Instrukcja obsługi Lightware DVI-HDCP-OPTM-TX90

Lightware przedłużacz AV DVI-HDCP-OPTM-TX90

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lightware DVI-HDCP-OPTM-TX90 (2 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Quick Start Guide

DVI-HDCP-OPTM-TX90

DVI-HDCP-OPTM-RX90

DVI-HDCP-OPTS-TX90

DVI-HDCP-OPTS-RX90

Further Information

The Product Brief of this appliance is available on www.lightware.com.

See the section on the dedicated product page.Downloads

sales@lightware.com

+36 1 255 3800

support@lightware.com

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 3.0

19200094

Important Safety Instructions

Please read the supplied safety instruction

document before using the product and

keep it available for future reference.



CAUTION - The use of controls or adjustments or any performance of procedures

other than those specied herein may result in hazardous radiation exposure.

Introduction

OPTM series

Lightware’s DVI-HDCP-OPTM-TX90 and DVI-HDCP-OPTM-RX90 pair is a DVI-D ber

transmitter and receiver set for up to 240 m (in case of OM2/OM3/OM4 cable) distance

transmission.

Using Single Fiber Technology the DVI-D signal with HDCP encryption is transmitted over

only one multimode 50/125 (or 62.5/125) ber core. Sources and display devices are

galvanically isolated against ground loops and hum effects, and no delay occurs in the signal,

the video image is transported without any frame latency.

OPTS series

The DVI-HDCP-OPTS-TX90 and DVI-HDCP-OPTS-RX90 pair is a DVI-D ber transmitter

and receiver set for up to 10 km (in case of OS2 cable) distance transmission.

Using Single Fiber Technology the DVI-D signal with HDCP encryption is transmitted over

only one single mode 9/125 ber core. Sources and display devices are galvanically isolated

against ground loops and hum effects, and no delay occurs in the signal, the video image is

transported without any frame latency.

Box Contents

Extender unit 5V DC power adaptor

with interchangeable plugs

USB cable with

micro USB plug

Safety and Warranty Info,

Quick Start Guide

DVI-D input plug

(transmitter)

DVI-D (single link) plug for receiving the DVI-D/HDMI input

signal from the source device.

Status LED Indicates the current status of the transmitted or received

optical signal.

FAST BLINKING The booting up procedure is in progress.

SLOW BLINKING No ber optical communication between TX and

RX devices.

ON The ber link is established successfully

between TX and RX.

Maximum Extension Distances

Singlemode (OPTS) Multimode (OPTM)

OS1 OS2 OM1 OM2 OM3 OM4

(62.5/125) (50/125) (50/125) (50/125)

For all resolution 5000 m 10000 m Not

supported 240 m

Top View - Transmitter (TX)

Top View - Receiver (RX)

USB micro-B

connector

USB micro-B connector is for the external powering of the

extender.

LC out connector

(transmitter)

LC ber optical connector for multimode ber output.

DVI-D output

plug (receiver)

DVI-D (single link) plug for transmitting the DVI-D/HDMI

output signal to the sink device.

LC in connector

(receiver)

LC ber optical connector for multimode ber input.

Rear View - Transmitter (TX) and Receiver (RX)

Fiber Optical Port

Connector type LC simplex receptacle ...........................................................................

Laser wavelengths (OPTM) 850, 1310, 1550 nm...........................................................

Laser wavelengths (OPTS) 1490, 1310, 1550 nm .........................................................

Optical loss budget (OPTM) 7 dB (worst case) ...............................................................

Optical loss budget (OPTS) 11 dB (worst case) ..............................................................

Laser class specication.....................................................................................Class 1

Compliance ........................................................................................ EN 60825-1:2008

Power

Power supply (TX) External power adaptor / USB / DVI-D .............................................

Power supply (RX) External power adaptor / USB ..........................................................

Power adaptor In 100-240 V AC 50/60 Hz, Out 5V DC, 1 A ...........................................

Power connector USB micro-B ........................................................................................

Enclosure

Material ............................................................................................... 1 mm solid metal

Enclosure dimensions in mm 40 W x 74 D x 15 H .........................................................

Enclosure dimensions in inch 1.5 W x 2.9 D x 0.6 H ......................................................

Weight .....................................................................................................80 g (0.17 lbs)

Specication

General

Compliance CE ...............................................................................................................

EMC Immunity IEC/EN 55035:2017 ..............................................................................

EMC Emission IEC/EN 55032:2015 ..............................................................................

Safety .......................................................................................................IEC/EN 60065

Warranty .............................................................................................................3 years

Cooling ............................................................................................................. Passive

Power consumption - TX 2.35 W ....................................................................................

Power consumption - RX 1.9 W ......................................................................................

Operating temperature ....................................................... 0 to +50˚C (+32 to +122˚F)

Storage temperature .........................................................-40 to +85˚C (-38 to +185˚F)

Operating humidity 10% to 90%, non-condensing .........................................................

Video delay 0 frame .........................................................................................................

HDCP pass-through .................................................................................................Yes

EDID emulation Transparent EDID..................................................................................

DVI-D Plug

Connector type 24-pole DVI-D ........................................................................................

