Instrukcja obsługi Lectrosonics DCHT

Lectrosonics Niesklasyfikowane DCHT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lectrosonics DCHT (24 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/24
DCHT
Digital Transmitter
DCHT, DCHT/E01
INSTRUCTION MANUAL
Rio Rancho, NM, USA
www.lectrosonics.com
Fill in for your records:
Serial Number:
Purchase Date:
Quick Start Steps
1) Install good batteries and turn power on (see pages
5 and 7).
2) Set compatibility mode to match the receiver (see
page 11).
3) Connect signal source, select input type and adjust
input gain for optimum modulation level (see page
10).
4) Set or sync frequency to match receiver (see page
11, 12). Also see receiver manual for scanning pro-
cedure.
5) Set encryption key type and sync with receiver (see
page 13).
6) Set programmable switch to desired function (see
page 13).
7) Verify RF and audio signals are present at the
receiver (see receiver manual).
DCHT, DCHT/E01
LECTROSONICS, INC.
2
Table of Contents
Quick Start Steps 1 ................................................................
Introduction 3 ...........................................................................
General Technical Description ........................................... 3
DSP-controlled Input Limiter 3 ...............................................
Encryption 3 ...........................................................................
Features and Functions 4 .......................................................
Optional Battery Eliminator 4 .................................................
Whip Antennas 4 ....................................................................
Battery Status LED Indicator 5 ..............................................
Belt Clips 5 .............................................................................
IR (infrared) Port 5 .................................................................
Status LED 5 ..........................................................................
Connecting the Signal Source 5 ............................................
Battery Installation 5 ...............................................................
DCHT, DCHT/E01 Block Diagram 6 .......................................
Powering On and Off 7 ............................................................
Powering On in Operating Mode 7 .........................................
Powering On in Standby Mode 7 ...........................................
Powering Off 7 .......................................................................
Main Menu and Setup Screen Details 7 .................................
Entering the Main Menu 7 ......................................................
Main Window Indicators 7 .....................................................
LCDMenu Map 8 .......................................................................
Input Menu 10 ..........................................................................
Adjusting the Input Gain for Analog Inputs 10 .........................
Selecting the Low Frequency Roll-off 10 .................................
Selecting StMode (stereo mode) 10 ........................................
Selecting Input Type ............................................................ 10
Selecting Input Configuration 10 ..............................................
Xmit Menu 11 .............................................................................
Selecting Frequency 11 ...........................................................
Selecting Transmitter Output Power 11 ....................................
Selecting Receiver Compatibility Mode 11 ..............................
Turning Rf On/Off 11 ................................................................
Selecting M2R Receiver Functions 12 .....................................
GetFrq 12 .................................................................................
SendFrq 12 ..............................................................................
GetAll 12 ..................................................................................
SendAll 12 ................................................................................
Name... ................................................................................ 12
Flex 12 .....................................................................................
Key Menu 13 ...............................................................................
Encryption Key Management 13 ..............................................
KeyType 13 ..............................................................................
MakeKey 13 .............................................................................
WipeKey 13 ..............................................................................
SendKey 13 ..............................................................................
Setup Menu 13 ...........................................................................
Selecting AutoOn Feature 13 ...................................................
Selecting Programmable Switch Functions......................... 13
Enable/Disable Remote Control Function 14 ...........................
Selecting Battery Type ........................................................ 14
Locking/Unlocking Changes to Settings.............................. 14
Selecting Backlit Time ......................................................... 14
Turning LEDs Off/On 14 ...........................................................
