables between the transmitter and the

receiver.

UDC 5V input Connect the output of the supplied 5V DC power adaptor or

use Lightware’s rack mountable power supply.

Legend - Transmitter

QStatus LEDs The LEDs give feedback about the state of the units and

the video signal.

WEQ mode

selector button

Toggles between automatic and manual EQ mode. The EQ

mode status LEDs indicate which mode is currently active.

EEQ level adjust The 25-turn potentiometer can be used to precisely set

the right amount of equalization in manual EQ mode.

The potentiometer does not stop at the end positions,

but rotates indenitely. After reaching the end position, a

clicking sound can be heard at every full turn of the knob.

RCATx input Connect one CATx cable between the receiver and the

transmitter.

TDVI output Connect one dual link DVI-D or DVI-I cable (only digital

pins are connected internally) between the receiver and

the local display device. The output connector is able to

supply 500 mA current on pin 14 to power ber optical DVI

extenders like DVI-OPT-TX100.

YDC 5V input Connect the output of the supplied 5V DC power adaptor or

use Lightware’s rack mountable power supply.

Legend - Receiver

Typical application

Status LEDs - Transmitter

EDID INVALID

BLINKING: invalid EDID is read from the connected sink or EDID learning failed.

ON: invalid EDID is selected by the rotary switches.

EDID VALID

BLINKING: valid EDID is received from the connected sink or EDID learning is successful.

ON: valid EDID is selected and emulated by the rotary switches.

MONITOR

ON: a sink is connected to the Monitor output port and sends a valid Hot plug signal.

SRC +5V

ON: a DVI source is connected, powered on and sends the 5V signal.

Status LEDs - Receiver

MANUAL EQ

ON: Manual equalization mode is active.

AUTO EQ

ON: Auto equalization mode is active.

SIGNAL PRESENT

ON: a valid DVI clock signal is present on the CATx (video) input port.

MONITOR HOTPLUG

ON: a sink is connected to the DVI output port and sends a valid Hot plug signal.

Maximum twisted pair distances

Resolution Vfreq

(Hz)

Pixel clk

freq. (MHz)

Cat5e

UTP

Cat6

UTP

Cat6

FTP

Cat7

S/FTP

640x480 60 25.2 60 m 65 m 70 m 80 m

800x600 60 40.0 60 m 65 m 65 m 75 m

1024x768 60 65.0 55 m 60 m 60 m 75 m

1280x720p 60 74.2 55 m 60 m 60 m 70 m

1280x1024 60 108.0 50 m 55 m 60 m 65 m

1400x1050 60 121.8 45 m 45 m 55 m 60 m

1600x1200 60 162.0 30 m 35 m 45 m 50 m

1920x1080p 60 148.5 30 m 35 m 45 m 50 m

1920x1200p 60 153.0 30 m 35 m 45 m 50 m

2048x1536p 60 208.0 50 m 55 m 60 m 65 m

2560x1600p 60 268.0 30 m 35 m 45 m 50 m

3840x2400p 30 304.0 30 m 35 m 45 m 50 m



Category 7 cable is always recommended since they are screened and foiled by standard.

EDID selection

Use a at head screwdriver to change the address. The left switch

sets the tens value, the right switch gives the ones value of the EDID.



Avoid the use of keys, coins, knives and other sharp objects.

Locking DC plug

Twist 90°clockwise to lock.

DVI-TP-R X-100DL

DUAL LINK DVI

CAT-A CAT-B

HDM I-T P-TX200D L

Safety and

warranty

info

Quick

Start

Guide

1 2 3 4

65 7

1 2 3

4 5 6

Specyfikacje produktu

Marka:	Lightware
Kategoria:	przedłużacz AV
Model:	DVI-TP-RX100DL
Kolor produktu:	Czarny
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	100 - 240 V
Wysokość produktu:	26 mm
Szerokość produktu:	100.4 mm
Głębokość produktu:	67.6 mm
Waga produktu:	230 g
Technologia łączności:	Przewodowa
Bluetooth:	Nie
Gniazdko wyjścia DC:	Tak
Zasilacz sieciowy:	Tak
Napięcie pracy:	5 V
Wi-Fi:	Nie
Przewodowa sieć LAN:	Tak
Pobór mocy:	7 W
Diody LED:	Tak
Model:	Amplituner
Prąd wyjściowy:	2.5 A
Adapter zewnętrznego zasilania:	Tak
Prąd wejściowy:	1 A
Maks. rozdzielczość:	3840 x 2400 px
Szerokość pasma:	1.65 Gbit/s
Możliwości montowania w stelażu:	Tak
Materiały:	Metal
Maksymalny dystans transferu:	50 m
Obsługiwane rozdzielczości grafiki:	1920 x 1080 (HD 1080), 2560 x 1600 (WQXGA), 3840 x 2400
Obsługiwane tryby wideo:	1080p
Obsługiwane typy kabli:	Cat5, Cat6, Cat7
Porty wyjścia DVI:	1
Rozszerzone dane identyfikacyjne wyświetlacza (EDID):	Tak
Przejście HDCP:	Nie
Emulacja EDID (TX):	Tak
Pamięć EDID (TX):	Tak