Resolution ..........................................1920x1200 or 2048x1080 maximum resolutions

Connecting Steps

Follow the installation steps to connect the extenders between the source and sink devices:

OPTM

OPTS

Connect the or themultimode (in the case of OPTM) singlemode (in the

case of OPTS) fiber optical cable to the LC IN connector of the receiver.

DVI-D

Connect the to the input port of the sink device DVI-D plug of the receiver

(e.g. Projector). The extender reads the EDID from the display (projector,

monitor, etc), and outputs the video signal according to the set resolution.

Fasten the extender with the mounting screws.

Power

Power on the by choosing one of the powering options below:receiver

Connect the to the micro USB USB plug of the power adaptor

connector of the receiver.

Connect the provided between the USB-A - USB micro-B cable

extender and the sink device.

OPTM

OPTS

Connect the or themultimode (in the case of OPTM) singlemode (in the

case of OPTS) fiber optical cable to the LC OUT connector of the transmitter.

DVI-D

Connect the to the output port of the source DVI-D plug of the transmitter

device (e.g. PC). Fasten the extender with the mounting screws.

Power

Finally power on the by choosing one of the powering options below:transmitter

Connect the to the micro USB USB plug of the power adaptor

connector of the transmitter.

Connect the provided cable between the USB-A - USB micro-B

extender and the source device.

If the DVI source device is able to provide enough 5V DC current

(500mA), there is no need for external 5V DC power. The extender is

powered immediately when the source device is switched on.

Check the Status LED. When the connection has been made successful, the

blue LEDs on the transmitter and receiver will appear solid (not blinking).



It is not recommended to power on the devices before the nal step.

DVI-HDCP-OPT-90 series

transmitter

DVI-HDCP-OPT-90 series

receiver

PC Projector

Power adaptor

OPTM

OPTS

Power

DVI-D

DVI-HDCP-OPTS-RX90

S/N: 7A000942

DVI-HDCP-OPTS-TX90

S/N: 7A000941

364

Safety and

Warranty

Info

Quick

Start

Guide

CLASS 1 LASER PRODUCT

Important Safety Instructions

Please read and keep the information in the attached safety instructions supplied with the

product before starting using the device.

Safety Symbols Legend

Symbol Description

Caution

Laser radiation

WARNING

To prevent injury, the apparatus is recommended to securely attach to the oor/wall or

mount in accordance with the installation instructions. The apparatus shall not be exposed

to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed

on the apparatus. No naked ame sources, such as lighted candles, should be placed on the

apparatus.

WEEE ( Waste Electrical & Electronic Equipment )

Correct Disposal of This Product

This marking shown on the product or its literature, indicates that it

should not be disposed with other household wastes at the end of its

working life. To prevent possible harm to the environment or human

health from, uncontrolled waste disposal, please separate this from

other types of wastes and recycle it responsibly to promote the

sustainable reuse of material resources.

Household users should contact either the retailer where they purchased, this product,

or their local government ofce, for details of where and how they can take this item for

environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the

purchase contract. This product should not be mixed with other commercial wastes for

disposal.

Specyfikacje produktu

Marka:	Lightware
Kategoria:	przedłużacz AV
Model:	DVI-HDCP-OPTM-TX90
Kolor produktu:	Czarny
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	100 - 240 V
Technologia łączności:	Przewodowa
Certyfikaty:	CE, IEC/EN 55035:2017, IEC/EN 55032:2015, IEC/EN 60065
Ilość portów USB:	1
Obsługiwany typ USB:	Micro-USB B
Zasilacz sieciowy:	Tak
Zakres temperatur (eksploatacja):	0 - 50 °C
Zakres wilgotności względnej:	10 - 90 %
Wi-Fi:	Nie
Przewody:	Micro-USB
Kompatybilność 3D:	Tak
Diody LED:	Link
Zakres temperatur (przechowywanie):	-40 - 85 °C
Model:	Nadajnik AV
Prąd wejściowy:	1 A
Maks. rozdzielczość:	2048 x 1080 px
HDCP:	Tak
Szerokość pasma:	6.75 Gbit/s
Materiały:	Aluminium
Wersja USB:	2.0
Złącze światłowodowe:	LC
Maksymalny dystans transferu:	300 m
Obsługiwane rozdzielczości grafiki:	1920 x 1200 (WUXGA), 2048 x 1080
Obsługa funkcji Plug & Play:	Tak
Ilość klatek:	0 fps
Wymiary transmitera (SxGxW):	40 x 74 x 15 mm
Waga transmitera:	80 g
Porty wejścia DVI:	1
Struktura światłowódu jednomodowego:	Multifunkcyjny
Rozszerzone dane identyfikacyjne wyświetlacza (EDID):	Tak
Zabezpieczenie przed wyładowaniami elektrostatycznymi (ESD):	Tak
Zużycie prądu (nadajnik) (max):	2.35 W
Zużycie prądu (odbiornik) (max):	1.9 W
Klasa:	1M
Obsługiwane długości fal światłowodu:	1550,850,1310 nm
Przejście HDCP:	Tak
Budżet strat optycznych:	7 dB
Czułość odbiornika OMA:	16 dBm
Wyjście nadajnika OMA:	9 dBm
Emulacja EDID (TX):	Tak