Restoring Default Settings 14 ..................................................
About 14 .....................................................................................
Wireless Designer Software 15 ...............................................
Firmware Update Instructions 15 .............................................
Specifications 15 .......................................................................
Input Connections 16 ...............................................................
Microphone Cable Termination
for Non-Lectrosonics Microphones 17 .............................
LectroRM 18 ...............................................................................
Accessories 20 ..........................................................................
Troubleshooting 21 ....................................................................
Service and Repair 22 ...............................................................
Returning Units for Repair 22 ..................................................
Digital Transmitter
Rio Rancho, NM 3
Introduction
The DCHT, DCHT/E01 transmitter is designed to work
with a companion receiver (such as the Lectrosonics
M2R, part of the Duet IEM system) as an audio relay
between an audio production bag or cart and a camera
or other audio device. The 6-pin input jack accepts two
mic or line level analog signals or AES digital signals
from external sources with a variety of adapter cables.
Analog inputs can be linked for the same gain when
used with a stereo source, or operate independently
with individual settings.
This third generation digital design features specially
developed, high efficiency digital circuitry for extended
operating time on two AA batteries. The transmitter can
tune in coarse or fine steps across the UHF television
band from 470.100 to 607.950 MHz (E01 frequency
range is 470.100 to 614.375 MHz), with a selectable
output power of 10, 25 or 50 mW.
Studio quality audio performance is assured by high
quality components in the preamp, wide range input
gain adjustment and DSP-controlled limiting. and
settings are included for any lavaliere microphone,
dynamic microphones and line level inputs. Input gain
is adjustable over a 51 dB range in 1 dB steps to allow
a precise match to the input signal level, to maximize
dynamic range and signal to noise ratio.
A separate switch is provided on the top panel that can
be configured as mute, power or bypass.
The housing is constructed of solid machined aluminum
for lasting ruggedness. The exterior is finished with an
ultra hard, dark electroless nickel finish called ebENi.
Firmware updates are made through a side panel micro
USB port.
Canada ISED Notice
This device operates on a no-protection, no-interference basis. Should the user seek to obtain
protection from other radio services operating in the same TV bands, a radio licence is required.
For further details, consult Innovation, Science and Economic Development Canada’s document
Client Procedures Circular CPC-2-1-28, Voluntary Licensing of Licence-Exempt_Low-Power
Radio Apparatus in the TV bands.
General Technical
Description
DSP-controlled Input Limiter
The transmitter employs a DSP-controlled analog audio
limiter prior to the analog-to-digital converter. The limiter
has a range greater than 30 dB for excellent overload
protection. A dual release envelope makes the limiter
acoustically transparent while maintaining low distor-
tion. It can be thought of as two limiters in series, con-
nected as a fast attack and release limiter followed by
a slow attack and release limiter. The limiter recovers
quickly from brief transients, so that its action is hidden
from the listener, but recovers slowly from sustained
high levels to keep audio distortion low and preserve
short term dynamic changes in the audio level.
Encryption
When transmitting audio, there are situations where pri-
vacy is essential, such as during professional sporting
events, in court rooms or private meetings. For instanc-
es where your audio transmission needs to be kept
secure, without sacrificing audio quality, Lectrosonics
implements AES256 encryption in our digital wireless
microphone systems. High entropy encryption keys are
first created by the DCHT Transmitter. The key is then
synced with an encryption-capable digital receiver, via
the IR port. The audio will be encrypted and can only
be decoded if both DCHT and receiver have the match-
ing encryption key. If you are trying to transmit an audio
signal and keys do not match, all that will be heard is
silence.

Specyfikacje produktu

Marka: Lectrosonics
Kategoria: Niesklasyfikowane
Model: DCHT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Lectrosonics DCHT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Lectrosonics

Lectrosonics

Lectrosonics DBu-LEMO Instrukcja

29 Września 2024
Lectrosonics

Lectrosonics RATPAC Instrukcja

29 Września 2024
Lectrosonics

Lectrosonics DCHT Instrukcja

29 Września 2024
Lectrosonics

Lectrosonics RPS4 Instrukcja

29 Września 2024
Lectrosonics

Lectrosonics DHu Instrukcja

29 Września 2024
Lectrosonics

Lectrosonics MCAES3 Instrukcja

29 Września 2024
Lectrosonics

Lectrosonics ZS-LMB Instrukcja

29 Września 2024
Lectrosonics

Lectrosonics UMC16B-A1B1 Instrukcja

28 Września 2024
Lectrosonics

Lectrosonics WM Instrukcja

28 Września 2024
Lectrosonics

Lectrosonics ZS-LRLT Instrukcja

28 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024